1999 DODGE RAM oil

(1) - Require replacement of units where dents restrict shock
or strut piston rod movement. If dents don't restrict
movement, no service is suggested or required. Especially
critical on mono-tube shocks.
( 2) - This condition can lead to damage of the piston rod,
which, in turn, causes premature piston rod seal wear.
( 3) - Only required if replacing cartridge.
( 4) - CAUTION: If the strut cartridge has been replaced previously,
the oil on the strut housing may be filler oil. The
technician must identify the source of the oil.
( 5) - If noise is isolated to shock or strut, suggest
replacement.
( 6) - Although shocks or struts may have contributed to tire
cupping, an inspection is needed of the entire suspension
system. If the shock or strut is found to be contributing
to the tire cupping, require replacement.









\









\









\









\









\









\









\


SPINDLES
SPINDLE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Race seat area
undersized ............. B ............ Require replacement.
Scored .................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.









\









\









\









\









\









\









\


SPRINGS - COIL, LEAF AND TORSION BAR
When springs are replaced, it is suggested, but not required,
that both springs on an axle be replaced to maintain equal height from
side to side and to provide a balanced ride and proper handling.
When variable rate springs are installed in place of
conventional coil springs, they must be installed in axle sets to
ensure proper handling, uniform ride, and proper chassis height.
Erroneous height measurements may result from: improper tire
inflation, non-standard tire or wheel size, and heavy load in vehicle
or trunk.
SPRING (COIL, LEAF AND TORSION BAR) INSPECTION

\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
bent .................. B .... Require repair or replacement
of bent part.
Attaching hardware
broken ................ A .... Require replacement of broken
part.
Attaching hardware
corroded, affecting
structural integrity .. A .. Require replacement of corroded
part.
Attaching hardware
incorrect ............. A ........... Require replacement of
incorrect part.
Attaching hardware
loose ................. A .... Require repair or replacement
of loose part.
Attaching hardware
missing ............... C ... Require replacement of missing
part.
Attaching hardware
threads damaged ....... A .... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ..... A ...... Require replacement of part
with stripped threads.
Broken (all springs
except secondary
leave(s) on multi-leaf
springs) .............. A ............. Require replacement.
Coil clash ............. .. .. (1) Require ride height check.
Coil spring insulator
deteriorated .......... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
missing ............... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
split ................. 2 ........... Suggest replacement of
insulator.
Coil spring plastic
coating deteriorated -
rust present .......... A ...... ( 2) Refer to manufacturer's
service requirements.
Composite spring
damaged ............... .. .......... ( 3) Further inspection
required.
Cracked (all springs
except composite leaf and
secondary leave(s) on
multi-leaf springs) ... A ............. Require replacement.
Installed incorrectly .. B .................. Require repair.
Leaf spring insulators
missing ............... 2 ........... Suggest replacement of
insulators.
Secondary leaf on multi-
leaf spring broken .... 1 .... Suggest repair or replacement
Secondary leaf on multi-
leaf spring cracked ... 1 .... Suggest repair or replacement
Torsion bar

replace steering damper.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace steering damper.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace steering
damper.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace steering
damper.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace steering damper.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace steering damper.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
steering damper.
Binding ................. A ............ Require replacement.
Damper body dented ...... A .......... (1) Further inspection
required.
Damper body punctured ... A ............ Require replacement.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
missing ................ 2 ......... ( 2) Suggest replacement
of boot.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Leaking oil, enough for
fluid to be running
down the body .......... A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noise ................... 2 .......... ( 3) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Seized .................. A ............ Require replacement.
( 1) - Require replacement of units where dents restrict damper


