1999 DODGE RAM transmission

damage clockspring and/or require clockspring to be
readjusted.
NOTE: Clockspring is self-centering and will automatically lock in
the centered position when steering wheel is removed.
Adjustment is only required if centering position is
disturbed.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Clockspring is located behind steering wheel. See Fig. 1.
Ensure front wheels are in straight-ahead position. Lock steering
wheel. Remove air bag module. See AIR BAG MODULE.
3) Remove steering wheel nut. Using appropriate steering
wheel puller, remove steering wheel. When steering wheel is removed,
self-centering clockspring will automatically lock in place. Remove
upper and lower steering column shrouds to gain access to clockspring
wiring.
4) Remove knee bolster (if equipped). Disconnect Yellow 2-wa\
y
clockspring harness connector between clockspring and instrument panel
wiring harness, at base of steering column. See Fig. 13. Remove
clockspring by releasing 2 tabs on side of clockspring. Clockspring
cannot be repaired and must be replaced if faulty.
Installation
1) Snap clockspring onto steering column. If clockspring
centering adjustment is disturbed, adjust clockspring before
installing steering wheel. See CLOCKSPRING CENTERING under
ADJUSTMENTS. Connect clockspring wiring connectors. Install steering
column covers. Install knee bolster (if removed).
2) Position steering wheel on steering column. Ensure flats
on steering wheel hub fit formations on inside of clockspring. Pull
clockspring, cruise control switch (if equipped) and horn wires
through lower large holes and upper small holes in steering wheel.
3) Install steering wheel retaining nut and tighten to 45 ft.
lbs. (61 N.m). Connect horn and cruise control wires (if equipped).
Connect clockspring wire to air bag module. To ensure complete
connector connection, latching arms must be visible on top of
connector housing. DO NOT connect negative battery cable at this time.
Go to SYSTEM OPERATION CHECK .
PASSENGER AIR BAG DISARM (PAD) SWITCH
Removal & Installation
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) If vehicle is equipped with automatic transmission, turn
ignition switch to UNLOCK position, set parking brake and place
transmission selector lever in LOW position. Tilt steering column to
lowest position (if equipped). Using trim stick, gently pry around
perimeter of cluster bezel and remove bezel.
3) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
4) Reach through glove box opening to access and disconnect 2
passenger-side air bag disarm switch harness connectors. Connectors
are attached to bracket located on inboard glove box opening
reinforcement. See Fig. 4. Remove 3 screws retaining passenger-side
air bag disarm switch bezel to instrument panel.

NOTE: All active codes must be resolved before diagnosing store
codes.
1) Raise and support vehicle. Start engine and let idle with
transmission in PARK position. Wiggle wiring harness and connectors of
air bag system and rotate steering wheel from stop to stop.
2) Visually inspect related wire harness connectors. Look for
broken, bent, pushed out, spread, corroded or contaminated terminals.
Also, look for chafed, pierced, pinched or partially broken wires.
3) Check for trouble codes as you work through system. If
stored trouble code becomes active, perform appropriate diagnostic
test. If stored code is reproducible, repair or replace wiring
harness, harness connector or terminals or replace component as
necessary.
CLUSTER MESSAGE MISMATCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) If AIR BAG warning light is on, go to next step. If AIR
BAG warning light is not on, go to step 5).
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG and MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB does not display MIC LAMP
STATUS ON, replace instrument cluster. If DRB displays MIC LAMP STATUS
ON, go to next step.
3) If DRB displays ACM LAMP REQUEST: ON, go to next step. If
DRB does not display ACM LAMP REQUEST: ON, replace instrument cluster.
4) If there are no potential causes for this DTC remaining,
ACM is assumed to be defective. Replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
NOTE: If AIR BAG warning light is defective, instrument cluster
will flash seat belt light for 30 seconds starting 10 seconds
after bulb check stops.
5) Using DRB, read air bag control module active codes
(messages). If CLUSTER MISMATCH is only active message, go to next
step. If other messages are present, go to appropriate diagnostic test
to continue diagnosis.
6) If seat belt warning light flashes for 30 seconds after
bulb check is complete, replace instrument cluster. If seat belt
warning light does not flashes for 30 seconds after bulb check is
complete, go to next step.
7) Using DRB, select PASSIVE RESTRAINTS, AIRBAG and MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB displays ACM LAMP REQUEST:
OFF, go to next step. If DRB does not display ACM LAMP REQUEST: OFF,
replace instrument cluster.
8) If DRB displays MIC LAMP REQUEST: OFF, go to next step. If
DRB does not display MIC LAMP REQUEST: OFF, replace instrument
cluster.
9) If there are no potential causes for this DTC remaining,
ACM is assumed to be defective. Replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
DRIVER SQUIB CIRCUIT OPEN
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect

