1999 GMC C-SERIES lock

yellowblue
5-17
3. Remove the rubber
cap from the rear of
the chamber.
4. Put the release stud, nut and flat washer into
the chamber.
5. Turn the stud clockwise a quarter of a turn.6. Using a wrench, turn the
stud nut clockwise
several turns to release
the brakes. Follow the
same procedure to
release the other brake.
7. At the repair facility, apply air pressure of at least
70 psi (480 kPa) to the brake chambers, either from
an external air supply or the vehicle's air system.
8. Turn the stud nut counterclockwise several turns.
Remove the stud from the chamber.
9. Put the stud into the side of the chamber, and replace
the rubber cap.
ProCarManuals.com

yellowblue
5-25 How to Add Coolant to the Radiator
1. You can remove the
radiator pressure cap
when the cooling
system, including the
radiator pressure cap and
upper radiator hose, is
no longer hot.
Turn the pressure cap slowly counterclockwise until
it first stops. (Don't press down while turning the
pressure cap.)
If you hear a hiss, wait for that to stop. A hiss means
there is still some pressure left.
2. Then keep turning
the pressure cap, but
now push down as you
turn it. Remove the
pressure cap.
3. Fill the radiator with the
proper DEX
-COOL

coolant mixture, up to
the base of the filler
neck. (See ªEngine
Coolantº in the Index
for more information
about the proper
coolant mixture.)
ProCarManuals.com

yellowblue
5-31
1. You can remove the coolant surge tank pressure cap
when the cooling system, including the coolant surge
tank pressure cap and upper radiator hose, is no
longer hot. Turn the pressure cap slowly
counterclockwise until it first stops. (Don't press
down while turning the pressure cap.)
If you hear a hiss, wait for that to stop. A hiss means
there is still some pressure left.2. Then keep turning the cap, but now push down as
you turn it. Remove the pressure cap.
ProCarManuals.com

yellowblue
5-35

If the wheel looks normal, see if the wheel has side
rings and a lock ring around the wheel rim. If so,
they must be seated properly. You can compare with
another wheel on the vehicle as you check for this.
For dual wheels, you have to look between the tires
to make this check. You may not be able to tell
if the side rings or lock rings are seated properly
by looking. If you can't be sure, stop and get
expert help.
CAUTION:
If you work on a pressurized tire mounted on a
damaged wheel, the assembly can expand with
explosive force without warning. You and others
nearby can be badly injured. Don't work around
a tire that has air under pressure in it when its
lock ring or side ring might not be
properly seated.
CAUTION:
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel nuts
become loose after a time. The wheel could come
off and cause an accident. When you change a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle. In an
emergency, you can use a cloth or a paper towel
to do this; but be sure to use a scraper or wire
brush later, if you need to, to get all the rust or
dirt off.

If the lock ring and side rings seem to be seated
properly (or if the wheel doesn't have these), let the
air out of the tire. You can do this by taking out the
valve core.

If the flat or damaged tire is one of a dual set, let the
air out of both tires of the dual before you take off
the damaged tire and rim assembly.

If you have the correct equipment, put on the spare
wheel and tire assembly.
ProCarManuals.com

yellowblue
6-7
Filling Your Tank
CAUTION:
Fuel vapor is highly flammable. It burns
violently, and that can cause very bad injuries.
Don't smoke if you're near gasoline or diesel fuel,
or if you're refueling your vehicle. Keep sparks,
flames and smoking materials away from
gasoline or diesel fuel.
The fuel cap can be on either or both sides of your
vehicle depending on option content.
To take off the cap, turn it slowly to the left
(counterclockwise).
CAUTION:
Gasoline Engine Vehicles: If you get gasoline on
you and then something ignites it, you could be
badly burned. Gasoline can spray out on you if
you open the fuel filler cap too quickly. This
spray can happen if your tank is nearly full, and
is more likely in hot weather. Open the fuel filler
cap slowly and wait for any ªhissº noise to stop.
Then unscrew the cap all the way.
When you put the cap back on, turn it to the right until
it is tight.
ProCarManuals.com

yellowblue
6-9
Checking Things Under the Hood
To tilt the hood forward, pull out on each of the hood
latches. If the hood is equipped with hood access panels,
make sure the panel latches are locked down before
rotating the hood open.
Then take the hand holds and pull the hood forward.
ProCarManuals.com

yellowblue
6-20
Rear Axle
When to Check and Change Lubricant
Refer to the Maintenance Schedule to determine how
often to check the lubricant and when to change it.
See ªScheduled Maintenance Servicesº in the
Maintenance Schedule.
How to Check Lubricant
If the level is below the bottom of the filler plug hole,
you'll need to add some lubricant. Add enough lubricant
to raise the level to the bottom of the filler plug hole.
What to Use
Refer to the Maintenance Schedule to determine what
kind of lubricant to use. See ªRecommended Fluids and
Lubricantsº in the Maintenance Schedule.
Rear Axle Shift Motor (Option)
When to Check and Change Fluid
If you have an optional air-shift two-speed, controlled
traction, or locking differential type rear axle, a good
time to check the fluid level in the axle shift motor is
when the rear axle lubricant is checked. Use refrigerant
oil (shift motor only).
How to Check Fluid
Remove the plug on the front plate of the axle shift
motor, add enough fluid to raise the level to the bottom
of the filler plug hole, then replace the plug.
What to Use
Refer to your Maintenance Schedule to determine what
kind of lubricant to use.
ProCarManuals.com

yellowblue
6-46 Automatic Ether Injection System (Option)
If your diesel engine vehicle
has this feature, the ether
cylinder is on the upper
right rear side of the engine
compartment.
To change an empty ether cylinder, follow these steps.
1. Loosen the 5/16 inch screw head on the
cylinder
-to-bracket clamp.
2. Spread the clamp apart.3. Clean any dirt from the neck of the cylinder and the
top of the valve before you take out the cylinder.
4. Check the inside of the valve for any foreign matter.
Clean the valve as necessary.
5. Cover the valve to protect it from dirt and take out
the cylinder.
6. Install a new gasket whenever you take out the
cylinder. Use only one gasket and spread a light film
of clean oil on it before installation.
7. Put in the new cylinder. Turn it clockwise until it just
starts to contact the gasket.
8. Tighten the cylinder another half turn (180 degrees).
Don't over
-tighten.
9. Retighten the cylinder clamp.
ProCarManuals.com