1999 DODGE RAM recommended oil

2.4L ............................. 170-225 psi (11.9-15.7 kg/cm)
3.0L ...................................... 178 psi (12.5 kg/cm)
3.3L ........................................................ ( 1)
Minimum Compression Pressure
Caravan, Town & Country, & Voyager .......... 100 psi (7.0 kg/cm
)
Dakota
2.5L ........................................................ ( 1)
3.9L, 5.2L & 5.9L .......................... 100 psi (7.0 kg/cm
)
Durango ..................................... 100 psi (7.0 kg/cm)
Ram Pickup
3.9L, 5.2L & 5.9L (Gasoline) & 8.0L ........ 100 psi (7.0 kg/cm
)
5.9L (Diesel) ............................................... ( 1)
Ram Van & Ram Wagon ......................... 100 psi (7.0 kg/cm
)
Maximum Variation Between Cylinders
Caravan, Town & Country & Voyager ..................... 25 Percent
Dakota
2.5L ........................................ 30 psi (2.1 kg/cm
)
3.9L, 5.2L & 5.9L ........................................... ( 1)
Durango ...................................................... ( 1)
Ram Pickup, Ram Van & Ram Wagon .............................. ( 1)
( 1) - Information is not available from manufacturer.









\









\









\









\









\









\









\







VALVE CLEARANCE
Gasoline Models
All engines are equipped with hydraulic lifters. No
adjustments are required.
5.9L Diesel (Ram Pickup)
Valve adjustment is recommended every 150 months or 150,000
miles during normal service, every 135,000 miles during severe
service. Severe service is described as frequent short trip operation
of less than 5 miles, long periods of engine idling, trailer towing,
police, taxi, local delivery service, or operating in dusty or
excessively hot conditions. See VALVE CLEARANCE SPECIFICATIONS
(DIESEL) table.
VALVE CLEARANCE SPECIFICATIONS (DIESEL) ( 1)









\









\









\









\









\









\









\







Application In. (mm)\
Intake Valve ............................................ .010 (.25)\
Exhaust Valve ........................................... .020 (.51)\
(1) - Adjust valves with engine temperature less than 140
F (60C).








\









\









\









\









\









\









\







IGNITION SYSTEM
IGNITION COIL
IGNITION COIL RESISTANCE - Ohms @ 70-80F (21-27C)








\









\









\









\









\









\









\







Application Primary Secondary
Caravan
2.4L
Diamond ( 1)( 2) ............... .53-.65 .......... 11,500-13,500
Weastec ( 1) .................. .45-.65 .......... 10,900-14,700
3.0L ............................. ( 3) ..................... ( 3)

(1) - Approximate quantity listed.








\









\









\









\









\









\









\







DRAINING & FILLING
Transmission
1) Raise and support vehicle. Loosen oil pan bolts, allowing
fluid to drain from oil pan. Remove oil pan bolts, oil pan and gasket.
Remove oil filter bolts and oil filter from valve body.
2) Adjust kickdown band and low-reverse bands if necessary.
See KICKDOWN BAND and LOW-REVERSE BAND under ADJUSTMENTS.
3) Clean oil pan, magnet and all sealing surfaces. Install
NEW oil filter. Install and tighten oil filter bolts to specification.
See TORQUE SPECIFICATIONS.
4) Using NEW gasket, install oil pan. Install and tighten oil
pan bolts to specification. See TORQUE SPECIFICATIONS.
5) Add Mopar ATF Plus Type 7176 fluid until fluid level is at
MIN arrow mark on dipstick. Start engine and allow engine to idle.
With brakes applied, shift transmission through all gears and back to
Neutral.
6) Add additional fluid to bring fluid level to MIN mark on
dipstick. Recheck fluid level with transmission at normal operating
temperature. Adjust fluid level to MAX arrow mark on dipstick. DO NOT
overfill transmission.
Transfer Case
1) Ensure vehicle is parked on level surface. Remove transfer
case drain plug. Transfer case drain plug is located on rear of
transfer case at driver's side corner of transfer case. Allow fluid to
drain from transfer case.
2) Reinstall transfer case drain plug. Tighten transfer case
drain plug to specification. See TORQUE SPECIFICATIONS. Remove
transfer case fill plug from rear of transfer case. Transfer case fill
plug is located on rear of transfer case, just below identification
tag.
3) Fill transfer case with appropriate type of transfer case
fluid until fluid level is even with bottom of fill plug hole on
transfer case. See RECOMMENDED FLUID. Install and tighten transfer
case fill plug to specification. See TORQUE SPECIFICATIONS.
Power Take-Off (PTO) Adapter (Ram Pickup 2WD 2500 & 3500)
1) Ensure vehicle is parked on level surface. Remove drain
plug from rear of PTO adapter. See Fig. 3. Allow fluid to drain from
PTO adapter.
2) Reinstall drain plug. Tighten drain plug to specification.
See TORQUE SPECIFICATIONS. Remove fill plug from rear of PTO adapter.
See Fig. 3 .
3) Fill PTO adapter with appropriate type of fluid until
fluid level is even with bottom of fill plug hole on PTO adapter. See
RECOMMENDED FLUID. Install and tighten fill plug to specification. See
TORQUE SPECIFICATIONS.
ADJUSTMENTS
KICKDOWN BAND
1) Kickdown band is front band on transmission. Raise and
support vehicle. Loosen kickdown band adjusting screw lock nut while
preventing kickdown adjusting screw from rotating. Kickdown band
adjusting screw is located on side of transmission, near manual lever
shaft. See Fig. 4.
2) Back off kickdown band adjusting screw lock nut 5 turns.

