1999 LAND ROVER DEFENDER clutch

CLUTCH
1
REPAIR CLUTCH ASSEMBLY
Service repair no - 33.10.01.01
Remove
1.Remove gearbox assembly.See MANUAL
GEARBOX, Repair.
2.Restrain flywheel.
3.Working in sequence, loosen 6 nuts securing
clutch cover to flywheel.
4.Remove clutch cover and clutch plate.
Refit
5.Clean clutch cover and flywheel mating faces
and spigot bush in end of crankshaft.
6.Position clutch drive plate to flywheel with
’gearbox side’ facing towards gearbox.
7.PositionLRT-12-152alignment tool through
drive plate into spigot bearing in crankshaft.8.Fit clutch cover and locate on dowels.
9.Position clutch cover nuts and tighten in diagonal
sequence to25 Nm (18 lbf.ft).
10.Fit gearbox assembly.See MANUAL
GEARBOX, Repair.
ProCarManuals.com

33CLUTCH
2
REPAIR BEARING - CLUTCH RELEASE
Service repair no - 33.25.12
Remove
1.Remove gearbox assembly.See MANUAL
GEARBOX, Repair.
2.Remove retaining peg and remove release
bearing.
3.Remove bolt securing clutch release fork,
remove retaining clip and remove clutch release
fork.
Refit
4.Clean release fork.
5.Examine clutch release fork pivot points for
wear.
6.Apply a smear of Molybdenum disulphide grease
to release fork pivot points.
7.Fit retaining clip ensuring it locates over pivot
point washer.
8.Fit bolt and tighten to10 Nm (7 lbf.ft).
9.Clean release bearing and bearing sleeve
mating faces.
10.Apply smear of Molybdenum disulphide grease
to release bearing sleeve.
11.Fit release bearing and secure with retaining
peg.
12.Fit gearbox assembly.See MANUAL
GEARBOX, Repair.CLUTCH - MASTER CYLINDER LH DRIVE
Service repair no - 33.20.01
Remove
1.Remove 3 screws securing closing panel to
lower’A’post.
2.Release closing panel sufficient to gain access
to clutch and brake pedal bracket bolts.
3.Remove clutch pedal rubber.
4.Remove 12 bolts securing clutch and brake
pedal brackets to body.
ProCarManuals.com

CLUTCH
3
REPAIR
5.Disconnect multiplug from clutch pedal sensor.
6.Disconnect muliplug and harness clip from pedal
bracket.
7.Position cloth to collect fluid spillage.
8.Loosen pipe union, release pipe and plug pipe
and master cylinder.
9.Move brake master cylinder assembly aside and
lift out clutch master cylinder assembly.
10.Remove 6 screws, remove pedal box top cover
and discard gasket.
11.Remove nut securing push rod to clutch pedal
trunnion.
12.Remove 2 bolts and remove clutch master
cylinder from pedal bracket.
13.Remove clutch pedal sensor and pipe union
from master cylinder and discard sealing
washers.Refit
14.Clean sensor and pipe union.
15.Fit clutch pedal sensor and pipe to master
cylinder using new sealing washers.
16.Position master cylinder to pedal bracket and
align push rod to pedal trunnion.
17.Fit bolts and nuts and secure master cylinder to
pedal bracket.
18.Fit nut securing push rod to clutch pedal trunnion
but do not tighten nut at this stage.
19.Move brake master cylinder aside and position
clutch master cylinder assembly.
20.Clean clutch pipe union.
21.Align pipe and tighten union.
22.Connect multiplug to clutch pedal sensor.
23.Tighten bolts securing clutch pedal and brake
pedal brackets to body.
24.Fit clutch pedal rubber.
25.Position closing panel and tighten screws to
lower’A’post.
ProCarManuals.com

33CLUTCH
4
REPAIR Clutch pedal setting
1.Loosen both locknuts on master cylinder push
rod.
2.Check distance from lower edge of clutch pedal
to floor. Correct measurement is 140 mm (5.50
in) without floor mat.
3.Adjust pedal stop to obtain correct setting.
4.Adjust master cylinder push rod to obtain
approximately 1.5 mm (0.06 in) free play
between push rod and master cylinder piston.
5.Tighten push rod locknuts.
6.Check operation of clutch pedal and ensure that
there is minimum of 6 mm (0.25in) of free play
before pressure is felt.
7.Fit pedal box top cover and multiplug bracket
using a new gasket and secure with screws.
8.Connect multiplug and harness clip to pedal
bracket.
9.Bleed clutch hydraulic system.See
Adjustment.CYLINDER - CLUTCH SLAVE
Service repair no - 33.35.01
Remove
1.Disconnect pipe from slave cylinder.
CAUTION: Plug the connections.
2.Position container to catch spillage.
3.Remove 2 bolts securing slave cylinder to bell
housing.
4.Withdraw slave cylinder from bell housing and
push rod.
Refit
5.Clean ends of pipes, bell housing and slave
cylinder mating faces.
6.Lubricate end of push rod with Molybdenum
disulphide gease.
7.Locate slave cylinder to push rod and bell
housing.
8.Fit bolts and tighten to25 Nm (18 lbf.ft).
9.Connect clutch pipe to slave clyinder.
10.Bleed clutch system.See Adjustment.
ProCarManuals.com