it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Disconnect battery and wait 2 minutes before proceeding.
Disconnect driver-side air bag module squib connector. Connect a
jumper wire between driver-side air bag (squib) 2-pin connector
terminal No. 1 (Black/Light Blue wire) and terminal No. 2 (Dark
Green/Light Blue wire). Turn ignition on (engine off). Reconnect
battery. Using DRB, read active codes. If DRB displays DRIVER SQUIB
CIRCUIT SHORTED, replace driver-side air bag module. If not, go to
next step.
2) Disconnect clockspring 2-pin connector. Connect a jumper
wire between clockspring 2-pin connector terminals No. 1 (Black/Light
Blue wire) and No. 2 (Dark Green/Light Blue wire). Using DRB, read
active codes. If DRB displays DRIVER SQUIB CIRCUIT SHORTED, replace
clockspring. If not, go to next step.
3) Disconnect battery and wait 2 minutes before proceeding.
Remove jumper wires. Disconnect ACM connector. ACM is located under
instrument panel, on transmission tunnel. Using an ohmmeter, check
resistance between ACM connector terminal No. 6 (Dark Green/Light Blue
wire) and clockspring 2-pin connector terminal No. 2 (Dark Green/Light\
Blue wire). If resistance is less than 5 ohms, go to next step. If
resistance is more than 5 ohms, repair open or high resistance in Dark
Green/Light Blue wire.
4) Check resistance between ACM connector terminal No. 5
(Black/Light Blue wire) and clockspring 2-pin connector terminal No. 1\
(Black/Light Blue wire). If resistance is less than 5 ohms, go to next\
step. If resistance is more than 5 ohms, repair open or high
resistance in Black/Light Blue wire.
5) If there are no potential causes for this DTC remaining,
ACM is assumed to be defective. Replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
DRIVER SQUIB CIRCUIT SHORTED
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Disconnect battery and wait 2 minutes before proceeding.
Ensure driver-side air bag module connector is completely connected
before disconnecting it. If driver-side air bag module connector is
not completely connected, reconnect it. If driver-side air bag
connector is completely connected, go to next step.
2) Disconnect driver-side air bag module. Turn ignition on
(engine off). Reconnect battery. Using DRB, read active codes. If DRB
displays DRIVER SQUIB CIRCUIT OPEN, replace driver-side air bag
module. If not, go to next step.
3) Disconnect clockspring 2-pin connector. Using DRB, read
active codes. If DRB displays DRIVER SQUIB CIRCUIT OPEN, replace
clockspring. If not, go to next step.
4) Turn ignition off, disconnect battery and wait 2 minutes
before proceeding. Disconnect passenger-side air bag module connector.
Using an ohmmeter, check resistance between clockspring 2-pin
connector terminal No. 1 (Black/Light Blue wire) and passenger-side
air bag 2-pin connector terminal "A" (Black/Yellow wire). If
resistance is less than 5 ohms, repair short between Black/Light Blue
wire and Black/Yellow wire. If resistance is more than 5 ohms, go to


