1999 MITSUBISHI LANCER EVOLUTION VI lamp

CHASSIS ELECTRICAL – Front Fog Lamp54-39
FRONT FOG LAMP
SERVICE SPECIFICATIONS
ItemsStandard value
Headlamp aiming [Paren-
thesized are allowableVertical direction2° (349 mm) below horizontal line (H)
t
beam axis deviations 10 m
ahead of headlamp.]Horizontal direction3° (524 mm) leftward from vertical line (V)
ON-VEHICLE SERVICE
HEADLAMP AIMING
Bring the vehicle in the following conditions before aiming
the headlamp.

Check the tires for inflation pressure. Pump them up if
necessary to the labeled pressure level.

Set the vehicle unladen on a level floor.

Place one person (approximately 55 kg) on the driver’s
seat.

Maintain an engine speed of 2,000 r/min to keep the
battery in the charged condition.
1. Position the tester so that its converging lens faces the
fog lamp center to center at a distance of 10 m.
NOTE
Measure the center of the fog lamp as shown.
A: 572.5 mm (from the center of the vehicle body)
B: 360 mm
2. Remove the fog lamp bezel, and using the aiming
adjustment screw, aim the fog lamp to the standard value.
NOTE
The horizontal direction is non-adjustable. If the beam
axis deviation exceeds the standard value, check the
fog lamp to determine if it is installed out of position and
correct if necessary.
Face to face 10 m apart from
each other
AAB
Adjusting screw

CHASSIS ELECTRICAL – Front Fog Lamp54-40
Standard values:
Vertical direction2° (349 mm) below horizontal line
(H)
Horizontal direction3° (524 mm) leftward from
vertical line (V)
Caution:
(1) Perform aiming adjustments, one light at a time,
with the other headlamp disconnected so as not
to be lit unless circumstances compel otherwise.
When reconnecting the headlamps, be careful not
to upset their aim. Do not leave the headlamps
on for any longer than 3 minutes if their outer
lenses are covered with a surface covering
impervious to light.
(2) Do not mask the outer lenses by taping or in any
other way.
(3) Aiming adjustment must be completed with the
aiming adjustment screws turned in the tightening
direction.
FOG LAMP BULB REPLACEMENT
1. Remove the fog lamp.
2. Remove the cover.
3. Unhook the spring which secures the bulb and then
replace the bulb.
Caution
(1) Do not touch the surface of the bulb with hands
or dirty gloves. If the surface does become dirty,
clean it with alcohol or thinner, and let it dry
thoroughly before installing.
(2) To prevent the clouding of lens and ingress of
water into the lamp unit, install the socket cover
correctly.
Lamp center
Vertical
direction
High
intensity
zone
center
(optical
axis)High intensity zone
Horizontal directionV
H
Cover

CHASSIS ELECTRICAL – Front Fog Lamp
ILL
ILL
54-41
FOG LAMP
REMOVAL AND INSTALLATION
31
4 2
1. Front fog lamp switchFog lamp removal steps
2. Front bumper
3. Fog lamp bezel
4. Fog lamp assembly
INSPECTION
FOG LAMP SWITCH CONTINUITY CHECK
Switch positionTerminal No.p
1234–56
OFF
ON

CHASSIS ELECTRICAL – Rear Combination Lamp54-42
REAR COMBINATION LAMP
TROUBLESHOOTING
For the troubleshooting of the lighting monitor warning buzzer, refer to P.54-33.
REAR COMBINATION LAMP
REMOVAL AND INSTALLATION
Caution: SRS
Before removal of air bag module and clock spring, refer to GROUP 52B – SRS Service Precautions and Air Bag
Module and Clock Spring.
2
1
3
1. Column switchRear combination lamp removal
steps
2. Rear end trim
3. Rear combination lamp
INSPECTION
LIGHTING SWITCH CONTINUITY CHECK
Switch positionTerminal No.
Connector BConnector A
5671
LIGHTING
SWITCH
OFF
SWITCHTAIL
HEAD
Connector A Connector B

CHASSIS ELECTRICAL – Side Turn-signal Lamp54-43
SIDE TURN-SIGNAL LAMP
SPECIAL TOOL
ToolNumberNameUse
MB990784Ornament removerRemoval of side turn-signal lamp
SIDE TURN-SIGNAL LAMP
REMOVAL
INSTALLATION
Fit the hook side rearward.
Fender panelMB990784
LockMB990784
Lock
Fender
panel
Hook

CHASSIS ELECTRICAL – Hazard Warning Lamp Switch, Clock
ILL
ILL
54-44
HAZARD WARNING LAMP SWITCH, CLOCK
SPECIAL TOOL
ToolNumberNameUse
MB990784Ornament removerAir conditioner panel removal
HAZARD WARNING LAMP SWITCH
REMOVAL AND INSTALLATION
2
1 3
4
Hazard warning lamp switch
removal steps
1. Air conditioner panel
2. Switch holder
3. Hazard warning lamp switchClock removal steps
1. Air conditioner panel
4. Clock
INSPECTION
HAZARD WARNING LAMP SWITCH CONTINUITY
CHECK
Switch
iti
Terminal No.
position1245679–10
OFF
ON

– Heater Control Assembly and A/C Switch HEATER AND MANUAL
AIR CONDITIONER55-15
HEATER CONTROL ASSEMBLY AND A/C SWITCH
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Instrument Lower Panel and Heater Control Panel
Removal and Installation

Floor Console Assembly Removal and Installation

Foot Duct Removal and Installation
(Refer to P.55-31.)
3 4
1
2 5
Removal steps
AA1. Heater control assembly
2. Rear window defogger switch
3. A/C switch
4. Knob
5. Blower switch
REMOVAL SERVICE POINT
AHEATER CONTROL ASSEMBLY REMOVAL
1. Remove the heater control assembly mounting screws.
2. Bend the clamp and the bosses (2 each side), which
are inserted into the centre reinforcement.
3. Remove the heater control assembly.
Clamp
Boss
Boss

– Heater Control Assembly and A/C Switch HEATER AND MANUAL
AIR CONDITIONER55-16
INSTALLATION SERVICE POINT
AHEATER CONTROL ASSEMBLY INSTALLATION
1. Cut off the bosses and clamp shown before installing
a new heater control assembly.
2. Install the heater control assembly mounting screws.
3. Follow the steps below to install the air outlet changeover
damper lever cable.
(1) Set the air outlet changeover link of the heater unit
to the DEF position.
(2) Set the air outlet changeover control knob on the
heater control assembly to the DEF position.
(3) After inserting the inner cable into the link, pull the
outer cable to the heater control assembly side and
then fasten the outer cable to the clip of the heater
unit.
(4) After installation, operate the heater control knob to
check if the mode changeover can be accomplished
smoothly.
4. Follow the steps below to install the air mix damper lever
cable.
(1) Set the air mix damper link on the heater unit to
the MAX HOT position.
(2) Set the air mix damper knob of the heater control
assembly to the MAX HOT position.
(3) After inserting the inner cable into the link, pull the
outer cable to the heater control assembly side and
then fasten the outer cable to the clip of the heater
unit.
(4) After installation, operate the heater control knob to
check if the air mix damper can be actuated smoothly.
Clamp
Boss
Boss
DEF
position
MAX HOT position