1999 LAND ROVER DEFENDER lock

10MAINTENANCE
10
MAINTENANCE DOOR LOCKS AND HINGES
Front, rear and tail doors
1.Open each door in turn and lubricate door
hinges and check strap using recommended
lubricant.
2.Lubricate door lock, striker and private lock using
PTFE lubricant. Remove excessive lubricant,
particularly from door striker area, to avoid
customer complaint.
3.Check tightness of accessible door lock and
striker fixings
4.Open and close door to check for smooth,
noise-free operation. Ensure door closes
securely.
5.Check for smooth operation of private lock.
Bonnet
1.With bonnet open, lubricate hinges, striker, lock
and safety catch using a suitable lubricant.ENGINE COOLANT
1.Renew engine coolant.See COOLING
SYSTEM, Adjustment.
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com

12 - ENGINE
CONTENTS
Page
DESCRIPTION AND OPERATION
TD5 ENGINE 1........................................................................................................
GENERAL 12..........................................................................................................
CYLINDER BLOCK 13............................................................................................
CRANKSHAFT, SUMP AND OIL PUMP 22............................................................
CYLINDER HEAD COMPONENTS 25...................................................................
CAMSHAFT COVER COMPONENTS 30...............................................................
CAMSHAFT TIMING CHAIN COMPONENTS 30...................................................
CYLINDER BLOCK FLOW 32.................................................................................
OIL COOLER / FILTER FLOW 34...........................................................................
CYLINDER HEAD FLOW 36...................................................................................
ADJUSTMENT
ENGINE OIL PRESSURE CHECK 1......................................................................
REPAIR
CAMSHAFT 1.........................................................................................................
PULLEY - CRANKSHAFT 3....................................................................................
OIL SEAL - CRANKSHAFT - REAR 4.....................................................................
BEARING - SPIGOT - CRANKSHAFT 5.................................................................
GASKET - CYLINDER HEAD 6..............................................................................
ROCKER SHAFT ASSEMBLY 11...........................................................................
GASKET - COVER - CAMSHAFT 13......................................................................
ENGINE AND ANCILLARIES 14.............................................................................
MOUNTING - FRONT - LH 19................................................................................
MOUNTING - FRONT - RH 20................................................................................
MOUNTING - GEARBOX - REAR - LH 21..............................................................
MOUNTING - GEARBOX - REAR - RH 22.............................................................
FLYWHEEL 22........................................................................................................
FILTER - OIL 23......................................................................................................
STRAINER - OIL PICK-UP 24.................................................................................
PUMP - OIL 24........................................................................................................
GASKET - ENGINE TO SUMP 26..........................................................................
SWITCH - OIL PRESSURE 28...............................................................................
VALVE - RELIEF - OIL PRESSURE 29..................................................................
COOLER - ENGINE OIL 29....................................................................................
CENTRIFUGE ASSEMBLY 30................................................................................
ROTOR - CENTRIFUGE 32....................................................................................
ProCarManuals.com

12ENGINE
2
DESCRIPTION AND OPERATION Cylinder block components
ProCarManuals.com

ENGINE
3
DESCRIPTION AND OPERATION 1.Oil dipstick tube
2.Screw - oil dipstick tube to camshaft carrier
3.Oil dipstick
4.2nd piston ring
5.Piston
6.Small-end bush
7.Connecting rod
8.Big-end bearing cap
9.Connecting rod bolt (2 off per connecting rod)
10.Top piston ring
11.Oil control ring
12.Circlips (2 off per gudgeon pin)
13.Gudgeon pin
14.Big-end bearing shells
15.Dowels to cylinder head (2 off)
16.Gearbox shim plate
17.Rear crankshaft seal and housing
18.Screws - crankshaft seal flange to engine block (5 off)
19.Bolts - Gearbox shim plate to cylinder block (2 off)
20.Main oil gallery plug (rear)
21.Oil filter adaptor gasket
22.Oil filter adaptor thermostat
23.Oil filter adaptor assembly
24.Oil filter adaptor insert
25.Oil filter adaptor to cylinder block bolts (3 off)
26.Oil filter
27.Oil pressure switch
28.Oil cooler banjo bolts (2 off)
29.O-rings - oil cooler banjo bolts (2 off)
30.Oil cooler to cylinder block bolts (7 off)
31.Centrifuge assembly
32.Centrifuge to cylinder block bolts (3 off)
33.Centrifuge oil drain pipe
34.Oil drain pipe to sump gasket
35.Centrifuge to oil drain pipe gasket
36.Oil cooler plugs (3 off)
37.Oil cooler assembly
38.Oil cooler matrix ’O’ rings (2 off)
39.Oil cooler matrix
40.Oil cooler gasket
41.Coolant and PAS pump assembly bracket
42.Bracket bolts (5 off + 1 stud/nut)
43.Cylinder block
44.Dowels - timing chain cover (2 off)
45.Oil gallery delivery plug
46.Cross drilling plug
47.Coolant jacket plug
48.Core plugs (3 off)
ProCarManuals.com