SU SPEN SIO N - F R O NT - 2 W D C O IL S PR IN G
1999 D odge P ic ku p R 1500
1998-99 SUSPENSION
CHRY - Front - 2WD Coil Spring
Ram Pickup
DESCRIPTION
All models are equipped with independent front suspension,
consisting of upper and lower control arms, steering knuckles, coil
springs and shock absorbers. See Fig. 1. Upper control arms are
mounted to frame side rails. Lower control arms are mounted to
crossmember. Steering knuckles are mounted between upper and lower
control arms by conventional ball joints. Coil springs are mounted
between seat in frame and lower control arm.
Fig. 1: Exploded View Of Front Suspension
Courtesy of Chrysler Corp.
ADJUSTMENTS & INSPECTION

WHEEL ALIGNMENT
NOTE: See appropriate SPECIFICATIONS & PROCEDURES article in WHEEL
ALIGNMENT.
WHEEL BEARING ADJUSTMENT
1) Tighten wheel bearing adjusting nut to 30-40 ft. lbs. (41-\
54 N.m) while rotating wheel. Stop rotation, and back off adjusting
nut to release all preload. Retighten nut finger tight.
2) Ensure bearing end play is .001-.003" (.025-.076 mm).
Install nut lock and cotter pin. Coat grease cap inside lightly with
grease, and install cap.
BALL JOINT CHECKING
Ball joints are preloaded. Replace lower ball joint if
vertical movement exceeds .03" (.8 mm). Replace upper ball joint if
movement exceeds .03" (.8 mm).
REMOVAL & INSTALLATION
COIL SPRING
Removal
1) Raise vehicle, and position safety stands under frame.
Remove wheels. Remove brake caliper retainer and brake caliper (if
necessary). Support caliper aside. Disconnect tie rod from steering
knuckle.
2) Disconnect stabilizer bar link from lower control arm. See
Fig. 1 . Support lower suspension arm outboard end with jack. Place
jack under arm in front of shock mount. Remove cotter pin and nut from
lower ball joint stud. Using Ball Joint Breaker (C-4150A), separate
ball joint from steering knuckle.
3) Remove lower shock bolt from suspension arm. Lower jack
and suspension arm until spring tension is relieved. Remove spring and
rubber isolator.
Installation
1) Install rubber isolator on top of spring. Position spring
between upper spring seat and lower suspension arm. Raise suspension
arm with jack, and position shock into suspension arm mount.
2) Install shock bolt and tighten to specification. See
TORQUE SPECIFICATIONS table. Install steering knuckle on lower ball
joint stud. Install lower ball joint stud nut and tighten. See TORQUE
SPECIFICATIONS table. Replace cotter pin, and remove jack. Install
stabilizer bar link on lower suspension arm. Install grommet, retainer
and nut.
3) Install tie rod on steering knuckle, and tighten nut to 65
ft. lbs. (88 N.m). Install brake caliper assembly and rotor. Install
tire and wheel assembly. Remove support, and lower vehicle.
STEERING KNUCKLE
Removal & Installation
1) Raise and support vehicle. Remove wheel and tire assembly.
Remove brake caliper. Remove wheel hub and bearing assembly from
spindle.
2) Remove cotter pin and nut from tie-rod end, and disconnect
tie rod. Remove cotter pins and nut from upper and lower ball joint