Transmission (Dakota)
Check transmission fluid level when performing other
underhood services. Under normal service conditions, change
transmission fluid at 30 months or 37,500 miles. Under severe service
conditions, change transmission fluid at 18,000 miles. Severe service
are conditions such as long periods of engine idling, trailer towing,
off-highway operation, snow removal, or operating in dusty or
excessively hot conditions.
Transmission (Ram Pickup)
Check transmission fluid level when performing other
underhood services. Fluid change service interval information is not
available from manufacturer.
Transfer Case
Check transfer case fluid level when performing other
underhood services. On Dakota and Light-Duty Pickup, change transfer
case fluid at 37,500 miles or 30 months. On Medium-Duty and Heavy-Duty
Pickup, change transfer case fluid at 36,000 miles or 36 months.
CHECKING FLUID LEVEL
Transmission (Dakota)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On AX-15 transmission, transmission
fill plug is located on driver's side of transmission. On NV3500
transmission, transmission fill plug is located near front of
transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transmission (Ram Pickup)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On NV3500 transmissions, transmission
fill plug is located near front of transmission on passenger's side of
transmission. On NV4500 transmissions, transmission fill plug is
located near rear of transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transfer Case
Park vehicle on level surface. Remove transfer case fill plug
from rear of transfer case. Fluid level should even with bottom of
transfer case fill plug hole on rear of transfer case. Add appropriate
type of transfer case fluid if necessary. See RECOMMENDED FLUID.
Install and tighten transfer case fill plug to specification. See
TORQUE SPECIFICATIONS.
RECOMMENDED FLUID
Transmission (Dakota)
On AX-15 transmissions, use API 75W-90 GL-3 gear oil. On
NV1500 and NV3500 transmissions, use ONLY Mopar M/T Lube Part No.
4761526.
Transmission (Ram Pickup)

