1999 LAND ROVER DEFENDER brake light

TRANSFER GEARBOX
5
REPAIR
43.If transfer gearbox is to be refitted, remove and
discard input shaft oil seal.
Refit
44.Clean mating faces of main gearbox extension
case and transfer gearbox.
45.Remove all traces of sealant from threads of
transfer gearbox securing bolts and studs.
46.Clean input shaft oil seal recess in transfer
gearbox.
47.Lubricate new input shaft oil seal with transfer
gearbox oil.
48.Using toolLRT-37-014, fit input shaft oil seal, lip
side facing inwards.49.Ensure guide studsLRT-41-009are fitted in
main gearbox extension case.
CAUTION: If securing studs were removed
during transfer gearbox removal, apply
Loctite 290 to threads of new studs; fit
studs and tighten to 45 Nm (33 lbf.ft).
50.Secure transfer gearbox to support plate
LRT-99-010, fit and tighten 4 bolts.
51.Raise transmission hoist until transfer gearbox
can be located over guide studsLRT-41-009.
52.Apply Loctite 290 to threads of securing bolts
and studs.
53.Fit and lightly tighten 2 nuts to secure transfer
gearbox to main gearbox extension case.
54.Remove guide studsLRT-41-009.
55.Ensuring bolts are in their original fitted
locations, fit and lightly tighten 4 bolts to secure
transfer gearbox to main gearbox extension
case.
56.Progressively tighten nuts and bolts to45 Nm
(33 lbf.ft).
57.Position earth leads to RH side of transfer
gearbox, fit and tighten bolt.
58.Connect low ratio detect switch multiplug and
secure to bracket. Connect Lucars to differential
lock warning lamp switch.
59.Raise gearbox jack and guide transfer gearbox
lever through tunnel.
60.Connect body harness clips to bracket on top of
transfer gearbox.
61.Position earth lead to transfer gearbox, tighten
nut to45 Nm (33 lbf.ft).
62.Connect speed sensor multiplug and secure
harness in clip.
63.Position heat shield to LH mounting, fit
mountings and brackets and tighten bolts to85
Nm (63 lbf.ft).
64.Fit nuts securing RH and LH mountings and
tighten to48 Nm (35 lbf.ft).
65.Position breather pipe to transfer gear box, fit
new sealing washers and tighten banjo bolts to
15 Nm (11 lbf.ft).
66.Remove bolts securing support plate to gearbox
jack.
67.Remove bolts securingLRT-99-010to transfer
gearbox.
68.Apply Loctite 290 to threads of bottom cover
securing bolts, fit bolts and tighten to25 Nm (18
lbf.ft)
69.Position differential lock control rod and secure
with retaining clip.
70.Clean rear propeller shaft to brake drum flange
mating faces.
ProCarManuals.com

70 - BRAKES
CONTENTS
Page
DESCRIPTION AND OPERATION
REAR BRAKE CALIPERS - FROM 02MY 2...........................................................
ADJUSTMENT
BRAKE SYSTEM BLEED 1.....................................................................................
PARK BRAKE - ADJUST 2.....................................................................................
REPAIR
ECU - ABS 1...........................................................................................................
SENSOR - ABS - FRONT WHEEL 2......................................................................
SENSORS - ABS - REAR WHEELS 3....................................................................
MASTER CYLINDER 4...........................................................................................
SERVO ASSEMBLY 5............................................................................................
MODULATOR UNIT - ABS 6...................................................................................
BRAKE CALIPER - FRONT 7.................................................................................
BRAKE CALIPER - REAR 8....................................................................................
SWITCH - STOP LIGHT 9.......................................................................................
FRONT BRAKE PADS - FROM 02MY 10...............................................................
REAR BRAKE PADS - FROM 02MY 11.................................................................
ProCarManuals.com

