1999 DODGE RAM oil pressure

Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, record freeze frame data. Use scan tool to read DTCs. If
DTC SPECIFIC GOOD TRIPS counter is not displayed or displayed count is
not "0", go to step 11). If DTC SPECIFIC GOOD TRIPS counter is
displayed and displayed count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and ground circuit at Black PCM harness connector C1. If resistance
is less than 550 ohms, go to step 8). If resistance is 550 ohms or
more, go to next step.
3) If resistance is 550-2300 ohms, go to next step. If
resistance is greater than 2300 ohms, go to DTC P0713: TRANS TEMP
SENSOR VOLTAGE TOO HIGH.
4) Measure resistance of transmission temperature signal
circuit between ground and White PCM harness connector C2. If
resistance is 5 ohms or less, go to step 8). If resistance is greater
than 5 ohms, go to next step.
5) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is less than 1.5 volts, replace PCM. If
voltage is 1.5 volts or greater, go to step 7). On all other bodies,
go to next step.
6) Conditions required to set DTC P0712 are not present at
this time. DTC P0712 sets when transmission temperature sensor voltage
at PCM is less than 1.55 volts for 2.2 seconds. Possible causes are:
shorted transmission temperature sensor wiring, faulty connections,
faulty transmission temperature sensor or faulty PCM. Go to next step.
7) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and sensor ground circuit at Black PCM harness connector C1. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground circuit. If resistance is 5 ohms or
greater, go to next step.
9) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground. If resistance is 5 ohms or greater, go to
next step.
10) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
sensor ground circuit at Black PCM harness connector C1. If resistance
is less than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or greater, go to next step.
11) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair or replace transmission
solenoid and harness assembly. If resistance is 5 ohms or greater,
replace transmission pressure/temperature sensor.
DTC P0713: TRANS TEMP SENSOR VOLTAGE TOO HIGH
Circuit Description
Circuit is monitored continuously while key is on, and engine

running. Code sets if transmission temperature sensor voltage is
greater than 3.76 volts for 2.2 seconds.
Possible Causes
* Transmission solenoid and wiring harness assembly
defective.
* Transmission temperature sensor wiring harness defective.
* Transmission temperature sensor ground circuit open.
* Transmission temperature signal circuit short to voltage.
* Transmission temperature sensor signal circuit open.
* PCM defective.
* Transmission pressure/temperature sensor defective.
Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, use scan tool to read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
11). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure voltage between ground and
transmission temperature signal circuit at White PCM harness connector
C2. If voltage is greater than one volt, go to next step. If voltage
is one volt or less, go to step 5).
3) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure voltage between ground and
transmission temperature signal circuit at transmission solenoid
harness connector. If voltage is greater than one volt, repair
transmission temperature signal circuit for short to ground. If
voltage is one volt or less, go to next step.
4) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure voltage between ground and
transmission temperature signal circuit at transmission
pressure/temperature sensor harness connector. If voltage is greater
than one volt, repair or replace transmission solenoid and harness
assembly. If voltage is one volt or less, replace transmission
pressure/temperature sensor.
5) Turn ignition off. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
ground circuit at Black PCM harness connector C1. If resistance is
less than 550 ohms, go to DTC P0712: TRANS TEMP SENSOR VOLTAGE TOO
LOW. If resistance is 550 ohms or more, go to next step.
6) If resistance is 550-2300 ohms, go to step 10). If
resistance is greater than 2300 ohms, go to next step.
7) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance of sensor ground
circuit between Black PCM harness connector C1 and transmission
solenoid harness. If resistance is 5 ohms or greater, repair open in
transmission temperature signal circuit. If resistance is less than 5
ohms, go to next step.
8) Measure resistance of transmission temperature signal
circuit between White PCM harness connector C2 and transmission
solenoid harness connector. If resistance is less than 5 ohms, go to
next step. If resistance is 5 ohms or greater, repair open
transmission temperature signal circuit.
9) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance of sensor ground circuit

