1999 DODGE RAM torque

TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Axle Adjustment Nut .............................. 120-140 (163-190)\
Axle Shaft Flange Or Support Plate Mounting Nuts
Dakota .................................................. 47 (64)\
Ram Pickup ........................................ 35-50 (48-68)\
Ram Van ................................................ 85 (115)\
Bearing/Hub Assembly Mounting Bolts ...................... 125 (170)\
Brake Booster Mounting Nuts
Dakota & Ram Pickup ...................................... 21 (29)\
Ram Van .................................................. 13 (18)\
Brake Hose Front Bolt (Dakota) ............................. 21 (29\
)
Brake Hose Front Fitting (Dakota) .......................... 12 (16\
)
Brake Hose Rear Fitting (Dakota) ........................... 14 (19\
)
Brakeline Fittings Combination Valve
Dakota ................................................... 14 (19)\
Ram Pickup ......................................... 14-17 (19-23)\
Brakeline Fittings Master Cylinder
Dakota ................................................... 14 (19)\
Ram Pickup ......................................... 14-17 (19-23)\
Brakeline Fittings Wheel Cylinder
Dakota ................................................... 12 (16)\
Ram Pickup ............................................... 10 (14)\
Brake Pedal Shaft Nut (Ram Van) ............................ 40 (54\
)
Caliper Adapter Bolts (Ram Van)
1/2 Ton ................................................ 130 (176)\
3/4 & 1 Ton ............................................ 210 (285)\
Caliper Mounting Bolts
Dakota (Guide Pins) ...................................... 22 (30\
)
Ram Pickup ............................................... 38 (52)\
Ram Van .................................................. 24 (33)\
Combination Valve Mounting Bolt (Ram Pickup) ............... 17 (23\
)
Diesel Hydraulic Booster Hoses (Ram Pickup) ................ 23 (31\
)
Diesel Hydraulic Booster Lines (Ram Pickup) ................ 21 (29\
)
Diesel Hydraulic Booster Mounting Bolts (Ram Pickup) ....... 21 (29\
)
Drive Flange Lock Nuts (4WD) ............................... 65 (88\
)
Master Cylinder Nuts
Dakota
1998 .................................................... 21 (29)\
1999 .................................................... 13 (18)\
Ram Pickup ............................................... 21 (29)\
Ram Van .................................................. 17 (23)\
Park Brake Pedal Assembly Mounting Bolts/Nuts
Ram Pickup ............................................... 21 (29)\
Ram Van .................................................. 40 (54)\
Pivot Pin .................................................. 30 (41)\
Power Booster Lock Nuts
Dakota & Ram Pickup ...................................... 21 (29)\
Ram Van .................................................. 13 (18)\
Proportioning Valve Brake Hose (Ram Pickup) ................ 23 (31\
)
Proportioning Valve Brakelines (Ram Pickup) .......... 14-17 (19-23\
)
Proportioning Valve Mounting Nuts (Ram Pickup) ............. 25 (34\
)
Wheel Bearing Outer Lock Nut (4WD) ......................... 65 (88\
)
Wheel Cylinder Mounting Bolts
1/4" Bolts (Dakota) ...................................... 11 (15\
)
5/16" Bolts (Dakota) ..................................... 16 (22\
)
Ram Pickup & Ram Van ..................................... 15 (20)\

