1999 DODGE RAM flat tire

length gas tank size fuse box location steering wheel towing brake pads replacement

Page 1305 of 1691

DODGE RAM 1999 Service Repair Manual Condition Code Procedure
Air pressure incorrect .. B .................. Require repair
Bead broken ............. A ............ Require replacement.
Be

Condition Code Procedure
Air pressure incorrect .. B .................. Require repair
Bead broken ............. A ............ Require replacement.
Bead leaking, caused
by tire ................ A .. Require repair or replacement.
Bead wire/cord exposed .. A ............ Require replacement.
Cord or belt material
exposed ................ A ............ Require replacement.
Cord ply separations .... A ............ Require replacement.
Directional/asymmetrical
tires mounted
incorrectly ............ B ....... Require remounting and/or
repositioning.
Irregular tread wear,
affecting performance .. 2 ........ (1) Suggest replacement.
Load ratings less
than OEM
specifications ......... B ............ Require replacement.
Mixed tread types (all
season, performance, mud
and snow) on same axle . A ............ Require replacement.
Number of punctures
exceeds manufacturer's
limit .................. B ............ Require replacement.
Out of balance .......... B . Require rebalance of tire/wheel
assembly.
Ply separation .......... A ............ Require replacement.
Pull or lead, caused
by tire ................ A .. Require repair or replacement.
Radial and bias or
bias-belted ply tires
on same axle ........... B .. Require repair or replacement.
Radials are on the front
and not on the rear .... B ........... ( 2) Require repair or
replacement.
Run flat damage ......... A ............ Require replacement.
Shoulder cut ............ A ............ Require replacement.
Shoulder puncture ....... A ............ Require replacement.
Shoulder with plug ...... A ............ Require replacement.
Sidewall bulge .......... A ............ Require replacement.
Sidewall cut ............ A ............ Require replacement.
Sidewall indentation .... .. ......... No service required or
suggested.
Sidewall puncture ....... A ............ Require replacement.
Sidewall with plug ...... A ............ Require replacement.
Speed rating
designations
different
on same axle ........... 2 .. Suggest repair or replacement.
Tire and wheel assembly
has excessive run-out .. B ........... ( 3) Require repair or
replacement of appropriate
part.
Tires with more than
1/4" diameter difference
on a four-wheel drive
vehicle ................ B ............ Require replacement.
Tread area puncture larger
in diameter than
manufacturer's
specifications ......... B ............ Require replacement.
Tread missing pieces

Page 1346 of 1691

DODGE RAM 1999 Service Repair Manual (1) - Require replacement of units where dents restrict shock
or strut piston rod movement. If dents dont restrict
movement, no service is suggested or required. Especially
critical

(1) - Require replacement of units where dents restrict shock
or strut piston rod movement. If dents don't restrict
movement, no service is suggested or required. Especially
critical on mono-tube shocks.
( 2) - This condition can lead to damage of the piston rod,
which, in turn, causes premature piston rod seal wear.
( 3) - Only required if replacing cartridge.
( 4) - CAUTION: If the strut cartridge has been replaced previously,
the oil on the strut housing may be filler oil. The
technician must identify the source of the oil.
( 5) - If noise is isolated to shock or strut, suggest
replacement.
( 6) - Although shocks or struts may have contributed to tire
cupping, an inspection is needed of the entire suspension
system. If the shock or strut is found to be contributing
to the tire cupping, require replacement.
\
\
\
\
\
\
\

SPINDLES
SPINDLE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Race seat area
undersized ............. B ............ Require replacement.
Scored .................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\

SPRINGS - COIL, LEAF AND TORSION BAR
When springs are replaced, it is suggested, but not required,
that both springs on an axle be replaced to maintain equal height from
side to side and to provide a balanced ride and proper handling.
When variable rate springs are installed in place of
conventional coil springs, they must be installed in axle sets to
ensure proper handling, uniform ride, and proper chassis height.
Erroneous height measurements may result from: improper tire
inflation, non-standard tire or wheel size, and heavy load in vehicle
or trunk.
SPRING (COIL, LEAF AND TORSION BAR) INSPECTION

Page 1364 of 1691

DODGE RAM 1999 Service Repair Manual be caused by
faulty alignment ....... A ............. Require alignment.
Part has been changed,
affecting alignment .... A ....... Require alignment check.
Pull, shown to be caused
by faul

be caused by
faulty alignment ....... A ............. Require alignment.
Part has been changed,
affecting alignment .... A ....... Require alignment check.
Pull, shown to be caused
by faulty alignment .... A ............. Require alignment.
Steering wheel
off-center ............. 2 ............. Suggest alignment.
Tire wear, shown
to be caused by
faulty alignment ....... A ............. Require alignment.
Wander, shown
to be caused by
faulty alignment ....... A ............. Require alignment.
\
\
\
\
\
\
\