2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS









\









\









\









\









\









\









\







DTC DTC Message
P0122 (1) ................. THROTTLE POSITION SENSOR VOLTAGE TOO LOW
P0123 ( 1) ................ THROTTLE POSITION SENSOR VOLTAGE TOO HIGH
P1696 ( 1) .......................... PCM FAILURE EEPROM WRITE DENIED
P0743 ........ TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS
( 2) ........................................................ MISFIRE
P0320 ( 1) ......................... NO CRANK REFERENCE SIGNAL AT PCM
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
( 2) - Perform appropriate misfire DTC test. See appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Start engine. Using scan tool, perform TCC SYSTEM TEST. If
vehicle does not stall, go to step 9). If vehicle stalls, go to next
step.
5) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If vehicle stalls, go to next step. If vehicle
does not stall, go to step 7).
6) Turn ignition off. Replace TCC solenoid. Using scan tool,
perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
vehicle stalls, problem in internal. Check for blocked passage. If
vehicle does not stall, testing is complete.
7) Turn ignition off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
8) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
9) Turn ignition off. Connect a pressure gauge to
transmission cooler OUT port. Start engine. Using scan tool, perform
TCC SYSTEM TEST. If pressure increases when TCC is actuated, go to
next step. If pressure does not increase, repair leaks or blockage in
hydraulic circuit, or repair valve body as necessary.
10) Turn engine off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, there are no other potential causes remaining.
TCC is assumed to be defective. Replace torque converter.
DTC P0743: TORQUE CONV CLUTCH SOLENOID/TRANS RELAY CKT
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on Torque Converter Clutch (TCC) at the Powertrain\
Control Module (PCM) does not match desired voltage.
Possible Causes

CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
5) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair
as necessary. If connector and terminals are okay, turn ignition on.
Using scan tool, actuate transmission control relay. Measure voltage
between ground and transmission relay output circuit at transmission
solenoid harness connector. If voltage does not switch from zero to
greater than 10 volts, go to step 18). If voltage switches from zero
to greater than 10 volts, go to next step.
6) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, turn ignition on. Measure voltage
between ground and governor pressure solenoid control circuit at
transmission solenoid harness connector. If voltage is greater than 10
volts, go to step 8). If voltage is 10 volts or less, go to next step.
7) Repair governor pressure solenoid control circuit for
short to ground. Reconnect all disconnected harness connectors. Using
scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st
gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
8) Turn ignition off. Reconnect transmission solenoid harness
connector. Measure resistance between ground and governor pressure
solenoid control circuit at White PCM harness connector C2. If
resistance is 5 ohms or less, repair short to ground in governor
pressure solenoid control circuit. If resistance is greater than 5
ohms, go to next step.
9) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, measure resistance between
transmission control relay output circuit at transmission control
relay connector and governor pressure solenoid control circuit at
White PCM harness connector C2. If resistance is 2.5-5.0 ohms, replace
PCM. If resistance is not 2.5-5.0 ohms, go to next step.
10) Measure resistance between transmission control relay
output circuit at transmission control relay connector and governor
pressure solenoid control circuit at White PCM harness connector C2.
If resistance is greater than 5 ohms, go to next step. If resistance
is 5 ohms or less, go to step 13).
11) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance of governor
pressure solenoid control circuit between White PCM harness connector
C2 and transmission solenoid harness connector. If resistance is
greater than 5 ohms, repair open governor pressure solenoid control.
If resistance is 5 ohms or less, go to next step.
12) Drain transmission fluid and remove oil pan. Disconnect
governor pressure solenoid harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance across governor pressure solenoid
terminals. If resistance is 5 ohms or less, repair or replace
transmission solenoid and harness assembly. If resistance is greater
than 5 ohms, replace governor pressure solenoid.
13) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between governor
pressure solenoid control circuit and all other circuits at
transmission solenoid harness connector. If resistance is less than 2.
5 ohms between any 2 circuits, go to next step. If resistance is not
less than 2.5 ohms between any 2 circuits, go to step 15).
14) Repair governor pressure solenoid control circuits that
were shorted together. Reconnect all disconnected harness connectors.
Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select

