1999 DODGE RAM Fuel pressure

pump to drain the fuel tank, go to next step.
2) Disconnect fuel line from fuel rail. See FUEL LINE AT FUEL
RAIL. Connect Fuel Hose (6541, 6539, 6631 or 6923) for proper engine
application at fuel line fitting on fuel rail. Place remaining end of
fuel hose in an approved gasoline container.
3) Connect scan tool to Data Link Connector (DLC). DLC is a
16-pin connector attached to bottom of driver's side of the instrument
panel, just straight above the accelerator pedal. Using scan tool
manufacturer's instructions, activate the fuel pump and pump fuel from
fuel tank. Once fuel tank is empty, remove scan tool. Reinstall fuel
line on fuel rail using proper procedure. Go to step 5).
4) Release fuel pressure from fuel system. See FUEL SYSTEM
PRESSURE RELEASE. Ensure negative battery cable is disconnected.
Remove fuel tank cap to release any residual fuel tank pressure.
5) Raise and support vehicle. Disconnect the small vent hose
from fill and vent hose fitting assembly at driver's side frame rail.
Fill and vent hose fitting assembly is permanently attached on fuel
tank. See Fig. 30.
6) If fuel tank was previously drained, go to next step. If
fuel tank was not previously drained, siphon fuel from fuel tank into
an approved gasoline container by installing siphon hose in small vent
hose fitting on fill and vent hose fitting assembly. Go to next step.
7) Disconnect large fill hose from fill and vent hose fitting
assembly at driver's side frame rail. Fill and vent hose fitting
assembly is permanently attached on fuel tank. See Fig. 30.
8) Support fuel tank with transmission jack. Remove fuel tank
strap retaining nuts from L-shaped bolts securing fuel tank straps on
frame rail. Remove fuel tank straps.
CAUTION: Fill and vent hose fitting assembly must be released from
plastic shield before lowering fuel tank. Use care when
lowering fuel tank as not to damage fill and vent hose
fitting assembly or the fuel tank.
9) Fill and vent hose fitting assembly is permanently
attached on fuel tank and is protected from the frame by a plastic
shield. See Fig. 30. Push retaining tabs inward to release fill and
vent hose fitting assembly from the plastic shield before lowering the
fuel tank. See Fig. 38.
Fig. 38: Releasing Retaining Tabs From Plastic Shield (Ram Van &
Ram Wagon)
Courtesy of Chrysler Corp.
10) Slightly lower fuel tank while guiding fill and vent hose

fitting assembly out of the plastic shield. Use care not to damage
fill and vent fitting assembly. Disconnect fuel line from fuel
filter/fuel pressure regulator on fuel pump module using proper
procedure for fuel line disconnect fitting. See FUEL LINE DISCONNECT
FITTINGS. Fuel pump module is located on top of fuel tank. See Fig. 30
.
11) Disconnect electrical connector at fuel pump module.
Disconnect vapor hoses from rollover valves on top of fuel tank. See
Fig. 30 . Lower fuel tank from vehicle. Use care not to damage fill and
vent hose fitting assembly.
Installation
1) To install, reverse removal procedure. Install fuel lines
on fuel filter/fuel pressure regulator on fuel pump module using
proper procedure. See FUEL LINE DISCONNECT FITTINGS.
2) Ensure retaining tabs on fill and vent hose fitting
assembly fully engage the plastic shield. Tighten fuel tank strap
retaining nuts to specification. See TORQUE SPECIFICATIONS. Start
engine and check for fuel leaks.
FUEL RAIL & INJECTORS
Removal (Dakota 2.5L)
1) Release fuel pressure from fuel system. See FUEL SYSTEM
PRESSURE RELEASE. Ensure negative battery cable is disconnected.
2) Disconnect air inlet duct at throttle body for access to
fuel rail. Disconnect vent line from fuel damper at end of fuel rail
(if equipped).
3) Note electrical connector location on injectors for
installation reference. Disconnect electrical connectors at injectors.
Disconnect fuel line from fuel rail. See FUEL LINE AT FUEL RAIL.
Disconnect control cables at throttle body. Remove control cable
mounting bracket from intake manifold for access to fuel rail.
4) Remove fuel rail bolts. Ensure area around injectors and
intake manifold is clean. Using rocking motion, remove fuel rail with
injectors from intake manifold.
5) If removing injector from fuel rail, remove retaining clip
from fuel rail and injector. Retaining clip is located at top of
injector and fuel rail. Remove injector with "O" ring from fuel rail.
Installation
1) If installing injector on fuel rail, install NEW "O" ring
on injector. Coat "O" ring on injector with engine oil. Install
injector on fuel rail. Install retaining clip on injector and fuel
rail.
2) To install remaining components, reverse removal procedure
using NEW "O" ring at bottom of each injector. Coat "O" ring on
injector with engine oil before installing injectors and fuel rail.
3) Tighten fuel rail bolts to specification. See TORQUE
SPECIFICATIONS. Install fuel line on fuel rail using proper procedure.
See FUEL LINE AT FUEL RAIL. Start engine and check for leaks.
Removal (Dakota 3.9L, 5.2L & 5.9L, Durango, Ram Pickup 3.9L,
5.2L & 5.9L, Ram Van & Ram Wagon)
1) Release fuel pressure from fuel system. See FUEL SYSTEM
PRESSURE RELEASE. Ensure negative battery cable is disconnected.
2) On Ram Van and Ram Wagon, remove engine cover. On all
models, remove air cleaner. Remove throttle body from intake manifold.
See THROTTLE BODY. On A/C equipped models, remove A/C compressor-to-
intake manifold support brace at rear of A/C compressor.
3) On all models, note electrical connector location on
injectors for installation reference. Disconnect electrical connectors
at injectors. Disconnect any necessary wiring electrical connectors