REMOVAL & INSTALLATION
TRANSFER CASE
CAUTION: When removing transfer case, DO NOT allow drive shafts to
hang free, as damage to "U" joints may result.
Removal (NV231HD, NV241HD & NV241LD - Ram Pickup)
1) Raise and support vehicle. Remove skid plate (if
equipped). Drain lubricant from transfer case if transfer case is
being repaired. Mark drive shafts and "U" joints for reassembly
reference. Disconnect speed sensor wires. Disconnect vent harness and
vent hose from transfer case switch.
2) Disconnect shift rod from grommet in transfer case shift
lever, or from floor arm, whichever provides easy access. Using slip
joint pliers, press rod out of lever grommet. See Fig. 8. Support
transmission with jackstand. Remove rear crossmember. Remove front and
rear drive shafts. Remove transfer case-to-transmission housing nuts.
Using transmission jack, support transfer case. Move transfer case
rearward until free of transmission. Remove transfer case from under
vehicle.
Removal (NV231 & NV242 - Dakota)
1) Shift transfer case into neutral. Raise vehicle. If
transfer case will be repaired, drain lubricant. Mark driveshafts and
"U" joints for reassembly reference. Support transmission with
jackstand. Remove rear crossmember and skid plate, if equipped.
2) Disconnect front and rear driveshafts at transfer case.
Disconnect transfer case linkage rod from shift lever. Disconnect
transfer case vent hose and electrical connectors. Support transfer
case with transmission jack. Remove nuts attaching transfer case to
transmission. Remove transfer case.
Installation (All Models)
To install, reverse removal procedure. If necessary fill
transfer case with MOPAR ATF Plus or Dexron-II. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table. Adjust shift
linkage, if necessary. See SHIFT LINKAGE ADJUSTMENT under ADJUSTMENTS.
Fig. 8: Removing Transfer Case Shift Mechanism (NV4500 & NV4500HD)
Courtesy of Chrysler Corp.
TRANSMISSION (DAKOTA)

Removal (AX15 & NV1500)
1) Shift gear selector into 1st or 3rd gear. Raise and
support vehicle. Disconnect necessary exhaust system components.
Remove "Y" pipe and position remaining pipes for working clearance.
Support transmission adjustable jackstand. Disconnect rear cushion and
mounting bracket from transmission or transfer case.
2) Remove rear crossmember. If transmission will be
disassembled for repair, drain transmission fluid. Disconnect
transmission shift linkage, speedometer cable, transfer case vacuum
lines and clutch hydraulic lines. Lower transmission/transfer case
assembly no more than 3" (76 mm). Reaching around transmission case,
unseat and lift shift lever dust boot. Press shift lever retainer
downward, turn retainer counterclockwise, and lift lever and retainer
out of shift tower.
3) Mark front and rear drive shaft and "U" joint for
reassembly reference. Disconnect and remove both drive shafts. Remove
crankshaft position sensor (AX15). Disconnect transmission/transfer
case assembly vent hoses. Remove slave cylinder from clutch housing.
Remove wire harness from clips on transmission case and transfer case.
4) Support transmission/transfer case assembly with
transmission jack. Secure assembly to jack with safety chains.
Reposition adjustable jackstand under engine. Remove clutch housing
brace rod. Remove clutch housing nuts and bolts. Remove
transmission/transfer case assembly.
Installation
To install, reverse removal procedure. Apply high-temperature
grease to release fork, lever, pivot ball stud and pilot bushing
located in end of crankshaft. Fill transmission with appropriate
fluid, if necessary. Tighten all nuts and bolts to specification. See
TORQUE SPECIFICATIONS table.
Removal (NV 3500)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Open console lid and remove bolts attaching console to floor
pan. Lift cup holder bin and remove bolt attaching console to floor
pan. Lift rear of console and pull console rearward to separate from
shift bezel. Remove console from vehicle. Remove screws attaching
shift boot to floor pan and slide boot upward on lever extension.
2) Remove shift lever extension. Raise and support vehicle.
On 4WD models, remove skid plate, if equipped. Mark drive shaft and
axle yoke for alignment reference. Remove drive shaft. Remove exhaust
"Y" pipe. On 4WD models, disconnect and lower remaining exhaust pipes
for clearance as necessary. Disconnect speed sensor harness connector
and back-up light harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine attaching bolts. Slide