1st gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
15) Drain transmission fluid and remove oil pan. Disconnect
governor pressure solenoid harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance across governor pressure solenoid
terminals. If resistance is 2.5 ohms or less, go to next step. If
resistance is greater than 2.5 ohms, go to step 17).
16) Replace governor pressure solenoid. Replace oil pan and
fill with fluid. Reconnect all disconnected harness connectors. Using
scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st
gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
17) Repair or replace transmission solenoid and harness
assembly. Reconnect all disconnected harness connectors. Using scan
tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st gear and
read governor pressure voltage. If voltage is one volt or greater,
replace PCM. If voltage is less than one volt, test is complete.
18) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
19) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If
resistance is 5 ohms or less, go to next step.
20) Measure resistance between ground and transmission
control relay output circuit at transmission solenoid harness
connector. If resistance is less than 5 ohms, repair open in
transmission control relay output circuit. If resistance is 5 ohms or
greater, replace transmission control relay.
Diagnostic Procedure (AB, BR & WJ Bodies)
NOTE: On WJ body, if all solenoid codes, P0743, P0748 and P0753 are
set, go to test DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL
CIRCUIT before proceeding.
1) Using scan tool, read DTCs. On BR and WJ bodies, go to
next step. On AB body, if DTC SPECIFIC GOOD TRIPS counter is not
displayed or displayed count is not "0", go to step 20). If DTC
SPECIFIC GOOD TRIPS counter is displayed and displayed count is "0",
indicating DTC still exists, go to next step.
2) If DTC P1765 is also set, go to DTC DTC P1765: TRANS 12-
VOLT SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is not set, go to next
step.
3) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 1st gear and read governor pressure voltage. If voltage
is one volt or greater, go to step 20). If voltage is less than one
volt, go to next step.
4) Turn ignition off. Disconnect transmission solenoid
harness connector. Turn ignition on. Using scan tool, actuate
transmission control relay. Measure voltage between ground and
transmission relay output circuit at transmission solenoid harness
connector. If voltage does not switch from zero to greater than 10
volts, go to step 17). If voltage switches from zero to greater than
10 volts, go to next step.
5) Turn ignition off. Disconnect PCM harness connectors.

Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, turn ignition on. Measure voltage
between ground and governor pressure solenoid control circuit at
transmission solenoid harness connector. If voltage is greater than 10
volts, go to next step. If voltage is 10 volts or less, go to step 7).
6) Repair governor pressure solenoid control circuit for
short to voltage. Reconnect all disconnected harness connectors. Using
scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st
gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
7) Turn ignition off. Reconnect transmission solenoid harness
connector. Measure resistance between ground and governor pressure
solenoid control circuit at White PCM harness connector C2. If
resistance is 5 ohms or less, repair short to ground in governor
pressure solenoid control circuit. If resistance is greater than 5
ohms, go to next step.
8) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, measure resistance between
transmission control relay output circuit at transmission control
relay connector and governor pressure solenoid control circuit at
White PCM harness connector C2. If resistance is 2.5-5.0 ohms, replace
PCM. If resistance is not 2.5-5.0 ohms, go to next step.
9) Measure resistance between transmission control relay
output circuit at transmission control relay connector and governor
pressure solenoid control circuit at White PCM harness connector C2.
If resistance is greater than 5 ohms, go to next step. If resistance
is 5 ohms or less, go to step 12).
10) Drain transmission fluid and remove oil pan. Disconnect
governor pressure solenoid harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance across governor pressure solenoid
terminals. If resistance is 5 ohms or less, repair or replace
transmission solenoid and harness assembly. If resistance is greater
than 5 ohms, go to next step.
11) Measure resistance of governor pressure solenoid control
circuit between White PCM harness connector C2 and transmission
solenoid harness connector. If resistance is greater than 5 ohms,
repair open governor pressure solenoid control circuit. If resistance
is 5 ohms or less, replace governor pressure solenoid.
12) Measure resistance between governor pressure solenoid
control circuit and all other circuits at transmission solenoid
harness connector. If resistance is less than 2.5 ohms between any 2
circuits, go to next step. If resistance is not less than 2.5 ohms
between any 2 circuits, go to step 14).
13) Repair governor pressure solenoid control circuits that
were shorted together. Reconnect all disconnected harness connectors.
Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select
1st gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
14) Drain transmission fluid and remove oil pan. Disconnect
governor pressure solenoid harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance across governor pressure solenoid
terminals. If resistance is 2.5 ohms or less, go to next step. If
resistance is greater than 2.5 ohms, go to step 16).
15) Replace governor pressure solenoid. Replace oil pan and
fill with fluid. Reconnect all disconnected harness connectors. Using
scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st
gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is

replace PCM and see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
DTC P0783: 3-4 SHIFT SOL, NO RPM DROP @ 3-4 SHIFT
Circuit Description
Circuit is monitored continuously while key is on and engine
running. Code sets if expected RPM drop does not occur within 4
seconds of requested gear change by PCM. Test must fail 3 times to set
code.
Possible Causes
* Transmission mechanically defective.
* TPS codes set.
* Transmission 3-4 solenoid wiring harness defective.
* Transmission fluid burnt or oil pan has excessive debris.
Diagnostic Procedures
1) Using scan tool, read DTCs. On all bodies except AB and WJ
bodies, go to next step. On AB and WJ bodies, if DTC SPECIFIC GOOD
TRIPS counter is not displayed or displayed count is not "0", go to
step 6). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", indicating DTC still exists, go to next step.
2) If any DTCs listed are present, perform appropriate
test(s). See 3-4 SHIFT SOLENOID TESTS table. If no DTCs are present,
go to next step.
3-4 SHIFT SOLENOID TESTS









