1999 LAND ROVER DEFENDER fuel cap

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use Texaco XLC long life coolant. Use one part anti-freeze to one part water for
protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below 50% anti-freeze otherwise
damage to engine is liable to occur. Maximun concentration is 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil ND-OIL 8
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze, windscreen washer additives, lubricants and various adhesives.
ProCarManuals.com

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Pints
Engine sump oil - Td5 7.20...................................................... 12.67
Extra when refilling after fitting new filter 1.00.......................... 1.76
Manual gearbox 2.38............................................................... 4.19
Transfer gearbox oil 2.30......................................................... 4.00
Front differential 1.70............................................................... 3.00
Rear differential
90 Models 1.70............................................................... 3.00
110 Models 2.26............................................................. 4.00
Power steering box and reservoir LHD 2.90............................ 5.00
Power steering box and reservoir RHD 3.40............................ 6.00
Swivel pin housing oil/grease (each) 0.35................................ 0.60
Fuel tank usable fuel
90 Models 60.00............................................................... 13.20 gall
110 & 130 Models 75.00................................................... 16.50 gall
Cooling system - Td5 13.00....................................................... 22.88
Washer bottle 3,0................................................................... 5.28
NOTE: * All levels must be checked by dipstick or level plugs as applicable.
ANTI-FREEZE
PERCENTAGE CONCENTRATION - 50%
PROTECTION - LOWER TEMPERATURE LIMIT
Complete protection
Vehicle may be driven away immediately from cold,
-33°C (-36°F).
Safe limit protection
Coolant in semi-frozen state. Engine may be started
and driven away after warm-up period, -41°C (-42°
F).
Lower protection
Prevents frost damage to cylinder head, block and
radiator. Thaw out before starting engine, -47°C (-53°
F).
CAUTION: Anti-freeze content must never
be allowed to fall below 50% otherwise
damage to the engine is liable to occur.
Also, anti-freeze content should not exceed 60%
as this will greatly reduce the cooling effect of the
coolant.RECOMMENDED FUEL
Diesel fuel oil, distillate, diesel fuel, automotive gas or
Derv to British standard 2869, Class A1 or A2
Using diesel fuel with a class rating lower than stated
above could seriously impair vehicle performance.
ProCarManuals.com

MAINTENANCE
9
MAINTENANCE INTERCOOLER / COOLING SYSTEM
1.Visually check for any obstructions in the
radiator and intercooler matrix and remove
debris as necessary.
2.Visually check fan blades for damage.
3.Check cooling, intercooler and heating systems
for leaks, hoses and oil pipes for security and
condition.
4.Check accessible hose clips for tightness.
5.Check coolant level, top-up if necessary
Cooling System Top-Up
1.With engine cold, remove expansion tank filler
cap.
2.Top-up with recommended mixture of coolant
until level reaches mark on expansion tank.
3.Fit expansion tank filler cap.
Intercooler Flush
1.Remove intercooler.See FUEL SYSTEM,
Repair.
2.Flush intercooler element using Unicorn
Chemicals’C’Solve following the manufaturers
instructions.
3.Thoroughly dry intercooler ensuring that no trace
of solvent remains in the element.
4.Refit intercooler.See FUEL SYSTEM, Repair.AMBIENT AIR PRESSURE (AAP) SENSOR - Td5
1.Check ambient air pressure sensor for damage.
ProCarManuals.com

19FUEL SYSTEM
2
DESCRIPTION AND OPERATION DESCRIPTION
General
The fuel delivery system comprises a fuel tank, fuel pump, fuel pressure regulator, five injectors and a fuel filter.
The system is controlled by the ECM, which energises the fuel pump relay and controls the operation and timing
of each injector solenoid.
Unlike other Diesel engines, the Td5 has no injection pump. The diesel direct injection system receives fuel at
pressure from a two stage fuel pump located in the fuel tank. The system incorporates a fuel return to the fuel
pump, via a fuel cooler attached to the inlet manifold, and a fuel filter. A fuel pressure regulator is located in a
housing on the rear of the cylinder head. The regulator maintains the fuel delivered to the injectors at a constant
pressure and returns excess fuel back to the fuel filter and pump via the fuel cooler.
A fuel filter is positioned on the chassis longitudinal, below the RH rear wheel arch. The fuel feed and return to and
from the engine passes through the filter. The filter also incorporates a water sensor, which illuminates a warning
lamp in the instrument pack.
A moulded fuel tank is located at the rear underside of the vehicle between the chassis longitudinals. The tank
provides the attachment for the fuel pump and the fuel gauge sender unit, which is located inside the tank.
Fuel Tank and Breather
The fuel tank and breather system is a major part of the fuel delivery system. The fuel tank and breathers are
located at the rear of the vehicle between the chassis longitudinals.
Fuel Tank
The moulded fuel tank is made from High Molecular Weight (HMW) High Density Polyethylene (HDPE), and is
manufactured using a proportion of recycled plastic.
The tank is held in position by a metal cradle which is secured to the chassis cross members by four bolts, two
holding the front of the cradle in position, two holding the rear. The fuel tank has a useable capacity of 75 litres
(16.5 gallons).
An aperture in the top surface of the tank allows for the fitment of the fuel pump and fuel gauge sender unit, which
is retained with a locking ring. A reflective metallic covering is attached to the tank with three scrivets to shield the
tank from heat generated by the exhaust system.
Fuel Tank Breather System
The fuel tank filler tube incorporates a tank vent which allows air and fuel vapour displaced from the tank when
filling to vent to atmosphere via the filler neck.
A breather spout within the tank controls the tank’Full’height. When fuel covers the spout it prevents fuel vapour
and air from escaping from the tank. This causes the fuel to’back-up’in the filler tube and shuts off the filler gun.
The position of the spout ensures that when the filler gun shuts off, a vapour space of approximately 10% of the
tanks total capacity remains. The vapour space ensures that the Roll Over Value (ROV) is always above the fuel
level and vapour can escape and allow the tank to breathe.
The ROV is welded to the top surface of the tank. It is connected by a tube to the filler tube, which in turn is
connected to the atmospheric vent pipe. The ROV allows fuel vapour to pass through it during normal vehicle
operation. In the event of the vehicle being overturned the valve shuts off, sealing the tank and preventing fuel
from spilling from the atmospheric vent pipe.
ProCarManuals.com

