1999 LEXUS SC300 light

INTERIOR EQUIPMENT
742. Bring the hand held garage door opener within about 25
mm (1 in.) of the button being programmed and push the
button on the hand held garage door opener. The signal from
the hand held garage door opener is sent to the vehicle's
opener.
3. When the frequency and code is registered, the indicator
light flashes rapidly. At this point, you can release both
buttons.
4. To program the remaining buttons, repeat steps º1º
through º3º.
If you want to replace an existing program with a new
program, select the button you want to program. Follow the
procedure from step 1.
If the transmitter has a ºrolling code featureº, it is
necessary to program the in±garage receiver after
programming
HomeLink
.
1. Locate the ºtrainingº or ºlearningº button on the
in±garage receiver and push and release this button.
Location of the button may vary by the garage door
opener manufacturer.
2. Firmly push and release the trained HomeLink
 button
2 times (some garage door manufacturer may r equire you
to push the HomeLink
 button up to 3 times) to complete
the process.
The garage door should now operate when the
HomeLink
 button is pushed. Do not use the HomeLink
 universal transmitter with any
garage door opener that lacks the safety stop and reverse
feature as required by Federal Safety Standards. This
includes any garage door opener model manufactured before
April 1, 1982.

INTERIOR EQUIPMENT
75
CAUTION
When programming or operating the garage door opener,
make sure there is no one around the moving door. It is
dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds as
long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized data
will be erased.FCC ID: CB2V94800
This device complies with FCC Rules part 15.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference that
may be received, including interference that may
cause undesired operation. WARNING: This
transmitter has been tested and complies with
FCC and DOC/MDC rules. Changes or
modifications not expressly approved by the
partly responsible for compliance could void the
user's authority to operate the device.

SECTION 1 ± 5
81
INSTRUMENTS AND CONTROLS
Exterior equipment
Hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . .
81
Trunk lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . .
83
Fuel tank cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. .
85
Moon roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
88
HOOD
To open the hood, pull the hood lock release lever under
the instrument panel. The hood will spring up slightly.

EXTERIOR EQUIPMENT
87
CAUTION

Do not smoke, cause sparks or allow open flames when
refuelling. The fumes are flammable.

When opening the cap, do not remove the cap quickly. In
hot weather, fuel under pressure could cause injury by
spraying out of the filler neck if the cap is suddenly
removed.
2. To remove the fuel tank cap, turn the cap slowly
counterclockwise, then pause slightly before removing it.
The removed cap can be stored on the back side of the fuel
filler door.
It is not unusual to hear a slight swoosh when the cap is
opened. When installing the cap, turn the cap clockwise until
you hear a click.
If the cap is not tightened securely, the malfunction indicator
lamp comes on. Make sure the cap is tightened securely.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible.

COMFORT ADJUSTMENT
109
OUTSIDE REAR VIEWMIRRORS
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object
seen in the outside rear view mirror on the passenger's side.
It is a convex mirror with a curved surface. Any object seen
in a convex mirror will look smaller and farther away than if
seen in a normal flat mirror.
When the inside rear view mirror darkens in ºAUTOº mode,
the outside rear view mirrors also darken to reduce the
reflection of the headlights of the following vehicle. For
details, see ºInside rear view mirrorº on page 113.
When you push the rear window defogger switch, the heater
panels in the outside rear view mirrors will quickly clear the
mirror surface.

COMFORT ADJUSTMENT
113
INSIDE REAR VIEW MIRROR
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between ºAUTOº
and ºDAYº.
The indicator comes on when the ºAUTOº mode is selected.
ºDAYº mode: The mirror surface is normal.
ºAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the ºAUTOº mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.

COMFORT ADJUSTMENT
118
Adjust the seat as needed and sit up straight and well back
in the seat. To fasten your belt, pull it out of the r etractor
and insert the tab into the buckle.
You will hear a click when the tab locks into the buckle.
The seat belt length automatically adjusts to your size and the
seat position.
The retractor will lock the belt during a sudden stop or on
impact. It also may lock if you lean forward too quickly. A
slow, easy motion will allow the belt to extend, and you can
move around freely. When a passenger's shoulder
belt is completely extended and
is then retracted even slightly, the belt is locked in that
position and cannot be extended. This feature is used to hold
the child restraint system securely. (For details, see ºChild
restraintº on page 143.) To free the belt again, fully retract the
belt and then pull the belt out once more.
If the seat belt cannot be pulled out of the retractor, firmly pull
the belt and release it. You will then be able to smoothly pull
the belt out of the retractor.

COMFORT ADJUSTMENT
121
Rear seat belts
Sit up straight and well back in the seat. To fasten your
belt, pull it out of the retractor and insert the tab into the
buckle.
You will hear a click when the tab locks into the buckle.
The seat belt length automatically adjusts to your size.
The retractor will lock the belt during a sudden stop or on
impact. It also may lock if you lean forward too quickly. A
slow, easy motion will allow the belt to extend, and you can
move around freely. When a shoulder belt is completely
extended and is then retracted even slightly, the belt is locked
in that position and cannot be extended. This feature is used
to hold the child restraint system securely. (For details, see
ºChild restraintº on page 143.)
To free the belt again, fully retract the belt and then pull the
belt out once more.If the seat belt cannot be pulled out of the retractor, firmly pull
the belt and release it. You will then be able to smoothly pull
the belt out of the retractor.