for access to fuel rails and injectors.
CAUTION: Both fuel rails are serviced as an assembly. DO NOT attempt
to separate fuel rail from connecting fuel hose at rear of
each fuel rail. Connecting fuel hose does not use any form of
clamps on the hose. DO NOT use any clamps on connecting fuel
hose. When removing fuel rails with injectors, use care not
to bend connecting fuel hose.
4) Disconnect fuel line from fuel rail. See FUEL LINE AT FUEL
RAIL. Remove fuel rail bolts. Ensure area around injectors and intake
manifold is clean.
5) Using rocking motion, pull driver's side fuel rail with
injectors upward from intake manifold until injectors just clear
intake manifold. Repeat procedure on passenger's side fuel rail.
Remove fuel rails with injectors from intake manifold.
6) If removing injector from fuel rail, remove retaining clip
from fuel rail and injector. Retaining clip is located at top of
injector and fuel rail. Remove injector with "O" ring from fuel rail.
Installation
1) If installing injector on fuel rail, install NEW "O" ring
on injector. Coat "O" ring on injector with engine oil. Install
injector on fuel rail. Install retaining clip on injector and fuel
rail.
2) To install remaining components, reverse removal procedure
using NEW "O" ring at bottom of each injector. Coat "O" ring on
injector with engine oil before installing injectors and fuel rails.
3) Push passenger's side fuel rail and then driver's side
fuel rail downward until shoulder on each injector contacts the intake
manifold. Ensure all injectors are fully seated.
4) Tighten fuel rail bolts and throttle body bolts to
specification. See TORQUE SPECIFICATIONS. Install fuel line on fuel
rail using proper procedure. See FUEL LINE AT FUEL RAIL under FUEL
SYSTEM. Start engine and check for leaks.
Removal (Ram Pickup 8.0L)
1) Release fuel pressure from fuel system. See FUEL SYSTEM
PRESSURE RELEASE. Ensure negative battery cable is disconnected.
2) Remove throttle body from upper intake manifold. See
THROTTLE BODY. Remove ignition coils with mounting bracket for access
to fuel rails.
3) Upper intake manifold must be removed for servicing of
fuel rails and injectors. Remove generator-to-upper intake manifold
brace and A/C compressor-to-upper intake manifold brace. Remove
generator and A/C compressor if necessary for removal of upper intake
manifold.
4) Disconnect necessary vacuum lines and hoses for removal of
upper intake manifold. Remove bolts, upper intake manifold and gasket
from lower intake manifold.
5) Note electrical connector location on injectors for
installation reference. Disconnect electrical connectors at injectors.
Disconnect fuel line from fuel rail. See FUEL LINE AT FUEL RAIL.
6) Remove fuel rail bolts. Ensure area around injectors and
lower intake manifold is clean. Using rocking motion, pull driver's
side fuel rail with injectors upward from intake manifold until
injectors just clear intake manifold. Repeat procedure on passenger's
side fuel rail. Remove fuel rails with injectors from lower intake
manifold.
7) If removing injector from fuel rail, remove retaining clip
from fuel rail and injector. Retaining clip is located at top of
injector and fuel rail. Remove injector with "O" ring from fuel rail.

