Page 81 of 432

GAUGES, METERS AND SERVICE REMINDER INDICATORS
63
º± ±º, take your vehicle to your Lexus dealer.
(2) Driving time
(Figures with ºE/Tº)
The total time during the engine running is displayed.
When the engine is started again after the ignition is off, the
driving time is added to the previous value. Up to 99 hours
59 minutes can be displayed. When the driving time exceeds
99 hours 59 minutes, the display returns to 0 and recounting
starts.
To count from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(3) Average vehicle speed(Figures with ºAVG MPHº)
The average vehicle speed is calculated and displayed
based on the total driving distance and the total driving
time with the engine running.
The displayed value is updated every 10 seconds.
To calculate from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(4) Average fuel consumption(Figures with ºAVG MPGº)
The average fuel consumption is calculated and displayed
based on the total driving distance and the total fuel
consumption with the engine running.
The value is updated every 10 seconds.
To calculate from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(5) Momentary fuel consumption(Figures with ºMPGº)
The momentary fuel consumption is calculated and
displayed based on the driving distance and the fuel
consumption for 3 seconds with the engine running.
The value is updated every 3 seconds.
If you are driving at low speeds just before stopping, the
accurate figure may not be shown.
For the display (1), (3), (4) or (5), º± ±º will appear\
in case
the data for calculation is not appropriate.
Page 82 of 432
GAUGES, METERS AND SERVICE REMINDER INDICATORS
64
INSTRUMENT PANEL LIGHTCONTROL
To adjust the brightness of the instrument panel lights,
turn the knob.
When the headlight switch is in the first or second click stop,
you can also adjust the brightness of the displays on the audio
and air conditioning systems using this knob.
Page 87 of 432
INTERIOR EQUIPMENT
69
CLOCK
The digital clock indicates the time with the ignition key
at the ºONº position. To reset the hour, press the ºHº
button. To reset the minutes, press the ºMº button. To
adjust the time to the nearest hour, press the º:00º button.
For example, if the º:00º button is pressed when the time is
between 9:30 ± 9:59 or between 10:01 ± 10:29, the time will
change to 10:00.
With the tail lights on, the background brightness of the time
indication will be reduced.
If the electrical power source has been disconnected from the
clock, the time display will automatically be set to 1:00 (one
o'clock).CIGARETTE LIGHTER AND ASHTRAY
Front cigarette lighter and ashtray
Page 198 of 432
AIR CONDITIONING AND AUDIO
180The automatic air conditioning automatically maintains the
set temperature.
This air conditioning features automatic fan speed and air
flow
control which automatically selects the most suitable fan
speed and air flow to control the temperature. The ignition
key must be in the ºONº position.
You may use manual control to override the automatic
settings.
You can adjust the brightness of the display. See ºInstrument
panel light controlº on page 64 for details.
Page 199 of 432

AIR CONDITIONING AND AUDIO
181
(a) Climate control
SETTING OPERATION ± automatic control
1. Push the ºAUTOº knob.
Air flow quantity, switching of the diffusers, on±off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are
automatically adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the button depressed is set. Other conditions continue to be
adjusted automatically. 2. Turn the ºTEMPº knob until the desired temperature
is displayed.
The ºTEMPº knob is used to set the desired passenger
compartment temperature. The temperature of air delivered
to the passenger compartment will be controlled
automatically according to the setting. The figures on the
panel indicate degrees Fahrenheit.
SETTING OPERATION ± manual control
If manual air flow selection is desired ±
The outlets from which air is delivered can be selected
manually by pushing either side of the air flow control
(MODE) button. The mode appears on the display.
The function of each mode is as follows:
PANEL mode ± Directs air flow at face level.
BI±LEVEL mode ± Directs air flow at face level and
at floor level for both front and rear. Except in ventilation, the
air to the floor is slightly warmer than air to the face.
FLOOR mode ± Directs air flow mostly at floor level
for both front and rear.
FLOOR/WINDSHIELD mode ± Directs air flow to
the windshield and front side windows as well as floor level
for both front and rear.
FRONT WINDSHIELD mode ± Directs air flow
mostly to the windshield and front side windows.
When this mode is selected while operating in automatic
mode, the air conditioning is set to operate and the OUTSIDE
Page 200 of 432