AU TO T R AN S D IA G NO SIS - 4 2R E, 4 4R E, 4 6R E & 4 7R E

1999 D odge P ic ku p R 1500
1999 AUTOMATIC TRANSMISSIONS
Chrysler 42RE, 44RE, 46RE & 47RE Electronic Controls
MODEL IDENTIFICATION
Vehicle body codes are used throughout self-diagnostic tests.
See BODY CODE DESIGNATION table for model identification.
BODY CODE DESIGNATION









\









\









\









\









\









\









\







Model Body Code
Dodge
Dakota ........................................................ AN
Durango ....................................................... DN
Pickup ........................................................ BR
Ram Van/Wagon ................................................. AB
Jeep Grand Cherokee ............................................. WJ









\









\









\









\









\









\









\







APPLICATION
TRANSMISSION APPLICATIONS








\









\









\









\









\









\









\







Application Transmission Model
Cab & Chassis
5.9L (Gasoline) ............................................. 46RE\
5.9L (Diesel) & 8.0L ........................................ 47RE\
Dakota & Durango
3.9L ........................................................ 42RE
5.2L ........................................................ 44RE
5.9L ........................................................ 46RE
Grand Cherokee
4.0L ........................................................ 42RE
Ram Pickup
3.9L ........................................................ 42RE
5.2L (RWD) .................................................. 42RE\
5.2L (4WD) .................................................. 46RE\
5.9L (Gasoline) ............................................. 46RE\
5.9L (Diesel) & 8.0L ........................................ 47RE\
Ram Van
5.2L (B3500) ................................................ 46RE\
5.9L ........................................................ 46RE
Ram Wagon (5.2L & 5.9L) ....................................... 46RE\









\









\









\









\









\









\









\







INTRODUCTION
The first step in diagnosing any driveability problem is
verifying the customer's complaint with a test drive under the
conditions the problem reportedly occurred. Before entering self-
diagnostics, perform a careful and complete visual inspection. Most
transmission control problems result from mechanical breakdowns or
poor electrical connections.
DESCRIPTION

Governor pressure is monitored electronically and is used to
control transmission shifting. Electronic control system consists of
Powertrain Control Module (PCM), governor pressure solenoid, governor
pressure sensor, transmission fluid temperature sensor, OD (Overdrive)\
OFF switch, Throttle Position (TP) sensor and output shaft speed
sensor.
NOTE: Governor pressure sensor may also be referred to as governor
pressure transducer. Transmission fluid temperature sensor
may also be referred to as transmission fluid temperature
thermistor. Output shaft speed sensor may also be referred to
as transmission shaft speed sensor or shaft speed sensor.
Transmission shifting is controlled by throttle pressure and
governor pressure. Governor pressure is generated by electronic
components through control of line pressure. Transmission will not
upshift into 4th gear under the following conditions:
* 3rd gear upshift is not complete.
* OD OFF switch is in OFF position.
* Throttle is at 3/4 to WOT position.
* Vehicle speed is too low for 3-4 upshift.
* Transmission fluid temperature is less than 50
F (10C) or
greater than 250F (121C).
* Battery temperature is less than 5F (-15C).
OPERATION
POWERTRAIN CONTROL MODULE (PCM)
The PCM controls Torque Converter Clutch (TCC) operation,
overdrive clutch operation and the governor pressure solenoid. The PCM
determines shift points and TCC operation based on input signals
received from transmission fluid temperature sensor, output shaft
speed sensor, Crankshaft Position (CKP) sensor, Vehicle Speed Sensor
(VSS), Throttle Position (TP) sensor and battery temperature sensor.\
There are 4 governor pressure curves programmed into the PCM.
Governor pressure curves allow the PCM to adjust governor pressure for
varying conditions. One governor pressure curve is used for operation
when transmission fluid temperature is at or less than 30
F (1C). The
second governor pressure curve is used for operation when transmission
fluid temperature is at or greater than 30
F (1C) during normal city
operation or highway driving. The third governor pressure curve is
used for operation during wide open throttle (WOT). The fourth
governor pressure curve is used for operation when transfer case is in
low range.
The PCM controls TCC operation by operating the lock-up
solenoid located on the valve body. Lock-up solenoid may be referred
to as TCC solenoid. If OD switch is in the ON position, the TCC will
lock-up once transmission is in 4th gear with vehicle speed greater
than 45 MPH. If OD switch is in the OFF position, the TCC will lock-up
once transmission is in 3rd gear with vehicle speed greater than 35
MPH at light throttle application. When OD switch is in the OFF
position, the OD light on instrument panel will be illuminated.
The PCM prevents TCC operation and overdrive operation when
transmission fluid temperature is less than 50
F (10C). If
transmission fluid temperature exceeds 260F (126C), the PCM will
cause a 4-3 downshift and engage the TCC. The OD light will be
illuminated when the downshift occurs. Transmission will not upshift
until transmission fluid temperature decreases to approximately 230
F
(110F).