transmission and jack rearward until input shaft clears clutch disc.
Lower transmission jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke. Apply sealer to threads of drain plug
before installing in case.
2) Align reference marks made on drive shaft(s) and "U"
joints during removal. After installing clutch assembly and housing,
tighten housing bolts nearest alignment dowels first. During final
transmission installation, install shims between clutch housing and
transmission at appropriate bolt location. Tighten all nuts and bolts
to specification. See TORQUE SPECIFICATIONS table.
TRANSMISSION (RAM PICKUP)
Removal (NV3500 & NV5600)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Remove shift tower and lever assembly. Raise and support
vehicle.
2) On 4WD models, remove skid plate, if equipped. Remove
crankshaft position sensor. Mark drive shaft and axle yoke for
alignment reference. Remove drive shaft. Remove exhaust "Y" pipe. On
4WD models, disconnect and lower remaining exhaust pipes for
clearance, as necessary. Disconnect speed sensor harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover. On
some models, it may be necessary to remove front axle struts and oil
filter for access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table.
Removal (NV4500 & NV4500HD)

1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Scribe mark position of extension on shank of shift lever.
2) Raise and support vehicle. On 4WD models, remove skid
plate, if equipped. Mark drive shaft and axle yoke for alignment
reference. Remove drive shaft. Remove exhaust "Y" pipe. On 4WD models,
disconnect and lower remaining exhaust pipes for clearance as
necessary. Disconnect speed sensor harness connector and back-up light
harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
See Fig. 9 . On 4WD models, disconnect transfer case shift linkage at
transfer case range lever and remove shift lever from transmission.
Remove bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and move it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder, and move aside. Remove
starter. Remove transmission splash shield. Remove transmission
harness wires from clips on transmission shift cover. On some models,
it may be necessary to remove front axle struts and oil filter for
access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and propeller shift slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first.
3) During final transmission installation, install shims
between clutch housing and transmission at appropriate bolt location.
See CLUTCH HOUSING BORE RUNOUT and CLUTCH HOUSING FACE RUNOUT under
CLUTCH HOUSING (RAM PICKUP) under TESTING. Press extension to scribe
mark made during removal. A 0.12-0.20" (3-5 mm) space should exist
between shift lever isolator, top edge of stub shaft and tool lower
jaw. Tighten all nuts and bolts to specification. See TORQUE
SPECIFICATIONS table.
Fig. 9: Identifying Transmission Drain Bolt (NV4500 & NV4500HD)
Courtesy of Chrysler Corp.
CLUTCH ASSEMBLY

CAUTION: Clutch disc may contain asbestos fibers which can cause
serious health risk. DO NOT sand clutch components. DO NOT
clean components using compressed air. To clean components,
use a water-dampened cloth.
Removal
With transmission and clutch housing removed, mark pressure
plate and flywheel for reassembly reference. Install clutch aligner in
clutch disc to prevent disc from falling. Loosen pressure plate bolts
evenly and in rotation to avoid warping pressure plate. Remove
pressure plate and disc from flywheel. See Fig. 10.
Inspection
1) Check for oil leakage through engine rear main bearing oil
seal and transaxle input shaft seal. Check flywheel and pressure plate
for burned areas, discoloration, cracks, grooves or ridges. Replace as
necessary.
2) Use medium sandpaper (80-180 grade) to clean flywheel
surface, then wipe with mineral spirits. DO NOT flat-machine flywheel
surface. Check facing surfaces for grease or oil contamination. Check
clutch disc for wear. Clutch disc face-to-rivet head distance should
be at least .008" (.20 mm). Check splines of disc hub and transaxle
input shaft.
3) Using straightedge, check pressure plate. Friction area
should be flat to slightly concave, with the inner diameter about 0-.
0039" (0-0.1 mm) less than outer diameter. Using surface plate, check
clutch cover for flatness. Sections around bolt holes should contact
surface plate within .015" (.38 mm). Ensure cover-to-flywheel dowel
fit is snug. Replace clutch assembly as necessary.
NOTE: Before installing clutch disc, ensure flywheel mating
surface, pilot bearing/bushing and clutch release bearing are
in satisfactory condition. Repair and/or replace components
as necessary.
Installation
To install, reverse removal procedure using clutch aligner.
Ensure reference marks are aligned. Tighten pressure plate retaining
bolts evenly a few threads at a time to prevent warpage. See TORQUE
SPECIFICATIONS table.
Fig. 10: Exploded View Of Clutch Assembly (Typical)
Courtesy of Chrysler Corp.
PILOT BEARING, CLUTCH RELEASE BEARING & FORK

TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Clutch Master Cylinder Nuts ................................ 40 (54)\
Clutch Slave Cylinder Nuts ................................. 17 (23)\
Crossmember-To-Frame Bolts
AX15 & NV3500 (Dakota) ..................................... 30 (41\
)
NV3500 (Ram Pickup) ........................................ 50 (68\
)
Crossmember-To-Transmission Insulator Nuts
2WD (NV3500 - Ram Pickup) ................................ 50 (68\
)
4WD (NV3500 - Ram Pickup) .......................... 40-45 (54-61\
)
Flywheel Bolts
Dakota 2.5L ................................................ 70 (95)\
Dakota V6 & V8 ............................................. 55 (75)\
Pressure Plate Bolts
5/16" .................................................... 17 (23)\
3/8" ..................................................... 30 (41)\
Transfer Case To Transmission Nuts
AX15 ................................................. 26 (35 N.m)\
NV3500, NV4500, NV4500HD & NV5600
5/16" ............................................. 22-30 (30-41)\
3/8" .............................................. 30-35 (41-47)\
Transmission-To-Clutch Housing Bolts
AX15 ..................................................... 27 (37)\
NV3500 (Ram Pickup) & NV5600 ....................... 40-45 (54-61\
)
NV1500, NV3500 (Dakota), NV4500 & NV 4500HD ............. 80 (108\
)
"U" Joint Clamp Bolts ...................................... 14 (19)\
INCH Lbs. (N.m)
Shift Tower Bolts (NV3500) ............................ 62-89 (7-10\
)









\









\









\









\









\









\









\

FLUID TYPE
Use SAE 80W-90 or 90W hypoid gear lubricant with MIL-L-2105-C
and API GL-5 ratings.
TROUBLE SHOOTING
NOTE: See appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
REMOVAL & INSTALLATION
AXLE SHAFT & HUB BEARING
Removal
1) Raise and support vehicle. Remove wheel. Remove brake
caliper with hose attached, and secure aside. DO NOT allow brake
caliper to hang by brake hose. Remove brake rotor. Remove ABS wheel
speed sensor (if equipped). Remove grease cap from center of front
hub. Remove cotter pin from end of axle shaft. Remove axle nut and
washer.
2) Remove hub/bearing assembly-to-knuckle bolts. Remove
hub/bearing assembly from steering knuckle and axle shaft. Remove
brake dust shield. To remove right (passenger-side) axle shaft,
carefully pull axle shaft from axle housing.
NOTE: Left axle shaft will disengage from collar located on
intermediate axle shaft.
3) To remove left (driver's side) axle shaft, disconnect
electrical connector and vacuum hoses at vacuum shift motor. Remove
bolts, vacuum shift motor and gasket. Carefully pull axle shaft from
axle housing and collar on intermediate axle shaft.
Installation
1) Install NEW oil seal on axle shaft with seal lip facing
toward splines on differential end of axle shaft. Coat seal lip with
wheel bearing grease.
2) Install right axle shaft into axle housing. Ensure axle
shaft engages with side gears in differential.
3) To install left axle shaft, ensure collar is engaged with
splines on intermediate axle shaft. Install left axle shaft into axle
housing. Ensure axle shaft engages with splines on collar. Install
vacuum shift motor, ensuring fork on vacuum shift motor engages groove
on collar. Install and tighten bolts to specification. See TORQUE
SPECIFICATIONS table.
4) To complete installation, reverse removal procedure. Apply
silicone rubber sealant to edge of grease cap before installing.
Tighten bolts/nuts to specification. See TORQUE SPECIFICATIONS table.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer selector levers case are in Neutral. Reference mark drive
shaft and pinion flange for reassembly reference.
2) Remove bolts and "U" joint straps at pinion flange. Remove
center carrier bearing bolts (if equipped). Remove drive shaft.
CAUTION: The "U" joint components are not serviceable. Replace
complete assembly. DO NOT reuse.