1999 LAND ROVER DEFENDER ECU

76CHASSIS AND BODY
8
REPAIR LINER - FRONT WHEEL ARCH
Service repair no - 76.10.48
Remove
1.Raise front of vehicle.
WARNING: Support on safety stands.
2.Remove front wheel.
3.Support axle weight with jack.
4.Remove 6 screws securing damper top cover to
inner wing, remove cover.
5.Remove nut securing damper to top mounting
bracket and collect rubber bush and 2 washers.
6.Remove 4 nuts securing damper to mounting
bracket and collect washers.
7.Remove damper top cover.
8.Remove 4 screws and 3 studs securing liner to
inner wing. Remove liner.
Refit
9.Position liner, secure with screws and studs.
10.Fit damper mounting bracket and tighten nuts.
11.Position damper to mounting bracket, fit rubber
bush and washers and tighten nut.
12.Fit damper cover to inner wing and secure with
screws.
13.Fit road wheel.
14.Remove stands and lower vehicle.
ProCarManuals.com

CHASSIS AND BODY
9
REPAIR FRONT BUMPER
Service repair no - 76.22.08
Remove
1.Remove 6 screws and remove front grille.
2.Remove 4 through bolts securing front bumper
to chassis longitudinals.
3.Remove front bumper.
Refit
4.Fit front bumper to chassis longitudinals and
secure with bolts.
5.Fit front grille and secure with screws.DOOR - REAR
Service repair no - 76.28.02.99
Remove
1.Remove nut securing door check strap.
2.With assistance remove 4 bolts securing door to
body and remove door.
Refit
3.With assistance position door and fit but do not
tighten bolts.
4.Align door to body aperture and tighten bolts.
5.Fit and tighten check strap nut.
ProCarManuals.com

76CHASSIS AND BODY
10
REPAIR DOOR - TAIL - REMOVE
Service repair no - 76.28.19.99
Remove
1.Remove 3 nuts and remove spare wheel.
2.Remove bolt securing check strap to body.
3.Release harness grommet from harness cover,
disconnect connectors and multiplug.
4.Release harness cover and harness from body.
5.With assistance, remove 6 screws securing door
hinges to body and remove door.
Refit
6.With assistance, position door and fit but do not
tighten bolts.
7.Position check strap and tighten bolt.
8.Align door to body and tighten bolts.
9.Position harness through body and secure
harness cover.
10.Secure harness connectors and multiplug.
11.Secure harness grommet to body.
12.Position spare wheel to tail door and tighten
nuts.
ProCarManuals.com

CHASSIS AND BODY
11
REPAIR GLASS/SEALING RUBBER - TAIL DOOR - UP TO
02MY
Service repair no - 76.31.22
Remove
1.Remove high level stop lamp.See
ELECTRICAL, Repair.
2.Remove 3 nuts and remove spare wheel.
3.Raise cover, remove nut and remove rear wiper
arm assembly.
4.Disconnect 2 HRW Lucars.
5.Remove 30 screws securing door glass
retainers.
6.Remove door glass retainers.
7.Remove door glass sealing strips.
8.Release and remove door glass.Refit
9.Clean old sealant from glass aperture.
10.Apply sealant to glass aperture.
11.Position door glass, fit sealing strips and glass
retainers and secure with screws.
12.Connect HRW lucars.
13.Fit high level stop lamp.See ELECTRICAL,
Repair.
14.Fit rear wiper arm assembly and secure with nut.
15.Position spare wheel and secure with nuts.
ProCarManuals.com

76CHASSIS AND BODY
12
REPAIR SEAT BELT - FRONT
Service repair no - 76.73.13
Remove
1.Remove cap from seat belt guide bolt.
2.Remove bolt securing seat belt guide to’B’post.
3.Release belt from’B’post mounting.
4.Remove 3 bolts securing belt bracket to seat
base.
5.Remove 2 studs securing seat belt retaining clip.
6.Remove retaining clip.
7.Remove bolt securing inertia reel to body.
8.Remove automatic belt assembly.
9.Remove 2 bolts securing stalk to body.
10.Remove stalk.
Refit
11.Position stalk and tighten bolts.
12.Position automatic belt assembly to body and
tighten bolt to38 Nm
13.Unreel portion of belt.
14.Position bracket to seat base, tighten bolts.
15.Position belt to’B’post mounting and tighten bolt
to32 Nm (24 lbf.ft).
16.Fit cap to bolt head.
17.Position belt retaining clip to seat base and
secure with studs.
ProCarManuals.com

CHASSIS AND BODY
13
REPAIR SEAT BELT - CENTRE - REAR
Service repair no - 76.73.20
Remove
1.Remove seat belt bolt caps and remove bolts.
2.Remove seat belt and stalk.
Refit
3.Position seat belt and stalk.
4.Fit and tighten bolts to32 Nm (24 lbf.ft),and fit
bolt caps.SEAT BELT - REAR - SIDE
Service repair no - 76.73.23
Remove
1.Remove cap from seat belt guide bolt.
2.Remove seat belt upper and lower securing
bolts.
3.Remove seat belt guide from’D’post finisher.
4.Remove 2 studs securing finisher to’D’post.
ProCarManuals.com

76CHASSIS AND BODY
14
REPAIR
5.Release finisher from body upper rail and’D’
post.
6.Pull seat belt through’D’post finisher.
7.Remove bolt securing seat belt to’D’post and
remove belt assembly.
Refit
8.Position seat belt assembly to’D’post and
tighten bolt to32 Nm (24 lbf.ft).
9.Extend seat belt and position through’D’post
finisher.
10.Fit and tighten seat belt upper and lower
securing bolts to32 Nm (24 lbf.ft).
11.Secure’D’post finisher to body upper rail.
12.Fit belt guide to’D’post finisher and fit finisher
retaining studs.
13.Fit cap to seat belt bolt.SEAT - REAR
Service repair no - 78.10.48.99
Remove
1.Remove bolts securing rear seat to hinges and
collect spacer.
2.Remove rear seat.
Refit
3.Position rear seat and align to hinges.
4.Fit spacer and tighten bolts.
ProCarManuals.com

CHASSIS AND BODY
15
REPAIR COVER - CUSHION - REAR SEAT
Service repair no - 78.40.04
Remove
1.Remove rear seat.See this Section.
2.Remove 2 bolts securing squab to cushion
frame.
3.Remove squab and collect spacer.
4.Remove 17 screws securing base board to seat
cushion frame and remove board.
5.Remove 2 trim retaining clips.
6.Release cover retainers from seat frame.
7.Remove cover from cushion pad.
Refit
8.Position cover to cushion pad and secure
retainers to seat frame.
9.Fit trim retaining clips.
10.Position base board and tighten screws.
11.Position and align squab to cushion frame.
12.Fit spacer and tighten securing bolts.
13.Fit rear seat.See this Section.
ProCarManuals.com