BRAKES
5
REPAIR SERVO ASSEMBLY
Service repair no - 70.50.01
Remove
Before starting, refer to general brake service
practice.See Adjustment.
NOTE: The non-return valve and grommet
are the only serviceable components. In
event of failure or damage, fit a new unit.
1.Remove master cylinder.See this Section.
2.Release vacuum hose from servo.
3.Disconnect brake light switch Lucars.
4.Remove 3 screws securing closing panel to
lower’A’post.
5.Release closing panel sufficient to gain access
to brake pedal return springs.
6.Release 2 brake pedal return springs from brake
pedal.
7.Remove blanking grommets from either side of
pedal box.
8.Remove split pin and clevis pin securing servo
push rod to brake pedal.
9.Remove 2 nuts securing servo to pedal box.
10.Remove servo assembly and rubber washer
from pedal box.
ProCarManuals.com

70BRAKES
8
REPAIR Refit
14.Clean caliper to hub mating faces.
15.Position caliper to hub, fit bolts and tighten to82
Nm (60 lbf.ft).
16.Remove plugs from pipe to caliper connections
and wipe.
17.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
18.Apply a light film of grease to rear of brake pads.
19.Fit pads to calipers.
From 02MY, ensure pads are correctly fitted,
with leading edge chamfer fitted as shown.
20.Fit pad retainers and springs.
21.Fit split pins to retainers.
22.Remove brake hose clamp.
23.Bleed brakes.See Adjustment.
24.Depress brake pedal to seat pads onto discs.
25.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).BRAKE CALIPER - REAR
Service repair no - 70.55.03
Remove
1.Loosen rear road wheel nuts.
2.Raise rear of vehicle.
WARNING: Support on safety stands.
3.Remove road wheel.
4.Remove split pins from brake pad retaining pins.
5.Remove brake pad retaining pins.
6.Remove brake pad retainer springs.
7.Remove brake pads and shim if fitted.
8.Position container beneath brake caliper to
collect spillage.
9.Loosen brake pipe union and disconnect from
caliper.
CAUTION: Plug the connections.
10.Remove 2 bolts securing caliper.
11.Remove brake caliper.
ProCarManuals.com

BRAKES
9
REPAIR Refit
12.Clean caliper to axle bracket mating faces.
13.Position caliper to axle bracket, fit bolts and
tighten to82 Nm (60 lbf.ft).
14.Remove plugs from pipe and caliper.
15.Clean brake pipe union and caliper.
16.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
17.Apply a light film of grease to rear of brake pads.
18.Fit brake pads.
From 02MY, ensure shims are correctly fitted,
see illustration.
NOTE: Vehicles from 02MY have leading
and trailing edge chamfers on rear pads.
19.Fit pad retainer springs.
20.Fit brake pad retaining pins and secure with new
split pins.
21.Bleed brakes.See Adjustment.
22.Depress brake pedal to seat pads onto discs.
23.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).SWITCH - STOP LIGHT
Service repair no - 70.35.42
Remove
1.Disconnect 2 Lucars from stop light switch.
2.Remove mastic from around switch.
3.Remove switch from pedal box.
Refit
4.Fit and tighten switch to pedal box.
5.Apply mastic to switch.
6.Connect 2 Lucars to switch.
ProCarManuals.com