AIR CONDITIONING AND AUDIO
182AIR mode is set.
If you push the ºFRONT WINDSHIELDº button once again
while in the FRONT WINDSHIELD mode, the mode then
returns to the last mode used.
CAUTION
Do not use the FRONT WINDSHIELD mode during cooled
air operation in extremely humid weather. The difference
between the temperature of the outside air and that of the
windshield could cause the outer surface of the windshield to
fog up blocking your vision.
If quick heating or cooling is desired ±
Obtain maximum power by turning the ºTEMPº knob fully.
At this time, ºMAX. HOTº or ºMAX. COLDº will appear on
the display.
If manual fan speed control is desired ±
The fan speed can be set to your desired speed by pushing
either
side of the fan speed control
(FAN) button. The
higher the fan speed is, the more air is delivered. Pushing in
the
(OFF) button turns off the fan.
To remove exterior windshield frost, use the high speed
setting. Stopping the fan ±
Push in the
(OFF) button.
The fan stops in automatic mode or manual mode.
If manual switching of air intake is desired ±
(AIR INTAKE) button is used to switch the air
intake between the OUTSIDE AIR mode and
RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode, the OUTSIDE
AIR mode indicator light will come on and the system will
take fresh outside air into the vehicle.
If quick circulation of cooled air is desired, press in the air
intake control button for RECIRCULATED AIR. The
RECIRCULATED AIR mode indicator light will come on.
For normal use, it is best to keep the air intake control button
Page 205 of 432

AIR CONDITIONING AND AUDIO
187
To prevent the battery from being discharged, do not leave
the car audio on longer than necessary when the engine
is not running.
To ensure the correct audio system operation:
Be careful not to spill beverages over the audio system.
Do no put anything other than a cassette tape or CD
magazine into the cassette tape slot or CD changer.
The use of cellular phone inside or near the vehicle
may cause a noise from the speakers of the audio
system which you are listening to. However, this does
not indicate a malfunction.
You can listen to the car audio when the ignition key is at
ºONº or ºACCº. However, if the engine is not running,
the key must be in the ºACCº position.
You can adjust the brightness of the display. See ºInstrument
panel light control on page 64 for details.
Audio operation is described in detail on the following pages:
Radio operation ± See page 187.
Cassette tape player operation ± See page 192.
Compact disc player operation ± See page 196.
Radio operation
(a) Listening to the radio
1. Push the
(AM) or (FM1/2) button to turn the
radio on and select either an AM or FM broadcast.
ºAMº, ºFM1º or ºFM2º will appear on the display.
The radio can also be turned on by pushing the ºPWR.VOLº
knob if the radio was being used when the system was turned
off.
2. Turn the ºPWR.VOLº knob to adjust the volume.
3. Tune in the desired station. (See º(b) Selecting a stationº.)
The radio will change automatically to stereo reception when
an FM stereo broadcast is being received. At the same time
ºSTº will appear on the display. When the receiving signal
gets weak, the channel separation will automatically be
reduced for lowest noise. If the signal becomes extremely
weak, the radio will switch over to monaural reception.
4. Adjust the tone and sound balance. (See º(d) Adjusting the
toneº and º(e) Adjusting the sound balanceº.)
5. To turn the radio off, push the ºPWR.VOLº knob.
Page 206 of 432

AIR CONDITIONING AND AUDIO
188(b) Selecting a station
Tune in the desired station using one of the following
methods. The frequency will appear on the display.
Preset tuning:
Use for tuning±in to a desired preset station.
Push the station selector button to which the desired station
has been preset. The radio will tune in to the station and the
button number will appear on the display. (See º(c) Presetting
a stationº.)
Seek tuning: Use for automatic station search and stop.
Push the
(SEEK) button and hold it until a beep is heard.
The radio will begin seeking up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, stations will be searched out one after
another.
Scan tuning: Use for scanning preset station channels or
station±to±station scanning.
Push the
(SCAN) button for longer than 1 seconds. With
ºP. SCANº blinking on the display, the radio will
automatically seek out a preset station of a higher channel
number in the AM/FM mode. If there is a preset station on the
channel, then the tuning is held for 5 seconds. If there is no
station on the channel, then the tuning is only held for 1
second. If the
(SCAN) button is pushed while listening
to a preset station channel, then the scan proceeds to the next
highest channel, proceeding in turn through the 6 channels of
FM1 and then the 6 channels of FM2, then repeating the
process. To continue listening to the channel of your choice, simply push the
(SCAN) button once again.