yellowblue
6-50 Rims and Wheels
Rims and wheels are stamped with a maximum load and
cold inflation rating. Be sure you don't exceed these limits.
Dual Tire Operation
When the vehicle is new, or whenever a wheel, wheel
bolt or wheel nut is replaced, check the wheel nut torque
as indicated:
If your vehicle has stud piloted or hub piloted wheels,
tighten the wheel stud nuts to the specified torque values
at 100 miles (160 km), 500 miles (800 km) and
1,000 miles (1 600 km) and then every 1,000 miles
(1 600 km) thereafter.
For proper torque, see ªWheel Nut Torqueº in the Index.
The outer tire on a dual wheel setup generally wears
faster than the inner tire. Your tires will wear more
evenly and last longer if you rotate the tires periodically.
If you're going to be doing a lot of driving on
high
-crown roads, you can reduce tire wear by adding
5 psi (35 kPa) to the tire pressure in the outer tires. Be
sure to return to the recommended pressures when no
longer driving under those conditions. See ªChanging a
Flat Tireº in the Index for more information.
CAUTION:
If you operate your vehicle with a tire that is
badly underinflated, the tire can overheat. An
overheated tire can lose air suddenly or catch
fire. You or others could be injured. Be sure
all tires (including the spare, if any) are
properly inflated.
ProCarManuals.com
yellowblue
7-20
(16) = Check spring-to-axle U-bolts and shackle bolts
for proper torque. See the service manual for torque
sequence and specifications. When parts are replaced,
the torque must be checked and adjusted more often
during the first 6,000 miles (10 000 km). Check torque
at 500 miles (800 km) and 2,000 miles (3 000 km) after
first use of parts.
(17) = Check complete exhaust system and cab areas
near the exhaust system for broken, damaged, missing or
out
-of-position parts. Also inspect for open seams,
holes, loose connections or other conditions which could
let exhaust fumes seep into the driver compartment.
Needed repairs should be made at once. To help
maintain system integrity, replace exhaust pipes
whenever a new muffler is put on.
(18) = Check all engine drive belts for cracks, fraying,
wear and proper tension. Adjust or replace as needed.
(19) = Check throttle linkage for damaged or missing
parts (including throttle return springs), interference or
binding. Fix any problems at once. Do not lubricate
accelerator and cruise control cables.
(20) = With the engine off and below normal operating
temperature, check to see that the thermostatically
controlled engine cooling fan can be rotated by hand on
viscous
-operated drives. Replace as needed.(21) = Check shields and underhood insulation for
damage or looseness. Adjust or replace as needed.
(22) = Lubricate caliper housing, caliper support spring
and caliper support key.
(23) = Wheel bearing service:
Grease type
-- Clean, inspect and lubricate with the
proper wheel bearing grease at designated intervals
or when hubs are removed. See ªRecommended
Fluids and Lubricantsº in the Index.
Oil
-filled type -- Some wheel bearings are lubricated
by rear axle lubricant. When you have oil
-filled
hubs, use lubricant identical to that used in your rear
axle. Lubricant change intervals are the same for
front and rear axles. However, you must maintain oil
level at the OIL LEVEL mark between change
intervals. See ªRecommended Fluids and
Lubricantsº in the Index.
(24) = Check the air intake system installation to see
that gaskets are seated properly and all hose
connections, fasteners and other components are tight.
For gasoline engines, also check to be sure the air
cleaner housing is properly seated, that the cover fits
tightly and that the wing nut is tight. Tighten
connections and fasteners or replace parts as required.
ProCarManuals.com