will need to shift your Lab Scope to five volts per division.
You will find that some systems have slight voltage
fluctuations here. This can occur if the injector feed wire is also
used to power up other cycling components, like the ignition coil(s).
Slight voltage fluctuations are normal and are no reason for concern.
Major voltage fluctuations are a different story, however. Major
voltage shifts on the injector feed line will create injector
performance problems. Look for excessive resistance problems in the
feed circuit if you see big shifts and repair as necessary.
Note that circuits with external injector resistors will not
be any different because the resistor does not affect open circuit
voltage.
Point "B" is where the driver completes the circuit to
ground. This point of the waveform should be a clean square point
straight down with no rounded edges. It is during this period that
current saturation of the injector windings is taking place and the
driver is heavily stressed. Weak drivers will distort this vertical
line.
Point "C" represents the voltage drop across the injector
windings. Point "C" should come very close to the ground reference
point, but not quite touch. This is because the driver has a small
amount of inherent resistance. Any significant offset from ground is
an indication of a resistance problem on the ground circuit that needs
repaired. You might miss this fault if you do not use the negative
battery post for your Lab Scope hook-up, so it is HIGHLY recommended
that you use the battery as your hook-up.
The points between "B" and "D" represent the time in
milliseconds that the injector is being energized or held open. This
line at Point "C" should remain flat. Any distortion or upward bend
indicates a ground problem, short problem, or a weak driver. Alert
readers will catch that this is exactly opposite of the current
controlled type drivers (explained in the next section), because they
bend upwards at this point.
How come the difference? Because of the total circuit
resistance. Voltage controlled driver circuits have a high resistance
of 12+ ohms that slows the building of the magnetic field in the
injector. Hence, no counter voltage is built up and the line remains
flat.
On the other hand, the current controlled driver circuit has
low resistance which allows for a rapid magnetic field build-up. This
causes a slight inductive rise (created by the effects of counter
voltage) and hence, the upward bend. You should not see that here with
voltage controlled circuits.
Point "D" represents the electrical condition of the injector
windings. The height of this voltage spike (inductive kick) is
proportional to the number of windings and the current flow through
them. The more current flow and greater number of windings, the more
potential for a greater inductive kick. The opposite is also true. The
less current flow or fewer windings means less inductive kick.
Typically you should see a minimum 35 volts at the top of Point "D".
If you do see approximately 35 volts, it is because a zener
diode is used with the driver to clamp the voltage. Make sure the
beginning top of the spike is squared off, indicating the zener dumped
the remainder of the spike. If it is not squared, that indicates the
spike is not strong enough to make the zener fully dump, meaning the
injector has a weak winding.
If a zener diode is not used in the computer, the spike from
a good injector will be 60 or more volts.
Point "E" brings us to a very interesting section. As you
can see, the voltage dissipates back to supply value after the peak of
the inductive kick. Notice the slight hump? This is actually the
mechanical injector pintle closing. Recall that moving an iron core
through a magnetic field will create a voltage surge. The pintle is

drivers. They typically require injector circuits
with a total leg resistance with less than 12 ohm.
NOTE: This example is based on a constant power/switched ground
circuit.
* See Fig. 3 for pattern that the following text describes.
Point "A" is where system voltage is supplied to the
injector. A good hot run voltage is usually 13.5 or more volts. This
point, commonly known as open circuit voltage, is critical because the
injector will not get sufficient current saturation if there is a
voltage shortfall. To obtain a good look at this precise point, you
will need to shift your Lab Scope to five volts per division.
You will find that some systems have slight voltage
fluctuations here. This could occur if the injector feed wire is also
used to power up other cycling components, like the ignition coil(s).
Slight voltage fluctuations are normal and are no reason for concern.
Major voltage fluctuations are a different story, however. Major
voltage shifts on the injector feed line will create injector
performance problems. Look for excessive resistance problems in the
feed circuit if you see big shifts and repair as necessary.
Point "B" is where the driver completes the circuit to
ground. This point of the waveform should be a clean square point
straight down with no rounded edges. It is during this period that
current saturation of the injector windings is taking place and the
driver is heavily stressed. Weak drivers will distort this vertical
line.
Point "C" represents the voltage drop across the injector
windings. Point "C" should come very close to the ground reference
point, but not quite touch. This is because the driver has a small
amount of inherent resistance. Any significant offset from ground is
an indication of a resistance problem on the ground circuit that needs
repaired. You might miss this fault if you do not use the negative
battery post for your Lab Scope hook-up, so it is HIGHLY recommended
that you use the battery as your hook-up.
Right after Point "C", something interesting happens. Notice
the trace starts a normal upward bend. This slight inductive rise is
created by the effects of counter voltage and is normal. This is
because the low circuit resistance allowed a fast build-up of the
magnetic field, which in turn created the counter voltage.
Point "D" is the start of the current limiting, also known as
the "Hold" time. Before this point, the driver had allowed the current
to free-flow ("Peak") just to get the injector pintle open. By the
time point "D" occurs, the injector pintle has already opened and the
computer has just significantly throttled the current back. It does
this by only allowing a few volts through to maintain the minimum
current required to keep the pintle open.
The height of the voltage spike seen at the top of Point "D"
represents the electrical condition of the injector windings. The
height of this voltage spike (inductive kick) is proportional to the
number of windings and the current flow through them. The more current
flow and greater number of windings, the more potential for a greater
inductive kick. The opposite is also true. The less current flow or
fewer windings means less inductive kick. Typically you should see a
minimum 35 volts.
If you see approximately 35 volts, it is because a zener
diode is used with the driver to clamp the voltage. Make sure the
beginning top of the spike is squared off, indicating the zener dumped
the remainder of the spike. If it is not squared, that indicates the
spike is not strong enough to make the zener fully dump, meaning there
is a problem with a weak injector winding.
If a zener diode is not used in the computer, the spike from