ENGINE
5
DESCRIPTION AND OPERATION 1.Crankshaft pulley bolt
2.TV Damper to crankshaft pulley bolts (3 off)
3.TV Damper
4.Crankshaft pulley
5.Woodruff key
6.Crankshaft
7.Crankshaft to flywheel dowel
8.Spigot bush
9.Flywheel to crankshaft bolts (8 off)
10.Flywheel assembly
11.Main bearing shells (6 pairs)
12.Main bearing caps (6 off)
13.Main bearing cap bolts (12 off)
14.Thrust washer (2 off at No. 3 Main bearing)
15.Piston lubrication jets (5 off)
16.Piston lubrication jet cap head screw (5 off)
17.Stiffener plate (oil pump integral)
18.Stiffener plate / oil pump assembly to cylinder block bolts (22 off)
19.Oil pick-up pipe O-ring
20.Oil pick-up pipe inserts (2 x 6mm; 1 x 10mm)
21.Upper oil pick-up pipe
22.Oil pick-up pipe gauze
23.Lower oil pick-up pipe
24.Sump
25.Oil drain plug seal
26.Oil drain plug
27.Sump to cylinder block bolts (20 off)
28.Sump gasket
29.Oil pick-up pipe bolts (3 off)
30.Oil pump
31.Chain lubrication jet
32.Chain lubrication jet screw
33.Stiffener to cylinder block dowel (2 off)
ProCarManuals.com

ENGINE
7
DESCRIPTION AND OPERATION 1.Camshaft carrier
2.Dowel - rocker shaft to camshaft carrier (1 off)
3.Cylinder head bolts (12 off)
4.Rocker shaft to camshaft carrier bolts (6 off)
5.Rocker shaft
6.Circlips (10 off)
7.EUI Rocker arms (5 off)
8.Camshaft carrier to cylinder head screws (13 off)
9.Finger follower (10 off)
10.Valve spring collets (20 off)
11.Lash adjuster (10 off)
12.Valve spring retainer (10 off)
13.Valve spring (10 off)
14.Valve stem seal (10 off)
15.Valve guide (10 off)
16.Valve seat insert (10 off)
17.Inlet valve (5 off)
18.Exhaust valve (5 off)
19.Camshaft
20.Camshaft bore seal (rear)
21.Coolant jacket core plug
22.Cylinder head block
23.Water jacket threaded plug
24.Engine lifting bracket (LH)
25.Engine lifting bracket bolts (2 off)
26.Coolant outlet elbow to cylinder head bolts (3 off)
27.Coolant outlet elbow
28.Coolant outlet elbow gasket
29.Cylinder head gasket
30.Non-return valve (not removable, integral in cylinder head)
31.Camshaft bore end cap (front)
32.End cap seal
33.Cylinder head to cam carrier dowel (2 off)
34.Engine lifting bracket (RH)
35.Engine lifting bracket bolts (2 off)
ProCarManuals.com

ENGINE
11
DESCRIPTION AND OPERATION 1.Vacuum pump stub pipe
2.Cylinder head to timing chain cover bolt
3.Cylinder head to timing chain cover nut
4.Cylinder head to timing chain cover stud
5.Tensioner assembly pivot screw
6.Tensioner adjuster
7.Tensioner arm assembly
8.Duplex timing chain - crankshaft to camshaft sprocket
9.Camshaft sprocket bolts (3 off)
10.Camshaft sprocket
11.Fixed chain guide
12.Fixed guide pin
13.Fixed chain guide to cylinder block screws
14.Oil pump drive chain
15.Oil pump sprocket
16.Oil pump sprocket screw
17.Crankshaft sprockets
18.Bearing to viscous fan shaft
19.Viscous fan to cover bearing
20.Circlip
21.Hub - viscous fan to bearing flange
22.Timing chain cover
23.Timing chain cover to crankshaft seal
24.Timing chain to cylinder head screws (8 off)
ProCarManuals.com