1999 DODGE RAM recommended oil

   











\








\









\









\








\









\









\





\f

Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   











\








\









\









\








\









\









\





\f

Fuel Tank  Capacity  35 Gal. (132L) 











\










\









\









\









\









\









\




\f



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 










\









\









\









\









\









\









\







LUBRICATION SPECIFICATIONS - GAS
LUBRICATION SPECIFICATIONS TABLE - GAS







\





 



\









\









\








 \









\









\





 
Material  Condition  Specification 











\








\









\









\








\









\









\





\f

Engine Oil Ambient Temperature Above 0 \bF SAE 10W-30 

(
1)  (-18\bC) To Over 100\bF (38\bC)  












\









\









\








\









\









\
\f

Ambient Temperature Less Than  SAE 5W-30 

-20\bF (-29\bC) Up To 32\bF (0\bC) 











\








\









\









\








\









\









\





\f

Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 











\








\









\









\








\









\









\





\f

Brake Fluid  All  DOT 3 











\








\









\









\








\









\









\





\f

Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   











\








\









\









\








\









\









\





\f

Transfer Case All  ATF+2 Type 7176 

Fluid   Or DEXRON III ATF 











\








\









\









\








\









\









\





\f

Manual  NV-4500 75W-90 Synthc. API GL4 

Transmission










\









\









\








\









\









\
\f

Fluid  NV-3500  Mopar Manual 

  Transmission Fluid 











\








\









\









\








\









\









\





\f

Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   











\








\









\









\








\









\









\





\f

Wheel Bearing All High Temperature Multi-

Grease   -Purporse EP Grease 











\








\









\









\








\









\









\





\f

Rear Axle &  All Mopar Hypoid Lubricant 

4x4 Frt. Axle  SAE 80W-90 

Lubricant (
2)  GL-5 Gear Lube 











\








\









\









\








\









\









\





\f

Power  All  Mopar Power Steering 

Steering   Fluid Or Equivalant 

Fluid (
3)   Petroleum Based 











\








\









\









\








\









\









\





\f

Clutch  All  Multipurpose Grease 

Linkage   NLGI Grade 2 E.P. 

Lubricant   











\








\









\









\








\









\









\





\f

A/C  All  R-134a 

Limited Slip









\









\









\








\









\









\
\f

Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 












\









\









\








\









\









\
\f

 Model 267 (2WD)  7 Pts. (3.3L) 












\









\









\








\









\









\
\f

 Model 267 (4WD)  7.8 Pts. (3.6L) 












\









\









\








\









\









\
\f

 Model 286 (2WD)  6.8 Pts. (3.2L) 












\









\









\








\









\









\
\f

 Model 286 (4WD)  10.1 Pts. (4.8L) 











\








\









\









\








\









\









\





\f

Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant










\









\









\








\









\









\
\f

 Model 248  7.6 Pts. (3.6L) 











\








\









\









\








\









\









\





\f

Transfer Case NV231 HD  2.5 Pts. (1.2L) 

Fluid   











\








\









\









\








\









\









\





\f

Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   











\








\









\









\








\









\









\





\f

Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   











\








\









\









\








\









\









\





\f

A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  











\








\









\









\








\









\









\





\f

Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   











\








\









\









\








\









\









\





\f

Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L) 












\









\









\








\









\









\
\f

 All Others  35 Gal. (132L) 











\










\









\









\









\









\









\




\f

(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 










\









\









\









\









\









\









\







WHEEL & TIRE SPECIFICATIONS
TIRE REPLACEMENT
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for wear and
correct inflation pressure. Chrysler strongly recommends that you use
tires equivalent to the originals in quality and performance when
replacement is needed. Failure to use equivalent replacement tires may
adversely affect the safety, handling and ride of your vehicle. We
recommend that you contact your original equipment tire dealer on any
questions you may have on tire specifications or capability.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\







Lug Nut Ft. Lbs. (N.m)
BR1500 (5 Stud Wheel) ........................... 95 (130)
BR2500 (8 Stud Wheel) ........................... 135 (180)

CAUTION: If fuel contamination due to fungi or other microorganisms is
suspected a fuel additive with a biocide may be used. Follow
the manufacturers dosage as recommended on product label. Use
biocides ONLY when necessary, excessive use can may cause
other fuel system problems.
DIESEL FUEL CONTAMINATION
WARNING: Diesel fuel system may be contaminated with fungi or other
microorganisms. Keep contaminated fuel away from open skin
cuts or sores to prevent skin irritation or infection.
DIESEL FUEL REQUIREMENTS
CAUTION: All diesel engines have been developed to take advantage of
the high energy content of No. 2 diesel fuel or No. 2
climatized-diesel fuels. It also operates on No. 1-diesel
fuels if temperatures are expected to be extended arctic
conditions -10
\bF (-23\bC).
WARNING: Do NOT use alcohol or gasoline as a fuel blending agent. They
can be unstable under certain conditions and hazardous or
explosive when mixed with diesel fuel.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
ENGINE OIL FILTER (CARTRIDGE TYPE)
CAUTION: Use of Mopar Oil Filter Cartridge (P/N 04746914) is
RECOMMENDED. The engine oil filter cartridge should be
changed at every engine oil change. Use the same type oil
that will be used in the engine.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.

 Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


12,000 MILE (19,000 KM)/12 MONTH NORMAL SERVICE
12,000 MILE (19,000 KM)/12 NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Water Pump Weep Hole For Blockage 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Clean Fuel Strainer 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 


\
\
\
\
\
\
\


 Fuel Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


18,000 MILE (29,000 KM)/18 MONTH NORMAL SERVICE
18,000 MILE (29,000 KM)18 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


  Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Brake Linings 


\
\
\
\
\
\
\


 Drive Belts 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


 Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\

\
\
\

\
\
\


Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   

\

\
\
\

\
\
\


Wheel Bearing All High Temperature Multi-

Grease   -Purporse EP Grease 

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE
30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


  Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


36,000 MILE (58,000 KM)/36 MONTH NORMAL SERVICE
36,000 MILE (58,000 KM)/36 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Brake Linings