The PCM contains a self-diagnostic system used for
determining an electronic component failure. The PCM self-diagnostic
system will store a Diagnostic Trouble Code (DTC) in PCM memory if
certain electronic problems are present.
DTCs can be retrieved using appropriate scan tool. See SELF-
DIAGNOSTIC SYSTEM. After repairing an electronic system problem,
stored DTC must be cleared from PCM memory. For PCM location, see PCM
LOCATION table.
AB Body
On firewall, near wiper motor.
AN & DN Bodies
Right front fender, near air cleaner.
BR Body
Right front fender, near firewall.
WJ Body
On firewall, near speed control servo.
GOVERNOR PRESSURE SENSOR
NOTE: Governor pressure sensor may also be referred to as governor
pressure transducer.
Governor pressure sensor delivers an output signal to the PCM
indicating the output pressure of governor pressure solenoid. The PCM
uses this signal to control governor pressure. Governor pressure
solenoid is located on valve body. See Fig. 1.
GOVERNOR PRESSURE SOLENOID
Governor pressure solenoid generates governor pressure
required for transmission upshifts and downshifts. Governor pressure
solenoid is located on valve body. See Fig. 1. Inlet side of governor
pressure solenoid is exposed to normal transmission line pressure and
outlet side provides a passage to governor circuit in the valve body.
Governor pressure solenoid regulates transmission line pressure to the
governor circuit. Electrical supply voltage is supplied to governor
pressure solenoid by PCM. The PCM controls the ground circuit to
governor pressure solenoid to provide solenoid operation.
Fig. 1: Identifying Governor Pressure Solenoid, Governor Pressure
Sensor & Transmission Fluid Temperature Sensor
Courtesy of DaimlerChrysler Corp.
OD (OVERDRIVE) OFF SWITCH