MANUAL GEARBOX
1
REPAIR COVER - FRONT - RESEAL AND FIT NEW INPUT
SHAFT OIL SEAL
Service repair no - 37.12.33.01
Remove
1.Remove gearbox.See this Section.
2.Remove retaining peg and remove release
bearing.
3.Remove bolt securing clutch release fork,
remove retaining clip and remove clutch release
fork.
4.Remove 2 bolts securing release bearing sleeve,
remove bearing sleeve.
5.Remove 6 bolts securing clutch housing, remove
housing.
6.Remove and discard 6 bolts securing front
cover, remove cover.
ProCarManuals.com

37MANUAL GEARBOX
2
REPAIR
7.Using a soft metal drift, carefully remove input
shaft front bearing track from front cover.
CAUTION: Take care not to damage
bearing track, if track is damaged, it will be
necessary to fit a new input shaft front
bearing.
8.Remove input shaft oil seal from front cover;
discard oil seal.
Refit
9.Using a suitable solvent clean seal recess, front
cover and gearbox mating faces; clean threads
of bolts and bolt holes.
10.Clean bearings and bearing races.
11.Lubricate a new oil seal with gearbox oil.
12.Fit oil seal using a suitable mandrel.
13.Fit input shaft front bearing track using a press
and suitable mandrel.
14.Apply sealant, Part No. STC 4404 to front cover.
15.Position front cover, apply Loctite 290 to threads
of bolts; fit new bolts and tighten by diagonal
selection to25 Nm (18 lbf.ft).
16.Clean clutch housing mating faces, dowels and
dowel holes.
17.Position clutch housing, fit bolts and tighten by
diagonal selection to75 Nm (55 lbf.ft).
18.Clean bearing sleeve mating faces, dowel and
dowel holes.
19.Position bearing sleeve, fit bolts and tighten to
25 Nm (18 lbf.ft).
20.Examine clutch release fork pivot points for wear
and replace as required.
21.Apply a smear of Molybdenum disulphide grease
to pivot points and position release fork.
22.Fit retaining clip ensuring it locates over pivot
point washer, fit bolt and tighten to10 Nm (7
lbf.ft).23.Clean release bearing and bearing sleeve
mating faces.
24.Apply smear of Molybdenum disulphide grease
to release bearing sleeve.
25.Fit release bearing and secure with retaining
peg.
26.Fit gearbox.See this Section.
ProCarManuals.com

37MANUAL GEARBOX
8
REPAIR
12.Remove 13 screws securing tunnel cover.
13.Release and remove tunnel cover.
14.Remove cooling fan.See COOLING SYSTEM,
Repair.
15.Remove air filter.See FUEL SYSTEM, Repair.
16.Remove 2 upper bolts securing clutch housing to
engine.
17.Remove bolt securing shim to clutch housing.
18.Release gearbox breather pipes from clips on
heater hose.
19.Remove starter motor.See ELECTRICAL,
Repair.
20.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
21.Drain gearbox oil.See Adjustment.
22.Drain transfer gearbox oil.See
MAINTENANCE ,
23.Remove 3 nuts securing intermediate silencer to
tail pipe.
24.Release silencer from mounting rubbers, remove
silencer and discard gasket.
25.Mark front and rear propeller shaft to transfer
gearbox flanges for reassembly purposes.
ProCarManuals.com

MANUAL GEARBOX
9
REPAIR
26.Remove 4 nuts securing front propeller shaft to
transfer gearbox, release propeller shaft from
output drive flange.
27.Remove 4 nuts, release rear propeller shaft from
brake drum.
28.Remove 2 bolts securing clutch slave cylinder,
release slave cylinder and position aside.
29.Fit support plateLRT-99-007to gearbox jack.
30.Position gearbox jack and support plate to
gearbox and secure with 3 bolts.
31.Support the weight of gearbox.
32.Remove 4 nuts securing LH and RH mountings
to chassis and transfer gearbox mounting
brackets.
33.Remove bolts securing mountings to gearbox,
raise gearbox and remove both mountings and
heat shield from LH mounting and brackets.
ProCarManuals.com