\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Crankshaft Position Sensor Bolt
2.5L ..................................................... 14 (19)\
3.9L, 5.2L & 5.9L ............................................ (1)
8.0L ......................................................... ( 1)
Downstream Oxygen Sensor ................................... 22 (30)\
Distributor Hold-Down Bolt ................................. 17 (23)\
EVAP Canister-To-Mounting Bracket Nut
Dakota & Durango ......................................... 17 (23)\
Ram Pickup ................................................... ( 2)
Ram Van & Ram Wagon .......................................... ( 3)
Fuel Pump Module Lock Nut
Dakota ................................................... 40 (54)\
Ram Pickup ............................................... 32 (43)\
Ram Van & Ram Wagon ...................................... 40 (54)\
Fuel Rail Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
8.0L ..................................................... 11 (15)\
Fuel Tank Strap Nut
Dakota & Durango ......................................... 40 (54)\
Ram Pickup ............................................... 30 (41)\
Ram Van & Ram Wagon .......................................... ( 5)
IAT Sensor ................................................. 20 (27)\
Park/Neutral Switch ........................................ 25 (34)\
Power Steering Pressure Switch (2.5L) ...................... 16 (22\
)
Spark Plug ................................................. 30 (41)\
Throttle Body Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
Throttle Body Nut (8.0L) ................................... 16 (22\
)
Upper Intake Manifold Bolt (8.0L) ...................... ( 6) 16 (22)
Upstream Oxygen Sensor ..................................... 22 (30)\
Wheel Lug Nut (Dakota & Durango) ......................... 100 (136\
)
INCH Lbs. (N.m)
Air Cleaner Housing-To-Throttle
Body Nut (Dakota & Durango) ............................. 96 (10.8\
)
Camshaft Position Sensor Bolt (8.0L) ...................... 50 (5.6\
)
Engine Coolant Temperature Sensor ........................ 96 (10.8)\
EVAP Canister Mounting Bracket-To
Body Nut (Ram Van & Ram Wagon) .......................... 95 (10.7\
)
EVAP Leak Detection Pump Filter
Bolt (Ram Pickup, Ram Van & Ram Wagon) ................... 65 (7.3\
)
EVAP Leak Detection Pump Bolt ............................. 11 (1.2)\
EVAP Purge Solenoid Nut (Dakota & Durango) ................ 75 (8.5\
)
IAC Motor Bolt ............................................ 60 (6.8)\
Ignition Coil Bolt/Nut
Dakota, Durango, Ram Van & Ram Wagon ......................... ( 7)
Ram Pickup
3.9L, 5.2L & 5.9L ........................................... ( 7)
8.0L .................................................. 90 (10.2)\
MAP Sensor Bolt
Dakota & Durango ........................................ 25 (2.8)\
Ram Pickup
3.9L, 5.2L & 5.9L ...................................... 25 (2.8)\
8.0L ................................................... 20 (2.3)\
Ram Van & Ram Wagon ..................................... 25 (2.8)\
PCM Bolt .................................................. 35 (4.0)\
TP Sensor Bolt ............................................ 60 (6.8)\

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\

\
\
\

\
\
\


Manual  NV4500  4 Qts. (3.8L) 

Transmission   

Fluid   

\

\
\
\

\
\
\


Rear Axle  DANA 70 Model 267 (2WD)  7 Pts. (3.3L) 

Lubricant 
\
\
\

\
\


 DANA 70 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 DANA 80 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 DANA 80 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 267 (2WD)  7 Pts. (3.3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 248  7.6 Pts. (3.6L) 

Lubricant   

\

\
\
\

\
\
\


Transfer Case NV241 HD  6.5 Pts. (3.1L) 

Fluid   

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank  Capacity  35 Gal. (132L) 

\
\
\
\
\
\
\




(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear

  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\

\
\
\

\
\
\


Transfer Case NV231 HD  2.5 Pts. (1.2L) 

Fluid   

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L) 


\
\
\

\
\


 All Others  35 Gal. (132L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation

 Lubricant   

\

\
\
\

\
\
\


Transfer Case NV241 HD  6.5 Pts. (3.1L) 

Fluid   

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank  Capacity  35 Gal. (132L) 

\
\
\
\
\
\
\




(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, drain water from fuel filter.
* Once a month, check Filter Minder.
* Once a month, inspect and clean wiper blades as required.

 \
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\

\
\
\

\
\
\


Transfer Case NV241  5 Pts. (2.7L) 

Fluid 
\
\
\

\
\


 NV241 HD  6.5 Pts. (3.5L) 


\
\
\

\
\


 NV241 HD W/PTO  9 Pts. (4.9L) 

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L) 


\
\
\

\
\


 All Others  35 Gal. (132L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, Inspect and clean wiper blades as required.
* Twice a year, lubricate the external lock cylinders.