1999 DODGE RAM steering

2) Apply voltage to Light Blue/Yellow wire at heated mirror
and ground Black wire at heated mirror. Mirror should become warm to
touch. If mirror is not warm to touch, remove mirror and test wires
for continuity. If no continuity exists, repair wires. If wires are
okay, replace mirror. To test defogger switch, see appropriate wiring
diagram in REAR WINDOW DEFOGGERS article.
NOTE: On Ram Pickup, heated mirror is controlled by mirror defogger
switch.
Ram Pickup
1) Turn ignition on. While watching instrument panel
voltmeter, turn heated mirror switch on. Voltmeter needle should
deflect. With heated mirror on, mirror should be warm to touch after
3-4 minutes. If system operates as described, system is okay at this
time.
2) If system does not operate as described, go to next step.
Illuminated indicator light means only that voltage exists at heated
mirror relay.
3) Ensure ignition is on. Check fuses in Power Distribution
Center (PDC) and junction block. Ensure fuses are fully seated and
connections are secure. If mirrors are still inoperative, problem is
in heated mirror control, mirror heating grid and/or heated mirror
harness or connectors. If turning switch on causes a large deflection
in instrument panel voltmeter, check for a short circuit in system.
Repair as necessary.
REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
HEATED MIRROR SWITCH
Removal & Installation (Ram Pickup)
Heated mirror switch is part of HVAC control unit. See
appropriate AUTOMATIC A/C-HEATER SYSTEMS article in appropriate AIR
CONDITIONING & HEATING SERVICE & REPAIR section.
POWER MIRROR SWITCH
Removal & Installation (Caravan, Town & Country, & Voyager)
1) Remove cover from over steering column. Remove screws
holding instrument cluster bezel to dash (above cluster lens). Remove
screws holding instrument cluster bezel to dash from each side of
steering column. Disconnect clip holding instrument cluster bezel to
dash from above right vent louver.
2) Separate instrument cluster bezel from dash. Disconnect
wires from back of bezel. Disengage lock tabs above and below mirror
switch. Pull mirror switch from headlight switch bezel. To install,
reverse removal procedure.
Removal & Installation (Dakota & Durango)
1) Pull power mirror switch control knob rearward to remove
it from switch body. Remove nut securing switch to door trim panel.
Pull door latch handle to open position and remove screw securing trim
panel to door. Remove manual window crank handle, if equipped. Release
locking tab on power window/lock switch, if equipped. Remove power
window/lock switch and unplug connector.

bracket. Ensure alignment tab on brake switch aligns with opening on
mounting bracket.
CAUTION: When adjusting brake switch, DO NOT pull brake pedal back
toward brake switch with excessive pressure, or brake switch
may be damaged.
3) When brake switch is fully installed in mounting bracket,
rotate brake switch clockwise approximately 30 degrees. To ensure
proper brake switch adjustment, gently pull brake pedal back toward
brake switch as far as possible. DO NOT apply excessive pressure on
brake pedal and brake switch.
Removal (Ram Van & Ram Wagon)
1) Brake switch is located near top of brake pedal. Remove
lower steering column cover. Remove data link connector, hood release
lever and parking brake lever from lower instrument panel cover.
2) Remove lower instrument panel cover for access to brake
switch. Depress and hold brake pedal downward. Rotate brake switch
counterclockwise approximately 1/16 turn to so locking collar on brake
switch aligns with opening on mounting bracket. Pull brake switch
rearward from mounting bracket. Disconnect electrical connector from
brake switch.
NOTE: Before installing brake switch, plunger on brake switch must
be pulled outward to fully extended position and then pushed
inward 4 detent positions to ensure proper brake switch
adjustment.
Installation
1) Pull plunger on brake switch outward to the fully extended
position. Push plunger on brake switch inward 4 detent positions. The
brake switch will click at each detent position when pushing plunger
inward.
2) Install electrical connector on brake switch. Depress
brake pedal as far as possible. Install brake switch in mounting
bracket. Ensure locking collar on brake switch aligns with opening on
mounting bracket.
CAUTION: When adjusting brake switch, DO NOT pull brake pedal back
toward brake switch with excessive pressure, or brake switch
may be damaged.
3) When brake switch is fully installed in mounting bracket,
rotate brake switch clockwise approximately 1/16 turn. To ensure
proper brake switch adjustment, gently pull brake pedal back toward
brake switch as far as possible. DO NOT apply excessive pressure on
brake pedal and brake switch.
CAMSHAFT POSITION SENSOR
Removal & Installation
See CAMSHAFT POSITION SENSOR under IGNITION SYSTEM.
CRANKSHAFT POSITION SENSOR
Removal & Installation
See CRANKSHAFT POSITION SENSOR under IGNITION SYSTEM.
DOWNSTREAM OXYGEN SENSOR
NOTE: Downstream oxygen sensor may also be referred to as post
-catalyst oxygen sensor.