FUEL SYSTEM
7
DESCRIPTION AND OPERATION INJECTORS
1.Solenoid housing
2.Electrical connector
3.Push rod socket
4.Push rod return spring
5.Housing
6.Fuel delivery port7.Fuel return port
8.Nozzle cap nut
9.Copper washer
10.Nozzle
11.’O’ring
12.Cap screw
The five injectors are located in the cylinder head adjacent the camshaft, with the nozzle of each injector
protruding directly into the cylinder. Each injector is sealed into the cylinder head with a’O’ring and copper
washer and secured with a clamp and bolt.
Each injector is operated mechanically by an overhead camshaft and rocker, and electrically by a solenoid
controlled by the ECM. Each injector is supplied with pressurised fuel from the pump via the regulator housing and
internal drillings in the cylinder head.
The solenoid housing is secured to the injector body with two cap screws and is a sealed unit. It has a two pin
electrical connector on its top face.
The injector body is machined from a forging. The body has a machined central bore which locates the push rod.
A thread on the outer diameter provides the attachment for the nozzle cap nut. The body also provides attachment
for the solenoid housing.
ProCarManuals.com

19FUEL SYSTEM
8
DESCRIPTION AND OPERATION The injector push rod is operated from the rocker and cam assembly by a sprocket. The push rod is located in the
housing bore and retained in its extended position by a push rod return spring. The powerful spring ensures that
the push rod socket is always in contact with the rocking lever and the cam.
The lower part of the injector housing locates the spring loaded nozzle. The nozzle is retained in the housing by a
nozzle cap nut which is screwed onto the housing. The nozzle cap nut has four holes around its circumference
which connect to the fuel pump drilling in the cylinder head. The injector housing has ports located above the
nozzle cap nut which connect with the fuel delivery drilling in the cylinder head. An’O’ring seals the injector in the
machined location in the cylinder head and a copper washer seals the injector from the combustion chamber.
The injectors are supplied with pressurised fuel from the fuel pump via the pressure regulator housing and internal
drillings in the cylinder head. Each injector sprays fuel directly into the cylinder at approximately 1500 bar (22000
lbf.in) atomising the fuel and mixing it with intake air prior to combustion.
The camshaft and rocker arrangement depresses the push rod which pressurises the fuel within the injector.
When the injector is required to inject fuel into the cylinder, the ECM energises the solenoid which closes a valve
within the solenoid housing. The closure of the valve stops the fuel entering the return line to the pump, trapping it
in the injector. The compression of the fuel by the push rod causes rapid pressurisation of the fuel which lifts the
injector nozzle, forcing the fuel into the cylinder at high pressure. The ECM controls the injection timing by altering
the time at which the solenoid is energised and the injection period by controlling the period for which the solenoid
is energised.
ProCarManuals.com

19FUEL SYSTEM
2
ADJUSTMENT FUEL TANK - DRAIN
Service repair no - 19.55.02
1.Remove battery cover.
2.Disconnect both leads from battery, earth lead
first.
WARNING: Fuel vapour is highly
flammable and in contained spaces is also
explosive and toxic. Always have a fire
extinguisher containing FOAM, CO2, GAS OR
POWDER close at hand when handling or draining
fuel.
3.Using a fuel recovery appliance, drain the fuel
from the tank into a sealed container. Follow the
manufacturers instructions for the connection
and safe use of the appliance.
4.Remove filler cap and insert hose into filler neck.
5.Connect bowser earth line. Drain fuel.
6.Connect battery leads.
7.Fit battery cover.
ProCarManuals.com

COOLING SYSTEM
3
DESCRIPTION AND OPERATION
NOTE: Inset A shows differences for Pre
EU3 models
1.Pressure cap
2.Overflow pipe
3.Heater return hose
4.Heater matrix
5.Heater inlet hose
6.Oil cooler return pipe - EU3 models
7.Connecting hose
8.Oil cooler housing assembly
9.Heater inlet pipe
10.Connecting hose
11.Outlet housing
12.Engine Coolant Temperature (ECT) sensor
13.Bleed screw
14.Radiator top hose
15.Radiator - upper
16.Intercooler
17.Gearbox oil cooler
18.Radiator - lower
19.Viscous fan
20.Drain plug
21.Connecting hose
22.Fuel cooler feed hose
23.Radiator bottom hose
24.Thermostat housing
25.Connecting hose
26.Coolant pump feed pipe
27.Coolant by-pass pipe
28.Radiator bleed pipe
29.Connecting hose
30.Coolant pump
31.Fuel cooler
32.Heater/expansion tank return hose
33.Expansion tank
34.EGR Cooler - EU3 models
35.Connecting hose - EU3 models
36.Connecting hose - EU3 models
37.Hose - EGR Cooler to oil cooler return pipe -
EU3 models
38.Radiator lower feed hose - Pre EU3 models
39.Oil cooler return pipe - Pre EU3 models
ProCarManuals.com