WHEELS AND TIRES
TIRES
These guidelines do not apply to split rims. Some vehicle
manufacturers restrict replacement of tires to specific brands, types,
or sizes.
WARNING: High pressure temporary compact spare tires should not be
used with any other rims or wheels, nor should standard
tires, snow tires, wheel covers, or trim rings be used
with high pressure compact spare rims or wheels.
Attempting to mount a tire of one diameter on a wheel of
a different diameter or flange type may result in serious
injury or death.
WARNING: Only specially trained persons should dismount or mount
tires. Explosions of tire and wheel assembly can result
from improper mounting, possibly causing serious injury
or death.
WARNING: Consult the vehicle owner's manual or vehicle placard for
correct size, speed rating, designation, and cold
inflation pressure of the original tires. DO NOT exceed
the maximum load or inflation capacity of the tire
specified by the Tire and Rim Association
WARNING: When replacing tires, it is suggested that the
replacement tires match or exceed the OEM speed rating
designation. If tires of different speed rating
designations are mixed on the same vehicle, the tires may
vary in handling characteristics. DO NOT mix different
speed rating designations on the same axle.
WARNING: DO NOT mix radials with non-radial tires on the same
axle, as this may affect vehicle handling and stability.
If radial tires and bias or bias-belted ply tires are
mixed on the same vehicle, the radials must be on the
rear. High-pressure temporary compact spare tires are
exempt from this rule.
WARNING: DO NOT mix size or type (all season, performance, mud and
snow) of tires on the same axle.
TIRE INSPECTION
\
\
\
\
\
\
\

Page 1365 of 1691

Page 1570 of 1691

DODGE RAM 1999 Service Repair Manual WHEEL A LIG NM EN T S PEC IF IC ATIO NS

1999 D odge P ic ku p R 1500
1998-99 WHEEL ALIGNMENT
CHRY - Specifications & Procedures - Trucks & FWD Vans
Caravan, Dakota, Du

WHEEL A LIG NM EN T S PEC IF IC ATIO NS

1999 D odge P ic ku p R 1500
1998-99 WHEEL ALIGNMENT
CHRY - Specifications & Procedures - Trucks & FWD Vans
Caravan, Dakota, Durango, Ram Pickup, Ram Van/Wagon,
Town & Country, Voyager
NOTE: Prior to performing wheel alignment, perform visual and
mechanical inspection of wheels, tires and suspension
components. See PRE-ALIGNMENT INSTRUCTIONS in WHEEL ALIGNMENT
THEORY & OPERATION article in GENERAL INFORMATION.
RIDING HEIGHT ADJUSTMENT
CHECKING PROCEDURE
NOTE: Information on vehicles not listed was not available from
manufacturer.
1999 Caravan, Town & Country, & Voyager
Before adjusting alignment, check riding height. Measure
height from inboard edge of fenderwell directly above center of wheel,
unless specified otherwise. Riding height must be checked with vehicle
on level floor, correct size tires properly inflated and fuel tank
full. Bounce vehicle several times and allow suspension to settle.
Visually inspect vehicle for signs of abnormal height from
front-to-rear and side-to-side. Check passenger and luggage
compartments for extra-heavy items and remove if present. Riding
height between left side and right side of vehicle should vary less
than 0.5 (12.7 mm). Information on riding height between front and
rear is not available from manufacturer. See RIDING HEIGHT
SPECIFICATIONS (1999 CARAVAN, TOWN & COUNTRY, & VOYAGER) table. If
riding height is not within specification, check, repair or replace
suspension components.
Dakota & Durango (4WD)
1) Measure and record distance between floor surface and
center of lower suspension arm rear mounting bolt head. Measure and
record distance between floor surface and center of front wheel. See
Fig. 1 . Subtract first measurement from second measurement. On Dakota,
difference between both measurements should be 1.725-1.975" (43.82-50.
16 mm). On Durango, difference between both measurements should be 2.
78-3.02" (70.6-76.7 mm).
2) If necessary, adjust height differential to specification.
Adjust each front suspension arm by rotating torsion bar anchor
adjustment bolt clockwise to raise vehicle and counterclockwise to
lower vehicle. Always raise vehicle to correct height. If vehicle
height is greater than maximum specification, lower height to less
than specification, then back up to specification. After each
adjustment, jounce vehicle before measuring height to determine
effects of adjustment.

Page 1585 of 1691

DODGE RAM 1999 Service Repair Manual
WHEEL A LIG NM EN T T H EO RY/O PER ATIO N

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Wheel Alignment Theory & Operation
ALL MODELS
* PLEASE READ THIS

Page: < prev 1-8 9-16

diagram turn signal bulb immobilizer fuel filter warning light seat adjustment