The OD (Overdrive) OFF switch is located on instrument panel,\
to the right of steering column. The OD OFF switch controls overdrive
operation by delivering an input signal to PCM. The PCM uses this
signal for controlling operation of overdrive solenoid on the valve
body.
When overdrive switch is in the OFF position, OD light on
instrument panel will be illuminated and transmission will not upshift
into 4th gear for overdrive operation. When OD switch is in the ON
position, OD light on instrument panel will not be illuminated and
transmission will upshift into 4th gear for overdrive operation.
If OD switch is in the ON position, the TCC will lock-up when
transmission is in 4th gear with vehicle speed greater than 45 MPH. If
overdrive switch is in the OFF position, the TCC will lock-up when
transmission is in 3rd gear with vehicle speed greater than 35 MPH at
light throttle application.
THROTTLE POSITION (TP) SENSOR
The TP sensor delivers an input signal to the PCM to indicate
throttle position. The PCM uses this input signal for controlling TCC
operation, governor pressure and upshift into 4th gear for overdrive
operation.
TRANSMISSION FLUID TEMPERATURE SENSOR
NOTE: Transmission fluid temperature sensor may also be referred to
as transmission fluid temperature thermistor or transmission
fluid temperature sender.
Transmission fluid temperature sensor delivers an input
signal to the PCM to indicate transmission fluid temperature. The PCM
uses this input signal for controlling the TCC, overdrive operation
and governor pressure. Transmission fluid temperature sensor is
located on the valve body and is integral with governor pressure
sensor. See Fig. 1.
OUTPUT SHAFT SPEED SENSOR
NOTE: Output shaft speed sensor may also be referred to as
transmission shaft speed sensor or shaft speed sensor.
Output shaft speed sensor is located on overdrive unit
attached to rear of transmission. Output shaft speed sensor is mounted
above the lugs on park gear in the overdrive unit. Speed sensor input
signals are generated when lugs on park gear rotate past face of
sensor. Input signals are delivered to PCM. The PCM uses this input
signal for controlling transmission operation. The Vehicle Speed
Sensor (VSS) also serves as a back-up to the output shaft speed
sensor. The VSS signal is also an input to the PCM.
TROUBLE SHOOTING
* PLEASE READ THIS FIRST *
NOTE: For symptom trouble shooting, see appropriate AUTOMATIC
TRANSMISSION OVERHAUL article.
PRELIMINARY INSPECTION
Visually inspect all electrical wiring, looking for chafed,

stretched, cut or pinched wiring. Ensure electrical connectors fit
tightly and are not corroded. Check PCM, sensors and switches for
physical damage. Check engine coolant level. Check transmission fluid
level and condition.
SELF-DIAGNOSTIC SYSTEM
* PLEASE READ THIS FIRST *
NOTE: Only transaxle-related trouble codes are listed. For engine-
related DTC definitions, see TROUBLE CODE DEFINITIONS article
in APPLICATIONS & IDENTIFICATION. For engine-related DTC
diagnosis, see appropriate SELF-DIAGNOSTICS article in ENGINE
PERFORMANCE. Engine performance DTCs must be repaired first,
as engine performance and related component signals will
affect transaxle operation and diagnosis.
DIAGNOSTIC PROCEDURE
When performing vehicle diagnosis:
* Ensure transmission fluid level is correct and fluid is
neither contaminated or aerated.
* Ensure shift cable is properly adjusted. See appropriate
AUTOMATIC TRANSMISSION SERVICING article in TRANSMISSION
SERVICING.
* Ensure battery is fully charged.
* Perform visual inspection, ensuring all electrical
connections at transmission, PCM, TP sensor and output shaft
speed sensor are clean and properly installed.
* Retrieve DTCs. See RETRIEVING DIAGNOSTIC TROUBLE CODES.
* Repair DTCs in order displayed.
* Always perform test verification test after any repair
procedure is completed unless specified otherwise. See
appropriate verification test under DIAGNOSTIC TESTS.
NOTE: Self-diagnostic tests are written specifically for Chrysler's
Diagnostic Readout Box (DRB) scan tool. A generic scan tool
may be used, but may not be capable of performing all
necessary test functions.
TEST EQUIPMENT HOOK-UP
Generic Scan Tool & DVOM
Self-diagnostic tests are written specifically for Chrysler's
Diagnostic Readout Box (DRB) scan tool. The DRB has a built-in DVOM
function. A generic scan tool may be used, but may not be capable of
performing all necessary test functions. If DRB test procedures
require resistance or voltage to be measured using scan tool in
ohmmeter or voltmeter mode, connect DVOM ground lead to DLC connector
terminal No. 4 and positive lead to terminal specified in test
procedure.
DRB Scan Tool
Refer to DRB scan tool instructions to read and clear DTCs,
and when performing other scan tool functions. DRB scan tool is
grounded through DLC connector terminal No. 4. Only one volt/ohmmeter
test lead is required to measure voltage or resistance. See Fig. 2.
RETRIEVING DIAGNOSTIC TROUBLE CODES
NOTE: Manufacturer recommends using Chrysler's Diagnostic Readout