NOTE: Park/neutral switch may also be referred to as park/neutral
position switch.
Removal (A/T Models)
Raise and support vehicle. Disconnect 3-pin electrical
connector from park/neutral switch. Park/neutral switch is located on
driver's side of transmission case, near shift linkage. See Fig. 10.
Unscrew park/neutral switch from transmission case. Remove seal ring
from park/neutral switch.
Installation
1) Apply parking brake. Place shift lever in Neutral. Ensure
park/neutral switch operating levers in transmission are centered in
the park/neutral switch opening on transmission case.
2) Using NEW seal ring, install park/neutral switch. Tighten
park/neutral switch to specification. See TORQUE SPECIFICATIONS.
Install electrical connector. Add Mopar Plus 7176 ATF as necessary.
POWER STEERING PRESSURE SWITCH
Removal & Installation (Dakota 2.5L)
1) Power steering pressure switch is located in pressure line
near power steering pump. See Fig. 11. Disconnect electrical connector
at power steering pressure switch.
2) Place small container below power steering pressure switch
to collect power steering fluid. Remove power steering pressure switch
from pressure line while using a back-up wrench to prevent damage to
pressure line.
3) To install, reverse removal procedure. Tighten power
steering pressure switch to specification. See TORQUE SPECIFICATIONS.
Check and fill power steering pump with Mopar Power Steering Fluid if
necessary. DO NOT use ATF in power steering pump.
Fig. 11: Locating Power Steering Pressure Switch (Dakota 2.5L)
Courtesy of Chrysler Corp.
POWER TAKE-OFF (PTO) SWITCH

\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Crankshaft Position Sensor Bolt
2.5L ..................................................... 14 (19)\
3.9L, 5.2L & 5.9L ............................................ (1)
8.0L ......................................................... ( 1)
Downstream Oxygen Sensor ................................... 22 (30)\
Distributor Hold-Down Bolt ................................. 17 (23)\
EVAP Canister-To-Mounting Bracket Nut
Dakota & Durango ......................................... 17 (23)\
Ram Pickup ................................................... ( 2)
Ram Van & Ram Wagon .......................................... ( 3)
Fuel Pump Module Lock Nut
Dakota ................................................... 40 (54)\
Ram Pickup ............................................... 32 (43)\
Ram Van & Ram Wagon ...................................... 40 (54)\
Fuel Rail Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
8.0L ..................................................... 11 (15)\
Fuel Tank Strap Nut
Dakota & Durango ......................................... 40 (54)\
Ram Pickup ............................................... 30 (41)\
Ram Van & Ram Wagon .......................................... ( 5)
IAT Sensor ................................................. 20 (27)\
Park/Neutral Switch ........................................ 25 (34)\
Power Steering Pressure Switch (2.5L) ...................... 16 (22\
)
Spark Plug ................................................. 30 (41)\
Throttle Body Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
Throttle Body Nut (8.0L) ................................... 16 (22\
)
Upper Intake Manifold Bolt (8.0L) ...................... ( 6) 16 (22)
Upstream Oxygen Sensor ..................................... 22 (30)\
Wheel Lug Nut (Dakota & Durango) ......................... 100 (136\
)
INCH Lbs. (N.m)
Air Cleaner Housing-To-Throttle
Body Nut (Dakota & Durango) ............................. 96 (10.8\
)
Camshaft Position Sensor Bolt (8.0L) ...................... 50 (5.6\
)
Engine Coolant Temperature Sensor ........................ 96 (10.8)\
EVAP Canister Mounting Bracket-To
Body Nut (Ram Van & Ram Wagon) .......................... 95 (10.7\
)
EVAP Leak Detection Pump Filter
Bolt (Ram Pickup, Ram Van & Ram Wagon) ................... 65 (7.3\
)
EVAP Leak Detection Pump Bolt ............................. 11 (1.2)\
EVAP Purge Solenoid Nut (Dakota & Durango) ................ 75 (8.5\
)
IAC Motor Bolt ............................................ 60 (6.8)\
Ignition Coil Bolt/Nut
Dakota, Durango, Ram Van & Ram Wagon ......................... ( 7)
Ram Pickup
3.9L, 5.2L & 5.9L ........................................... ( 7)
8.0L .................................................. 90 (10.2)\
MAP Sensor Bolt
Dakota & Durango ........................................ 25 (2.8)\
Ram Pickup
3.9L, 5.2L & 5.9L ...................................... 25 (2.8)\
8.0L ................................................... 20 (2.3)\
Ram Van & Ram Wagon ..................................... 25 (2.8)\
PCM Bolt .................................................. 35 (4.0)\
TP Sensor Bolt ............................................ 60 (6.8)\

SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)

1999 D odge P ic ku p R 1500
1997-99 MAINTENANCE
Chrysler Maintenance & Service Intervals
Diesel Engines
Normal Service
DODGE; RAM PICKUP Cummins Turbo Diesel: 5.9L VIN [D]
* READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS in MAINTENANCE INFORMATION
article in this section.
Introduction
The frequency of scheduled inspection and maintenance
services in this article are based on normal vehicle usage ONLY. The
following Severe conditions are NOT taken into account:
* Frequent short driving less than 5 Miles (8 Km).
* Frequent driving in dusty conditions.
* Frequent trailer towing.
* Extensive idling.
* More than 50% of your driving is at sustained high speeds
during hot weather, above 90
F (32C).
If the vehicle is operated mainly under any of these
conditions, this Normal service schedule article is inadequate. DO NOT
USE. Instead, use the Severe service schedule: See
SCHEDULED SERVICES - NORMAL SERVICE (DIESEL) .
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


 Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


12,000 MILE (19,000 KM)/12 MONTH NORMAL SERVICE
12,000 MILE (19,000 KM)/12 NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Water Pump Weep Hole For Blockage 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Clean Fuel Strainer 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 


\
\
\
\
\
\
\


 Fuel Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


18,000 MILE (29,000 KM)/18 MONTH NORMAL SERVICE
18,000 MILE (29,000 KM)18 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


  Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Brake Linings 


\
\
\
\
\
\
\


 Drive Belts 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\