stud. Separate upper ball joint stud from knuckle with Ball Joint
Breaker (MB-990635).
3) Separate lower ball stud with Ball Joint Breaker (C-
4150A). Remove knuckle. To install, reverse removal procedure. Tighten
all nuts and bolts to specification. See TORQUE SPECIFICATIONS table.
LOWER CONTROL ARM & BALL JOINT
Removal
1) Raise and support vehicle. Remove wheel. Support lower
control arm.
CAUTION: DO NOT remove shock until lower control arm is supported.
Shock holds lower control arm and spring in position.
2) Remove shock absorber and coil spring. See COIL SPRING.
Remove bolts mounting lower control arm to crossmember. Remove lower
control arm.
Bushing Replacement
If bushings are worn, use a sleeve and press to remove and
replace bushings.
Installation
To install, reverse removal procedure. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table.
STABILIZER BAR
Removal & Installation
Raise and support vehicle. Remove link rod retaining nut at
each end of stabilizer bar. Remove outer retainers and rubber bushings
from link rods. Remove stabilizer bar clamps from frame rails. Remove
stabilizer bar from vehicle. To install, reverse removal procedure.
Ensure stabilizer bar is centered in chassis. Tighten all nuts and
bolts to specifications.
UPPER CONTROL ARM & BALL JOINT
Removal
1) Raise vehicle, and position safety stands under frame.
Remove wheel. Support upper control arm.
2) Disconnect upper ball joint. Refer to step 2) under LOWER
CONTROL ARM & BALL JOINT. Remove pivot bolts and control arm.
Bushing Replacement
If bushings are worn, use a sleeve and press to remove and
replace bushings.
Installation
To install, reverse removal procedure. Ensure ball joint is
fully seated against control arm. With vehicle at normal operating
height, tighten all retaining nuts and bolts to specifications. See
TORQUE SPECIFICATIONS table.
WHEEL BEARINGS
Removal
1) Raise and support vehicle. Remove wheel. Remove brake
caliper, and support it aside. Remove inboard brake pad (if
necessary). Remove grease cap, cotter pin, nut, washer and outer wheel
bearing.

CAUTION: To avoid damage to threads, bearing and seal, DO NOT allow
inner bearing and seal to contact spindle threads during
removal.
2) Carefully slide rotor from steering knuckle. Remove oil
seal and inner bearing.
Installation
Clean and inspect bearings. Pack or replace bearings as
required. Install inner bearing and oil seal. Carefully install rotor
and outer bearing, washer, and nut. Adjust wheel bearings. See WHEEL
BEARING ADJUSTMENT under ADJUSTMENTS & INSPECTION. To install
remaining components, reverse removal procedure.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Ball Joint Nuts
Lower
Light Duty ............................................. 95 (129)\
Heavy Duty ............................................ 110 (149)\
Upper .................................................... 60 (81)\
Lower Control Arm-To-Crossmember Bolt .................... 145 (196)\
Lower Shock Absorber Mounting Bolt
1998 Models ............................................ 100 (135)\
1999 Models ........................................... 105 (142))\
Stabilizer Bar Bolts/Nuts
Frame End ................................................ 40 (54)\
Link End ................................................. 25 (34)\
Tie Rod End Nut ............................................ 40 (54)\
Upper Ball Joint-To-Control Arm .......................... 125 (169)\
Upper Control Arm Eccentric Cam Bolt ....................... 70 (95)\
Upper Control Arm Pivot Bar To Frame ..................... 150 (203)\
Upper Shock Absorber Mounting Bolt
1998 Models .............................................. 35 (47)\
1999 Models .............................................. 40 (54)\
Wheel Lug Nuts
Tapered (Coned)
1/2"-20 ............................................... 105 (142)\
5/8"-18 ............................................... 200 (271)\
Flat (Flanged) (5/8"-18) ............................... 325 (4\
40)









\









\









\









\









\









\









\


SU SPEN SIO N - F R O NT - L IN K/C O IL S PR IN G

1999 D odge P ic ku p R 1500
1998-99 SUSPENSION
CHRY - Front - Link/Coil Spring
Ram Pickup
DESCRIPTION
Link/coil front suspension uses upper and lower suspension
arms attached to frame and drive axle (4WD) or tube axle (2WD). Shoc\
k
absorbers are mounted inside the coil springs, and attached at top to
a bracket with grommets. These brackets are bolted onto the frame with
3 studs on a ring. The shock is mounted at bottom of axle below the
spring seat. See Fig. 1.
A track bar is used, and is attached to a frame rail bracket
with a ball stud. The track bar is isolated with a bushing at the axle
bracket. Other components of the link/coil spring suspension system
are a stabilizer bar, links, upper and lower suspension arms, bushings
and ball joints.
Fig. 1: Exploded View Of Front Suspension Assembly
Courtesy of Chrysler Corp.
ADJUSTMENTS & INSPECTION
WHEEL ALIGNMENT
NOTE: See appropriate SPECIFICATIONS & PROCEDURES article in WHEEL
ALIGNMENT.