1999 LAND ROVER DEFENDER brake fluid

MAINTENANCE
1
MAINTENANCE UNDERBONNET VIEW - Td5
LHD shown
1.Engine oil dipstick
2.Coolant expansion tank
3.Air cleaner
4.Brake/clutch fluid reservoir filler cap5.Windscreen washer reservior
6.Auxiliary drive belt
7.Engine oil filler cap
8.PAS fluid reservoir
ProCarManuals.com

MAINTENANCE
7
MAINTENANCE BRAKE PADS, CALIPERS AND DISCS
1.With front road wheels removed, check brake
pad thickness and ensure that both pads are
wearing evenly.
2.Check brake discs for signs of cracking,
excessive scoring or oil contamination.
NOTE: Any requirement to replace brake
pads or brake disc should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
3.Check for any signs of brake fluid leakage from
caliper seals, hoses or unions.
4.Using brake cleaner, remove excessive deposits
of brake dust from pads, calipers and disc
shields.ROAD WHEEL SPEED SENSOR HARNESS - Td5
1.Check each sensor harness is correctly and
securely routed.
2.Inspect each harness for chafing or damage.
NOTE: Any requirement to replace a road
wheel speed sensor should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
ProCarManuals.com

MAINTENANCE
11
MAINTENANCE BRAKE FLUID
1.Renew brake fluid.See BRAKES,
Adjustment.AIR FILTER ELEMENT AND DUMP VALVE
1.Replace air cleaner element.See FUEL
SYSTEM, Repair.
2.Remove all dirt from dump valve.
ProCarManuals.com

10MAINTENANCE
24
MAINTENANCE ENDORSE SERVICE RECORD
1.Insert date and mileage of next service.
2.Insert current mileage.
3.Tick one of the boxes on the brake fluid
replacement indicator.
4.Endorse service record with dealer stamp.
5.Sign and date the service record.
6.Sign and date the maintenance check sheet.REPORT ANY UNUSUAL FEATURES
1.Produce a written report detailing additional work
necessary, or items which may require attention
prior to the next service.
ProCarManuals.com

CLUTCH
5
DESCRIPTION AND OPERATION 1.Brake/clutch reservoir
2.Fluid supply pipe
3.Hydraulic feed pipe
4.Damper
5.Master cylinder
6.Piston
7.Clutch pedal
8.Primary driveshaft
9.Engine crankshaft
10.Drive plate
11.Dual mass flywheel
12.Ring gear
13.Leaf spring
14.Cover - pressure plate
15.Diaphragm
16.Release bearing
17.Ball spigot
18.Release bearing sleeve
19.Release lever
20.Slave cylinder
21.Piston
22.Bleed nipple
ProCarManuals.com