86 - ELECTRICAL
CONTENTS
Page
DESCRIPTION AND OPERATION
SECURITY AND CENTRAL DOOR LOCKING 1....................................................
SECURITY AND CENTRAL DOOR LOCKING 2....................................................
ANTI-THEFT ALARM - FROM 02MY 3...................................................................
IMMOBILISATION SYSTEM - FROM 02MY 12......................................................
CENTRAL DOOR LOCKING (CDL) - FROM 02MY 15...........................................
ANTI-THEFT ALARM SYSTEM SELF TEST 17.....................................................
FASCIA CONSOLE 18............................................................................................
HEATED FRONT SCREEN - FROM 02MY 20.......................................................
HEATED FRONT SEATS - FROM 02MY 22..........................................................
ELECTRIC FRONT WINDOWS - FROM 02MY 24.................................................
PASSENGER COMPARTMENT FUSE BOX 26.....................................................
UNDER SEAT FUSE BOX 27.................................................................................
ADJUSTMENT
HEADLAMPS - ALIGN BEAM 1..............................................................................
SOLENOID/MOTOR - FRONT DOOR - ADJUST 1................................................
REPAIR
BELT - AUXILLARY DRIVE 1.................................................................................
HARNESS - INJECTORS 1....................................................................................
STARTER MOTOR 2..............................................................................................
CENTRE HIGH MOUNTED STOP LIGHT (CHMSL) - UP TO 02MY 2...................
ALTERNATOR 3.....................................................................................................
HORN - LH 4...........................................................................................................
HEADLAMP 5.........................................................................................................
LAMP - TAIL 6.........................................................................................................
RADIO6 ..................................................................................................................
SPEAKER - FRONT 7.............................................................................................
SWITCH - TRANSMISSION BRAKE 7...................................................................
LAMP - FRONT FLASHER 8..................................................................................
BATTERY - DISCONNECT - FROM 02MY 8..........................................................
MOTOR & REGULATOR - FRONT DOOR - FROM 02MY 9..................................
SWITCH - FASCIA - FROM 02MY 10.....................................................................
HARNESS - FRONT DOOR - FROM 02MY 10.......................................................
SOLENOID/MOTOR - TAIL DOOR - FROM 02MY 11............................................
SOLENOID/MOTOR - FRONT DOOR - FROM 02MY 12.......................................
SOLENOID/MOTOR - REAR DOOR - FROM 02MY 13.........................................
HARNESS - REAR DOOR - FROM 02MY 14.........................................................
REVERSE AND FOG GUARD LAMP - BULB 15....................................................
ProCarManuals.com

86ELECTRICAL
26
DESCRIPTION AND OPERATION PASSENGER COMPARTMENT FUSE BOX
FROM 02MY
The increase in electrical systems on Defender 02MY vehicles has necessitated an increase in the number of
fuses required.
The passenger compartment fuse box now contains three rows of fuses instead of the previous two rows and
relays to control the CDL system, heated front screen, headlamps, anti-theft alarm ECU and seat heaters and
window lift system.
1.Fuse 8 - Anti-theft alarm ECU/BBUS (10A)
2.Fuse 9 - Front wiper motor and washer pump
(15A)
3.Fuse 10 - Rear wiper relay (10A)
4.Fuse 11 - ABS ECU (10A)
5.Fuse 12 - Engine Control Module (10A)
6.Fuse 13 - Brake pedal switch (10A)
7.Fuse 14 - Reverse lamp switch/Glowplugs (10A)
8.Fuse 15 - Miscellaneous relay control. See
Electrical Library (5A)
9.Fuse 16 - Cigar lighter/Heater blower (20A)
10.Fuse 17 - Radio (5A)
11.Fuse 18 - LH side lamps/trailer pick up (10A)
12.Fuse 19 - RH side lamps/trailer pick up (10A)
13.Fuse 20 - Headlamp levelling/Illumination (10A)
14.Fuse 21 - Direction indicators (10A)
15.Fuse 22 - RH headlamp dip beam (10A)
16.Fuse 23 - LH headlamp dip beam (10A)
17.Fuse 24 - RH headlamp main beam (10A)
18.Fuse 25 - LH headlamp main beam (10A)19.Fuse 26 - Rear fog lamp ECU (10A)
20.Fuse 27 - Alarm relay (10A)
21.Fuse 28 - Air conditioning blower relay (30A)
22.Fuse 29 - Air conditioning compressor
relay/cooling fan relay (20A)
23.Fuse 30 - Interior lamps/radio/alarm
LED/clock/diagnostic socket/tachometer (South
African vehicles only) (5A)
24.Fuse 31 - Hazard warning lamps (15A)
25.Fuse 32 - Heated rear window (20A)
26.Fuse 33 - Seat heat relay (20A)
27.Fuse 34 - RH window lift switch (20A)
28.Fuse 35 - LH window lift switch (20A)
29.Fuse 36 - Heated front screen (30A)
30.Relay - Heated Front Screen
31.Relay - Starter motor
32.Relay - Heated Rear Window
33.Relay - Headlamps
34.Relay - Anti-theft alarm
35.Relay - Seat heat/window lift
ProCarManuals.com