1999 LEXUS SC300 light

COMFORT ADJUSTMENT
129
CAUTION
The driver or front passenger too close to the steering wheel
or dashboard during airbag deployment can be killed or
seriously injured. Lexus strongly recommends that:

The driver sit as far back as possible from the steering
wheel while still maintaining control of the vehicle.

The front passenger sit as far back as possible from the
dashboard.

All vehicle occupants be properly restrained using the
available seat belts.
This indicator comes on when the ignition key is turned to
the ºACCº or ºONº position. It goes off after about 6
seconds. This means the SRS airbags are operating
properly.
The SRS airbag warning light system monitors the airbag
sensor assembly, inflators, warning light, interconnecting
wiring and power sources. (For details, see ºService
reminder indicators and warning buzzersº on page 53 for
instructions.)

COMFORT ADJUSTMENT
141
This SRS airbag system has a service reminder indicator to
inform the driver of operating problems. If either of the
following conditions occurs, this indicates a malfunction of
the airbags. Contact your Lexus dealer as soon as possible to
service the vehicle.

The light does not come on when the ignition key is turned
to the ºACCº or ºONº position, or remains on.

The light comes on while driving.

COMFORT ADJUSTMENT
153
CAUTION

After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.

Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.

If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retracted even slightly, it cannot be
extended.
To hold the infant seat securely, make sure the belt is in the
lock mode before letting the belt retract.

COMFORT ADJUSTMENT
161
CAUTION

After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.

Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.

If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retracted slightly, it cannot be extended.
To hold the convertible seat securely, make sure the belt is in
the lock mode before letting the belt retract.

COMFORT ADJUSTMENT
169
1. Adjust the driver's seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º or
º2º until the signal beeps.
The beep sound means that the positions are recorded in the
computer 's memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be
recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the memorized
position, then make the desired changes and perform step 2
above.Activating a memorized position

SECTION 1 ± 7
172
INSTRUMENTS AND CONTROLS
Theft deterrent
Theft deterrent system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
172
Theft prevention labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
175
THEFT DETERRENT SYSTEM
To deter theft of the vehicle, this system is designed to give
an alarm if any of the doors, trunk or hood is forcibly
unlocked or the battery terminal is disconnected and then
reconnected while the vehicle is locked.
The alarm blows the horn intermittently and flashes the
headlights, tail lights and other exterior lights.

THEFT DETERRENT
173
Setting the system
1. Turn the ignition key to the ºLOCKº position and
remove it.
The indicator light flashes by means of the engine
immobiliser system.
2. Close and lock all the doors, trunk and hood using an
ignition key or wireless remote control.If you lock them with wireless remote control, the turn signals
flash once.
The flashing indicator light changes to stay on when all the
doors, trunk and hood are closed and locked.
3. After 30 seconds, the indicator starts flashing and the
system is set.
Cancelling the system
When you unlock any door or trunk using an ignition key
or wireless remote control, the system is cancelled.
If you unlock any door or trunk with wireless remote control,
the turn signals flash twice.
Activating the system
The alarm sounds for 60 seconds if any of the following are
operated:


Unlocking any door or trunk without using an ignition key
or wireless remote control.

Opening the hood forcibly.

Reconnecting the battery.
If any door is unlocked and the ignition key is not in the
ignition switch during the alarm sounding, its door is
automatically locked.

THEFT DETERRENT
174To stop the alarm: Use either of the following methods.


Unlock the door or trunk using an ignition key or wireless
remote control.

Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The front doors should be locked with the ignition key or
wireless remote control. Be sure to wait until the indicator
light starts flashing.
3. Unlock one of the doors from the inside.
The system should activate the alarm.
4. Unlock any of the doors with a key or the wireless
remote control to cancel the system.
5. Repeat this operation for the other doors and hood.
When testing the hood, also check that the system is activated
when the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it checked by your
Lexus dealer.
NOTICE
Disconnecting the battery may result in the erasure of
information you have set in the computer memory. After
reconnecting the battery, check that the memorized data
has been retained. If it has been erased, input it into the
computer once more.