33CLUTCH
6
DESCRIPTION AND OPERATION DESCRIPTION
General
The clutch system is a diaphragm type clutch operated by a hydraulic cylinder. The drive plate is of the rigid centre
type with no integral damping springs. The flywheel is of the dual mass type with damping springs integral with the
flywheel. The clutch requires no adjustment to compensate for wear.
Hydraulic Clutch
The hydraulic clutch comprises a master cylinder, slave cylinder and a hydraulic reservoir. The master and slave
cylinders are connected to each other hydraulically by plastic and metal pipes. The plastic section of the pipe
allows ease of pipe routing and also absorbs engine movements and vibrations.
The master cylinder comprises a body with a central bore. Two ports in the body connect the bore to the hydraulic
feed pipe to the slave cylinder and the fluid reservoir. The bore is also connected to a damper which prevents
engine pulses being transferred hydraulically to the clutch pedal. A piston is fitted in the bore and has an external
rod which is attached to the clutch pedal with a pin. Two coil springs on the clutch pedal reduce the effort required
to depress the pedal.
The master cylinder is mounted on the bulkhead and secured with two bolts. The cylinder is connected to the
shared brake/clutch reservoir on the brake servo by a braided connecting hose.
The slave cylinder is located on the left hand side of the gearbox housing and secured with two bolts. A heat
shield is fitted to protect the underside of the slave cylinder from heat generated from the exhaust system. The
slave cylinder comprises a cylinder with a piston and a rod. A port in the cylinder body provides the attachment for
the hydraulic feed pipe from the master cylinder. A second port is fitted witha bleed nipple used for removing air
from the hydraulic system after servicing. The piston rod locates on a clutch release lever located in the gearbox
housing. The rod is positively retained on the release lever with a clip.
Clutch Mechanism
The clutch mechanism comprises a flywheel, drive plate, pressure plate, release lever and a release bearing. The
clutch mechanism is fully enclosed at the rear of the engine by the gearbox housing.
A clutch release bearing sleeve is attached in the gearbox housing with two bolts and located on two dowels. A
spigot with a ball end is formed on the release bearing sleeve and provides a mounting and pivot point for the
clutch release lever. A dished pivot washer is located on the ball of the spigot. When the release lever is located
on the ball, the pivot washer seats against the rear face of the release lever. A spring clip is located on the lever
and the pivot washer and secures the lever on the spigot. A small bolt retains the spring clip in position.
The release lever is forked at its inner end and locates on the clutch release bearing carrier. The outer end of the
release lever has a nylon seat which locates the slave cylinder piston rod. A second nylon seat, positioned
centrally on the release lever, locates on the ball spigot of the release bearing sleeve and allows the release lever
to pivot freely around the ball.
The clutch release bearing locates on the clutch release lever and release bearing sleeve. The bearing is retained
on a carrier which has two flats to prevent the carrier rotating on the release lever. A clip retains the release lever
on the carrier. The bearing and carrier are not serviceable individually.
ProCarManuals.com

CLUTCH
1
ADJUSTMENT HYDRAULIC SYSTEM - BLEED
Service repair no - 33.15.01
Check
CAUTION: Ensure the fluid in the reservoir
is maintained between the minimum and
maximum levels throughout the bleed
procedure using new brake fluid.
CAUTION: Brake fluid will damage paint
finished surfaces. If spilled, immediately
remove fluid and clean area with water.
1.Top up clutch system reservoir.
2.Raise front of vehicle and support on stands.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove dust cap, connect bleed tube to bleed
screw and submerge free end into a clear
container of brake fluid.
4.Loosen bleed screw, then apply steady pressure
to the clutch pedal, depressing it through its full
stroke. Allow the pedal to return unassisted.
5.Repeat the procedure until a flow of clean,
air-free fluid is purged into the container.
6.Hold pedal down and tighten bleed screw to9
Nm (7 lbf.ft).
7.Check and top up reservoir.
CAUTION: Never re-use fluid that has been
bled from the system.
8.Remove stands and lower vehicle.
ProCarManuals.com

CLUTCH
3
REPAIR
5.Disconnect multiplug from clutch pedal sensor.
6.Disconnect muliplug and harness clip from pedal
bracket.
7.Position cloth to collect fluid spillage.
8.Loosen pipe union, release pipe and plug pipe
and master cylinder.
9.Move brake master cylinder assembly aside and
lift out clutch master cylinder assembly.
10.Remove 6 screws, remove pedal box top cover
and discard gasket.
11.Remove nut securing push rod to clutch pedal
trunnion.
12.Remove 2 bolts and remove clutch master
cylinder from pedal bracket.
13.Remove clutch pedal sensor and pipe union
from master cylinder and discard sealing
washers.Refit
14.Clean sensor and pipe union.
15.Fit clutch pedal sensor and pipe to master
cylinder using new sealing washers.
16.Position master cylinder to pedal bracket and
align push rod to pedal trunnion.
17.Fit bolts and nuts and secure master cylinder to
pedal bracket.
18.Fit nut securing push rod to clutch pedal trunnion
but do not tighten nut at this stage.
19.Move brake master cylinder aside and position
clutch master cylinder assembly.
20.Clean clutch pipe union.
21.Align pipe and tighten union.
22.Connect multiplug to clutch pedal sensor.
23.Tighten bolts securing clutch pedal and brake
pedal brackets to body.
24.Fit clutch pedal rubber.
25.Position closing panel and tighten screws to
lower’A’post.
ProCarManuals.com