\









\









\









\









\









\









\







DTC Message Test
NO CAM SIGNAL AT PCM ..................................... ( 1) P0340
P/N SWITCH STUCK IN PARK OR IN GEAR .......................... P1899
Any Throttle Position Sensor (TPS) DTC ......................... ( 1)
TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS ........ P0743
TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT ..................... P1765
TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS ................ P0753
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Connect a 0-300 psi (0-21 kg/cm
) pressure gauge to
transmission Overdrive (O/D) clutch pressure test port. Connect a
second 0-300 psi (0-21 kg/cm
) pressure gauge to transmission governor
pressure test port. See appropriate AUTOMATIC TRANSMISSION OVERHAUL
article. Ensure engine and transmission are at normal operating
temperature. With an assistant, test drive vehicle. Using scan tool,
select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear while
monitoring pressure gauge. Governor pressure should rise to greater
than 20 psi (1.4 kg/cm
) and O/D pressure should rise to greater than
40 psi (2.8 kg/cm). If pressures are as specified, go to next step.
If pressures are not as specified, go to step 8).
5) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, go to next step.
6) Using scan tool, erase DTCs. Start engine. Road test
vehicle at 0-55 MPH with a constant 20 percent throttle. Repeat road
test 4 times. Note if DTC P0783 resets. If DTC P0783 resets, repair
wiring harness as necessary. If DTC P0783 does not reset, go to next

step.
7) Turn engine off. Drain transmission fluid and remove oil
pan. Inspect oil pan for burnt oil and debris. Repair transmission as
necessary. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, no problem is found at this time, see INACTIVE
DTC CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Leave gauges connected. Replace 3-4 shift solenoid.
Replace transmission pan and fill with fluid. Start engine and allow
engine and transmission to reach normal operating temperature. Using
scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear
while monitoring pressure gauges. Governor pressure should rise to
greater than 20 psi (1.4 kg/cm
) and O/D pressure should rise to
greater than 40 psi (2.8 kg/cm). If pressures are as specified, no
problem is found at this time. Testing is complete. If pressures are
not as specified, see appropriate AUTOMATIC TRANSMISSION OVERHAUL
article, paying attention to seals and clutches related to O/D clutch.
DTC P1740: TCC OR O/D SOLENOID PERFORMANCE (BR BODY - DIESEL)
Circuit Description
Torque Converter Clutch (TCC) and overdrive clutch are tested\
when Powertrain Control Module (PCM) requests TCC engagement in 3rd
gear and overdrive. Code will set if expected RPM drop is not achieved
while attempting to engage TCC and/or overdrive. Code indicates
malfunctioning torque converter or overdrive clutch.
Possible Causes
* Fluid level or quality problem.
* Transmission wiring and connector defective.
* Transmission mechanically defective.
* Low fuel level.
* Trans temperature below 32
.
* Transfer case is in low range.
* Engine RPM trouble codes set.
* Misfire trouble code set (DTCs P0300-P0306).
* Output shaft speed trouble code set.
* PTO is engaged.
* TPS codes set (DTCs P0121-P0123).
* Torque converter defective.
Diagnostic Procedures
1) Using scan tool, read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
16). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) If any DTCs listed are present, perform appropriate
test(s). See TCC OR O/D SOLENOID TESTS table. If no DTCs are present,
go to next step.
TCC OR O/D SOLENOID TESTS









\









\









\









\









\









\









\







DTC Message Test
CAMSHAFT POSITION SENSOR SIGNAL .......................... ( 1) P0341
P/N SWITCH STUCK IN PARK OR IN GEAR .......................... P1899
Any Throttle Position Sensor (TPS) DTC ......................... ( 1)
Any Misfire DTC ................................................ ( 1)
Any Engine RPM DTC ............................................. ( 1)
Any Output Shaft Speed Sensor DTC .............................. ( 1)
TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT ..................... P1765
TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS ........ P0743
TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS ................ P0753