1999 DODGE RAM ECO mode

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 5.9L: Drained  4.5 Qts. (4.2L) 

\

\
\
\

\
\
\


Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 
\
\
\

\
\


 8.0L: Drained  24 Qts. (22.7L) 

\

\
\
\

\
\
\


Automatic  47RE: Dry Fill  1733 Pts. (815.6L) 

Transmission   

Fluid   

\

\
\
\

\
\
\


Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Fluid 
\
\
\

\
\


 Model 248 (2WD)  6.3 Pts. (3L) 


\
\
\

\
\


 Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


87,000 MILE (139,000 KM) SEVERE DUTY SERVICE
87,000 MILE (139,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 

 Automatic  47RE: Dry Fill  1733 Pts. (815.6L) 

Transmission   

Fluid   

\

\
\
\

\
\
\


Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Fluid 
\
\
\

\
\


 Model 248 (2WD)  6.3 Pts. (3L) 


\
\
\

\
\


 Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


99,000 MILE (156,000 KM) SEVERE DUTY SERVICE
99,000 MILE (156,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\

\
\
\

\
\
\


Transfer Case NV241  5 Pts. (2.7L) 

Fluid 
\
\
\

\
\


 NV241 HD  6.5 Pts. (3.5L) 


\
\
\

\
\


 NV241 HD W/PTO  9 Pts. (4.9L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


111,000 MILE (185,000 KM) SEVERE DUTY SERVICE
111,000 MILE (185,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter (
1) 

\
\
\
\
\
\
\


(
1)  8.0L: Change oil filter at every oil change. 

5.9L: If mileage is less than 6,000 miles (9,600 Km) Yearly, 

replace the oil filter at every oil change. 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 0 F SAE 10W-30 

(
1)  (-18C) To Over 100F (38C)  

SC HED ULE D S ER VIC ES
  


 Model 286 (4WD)  10.1 Pts. (4.8L) 





Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 



 Model 248  7.6 Pts. (3.6L) 



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 



LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE



Material  Condition  Specification 





Engine Oil Ambient Temperature Above 0 F SAE 10W-30 

(
1)  (-18C) To Over 100F (38C)  





Ambient Temperature Less Than  SAE 5W-30 

-20F (-29C) Up To 32F (0C) 





Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 





Brake Fluid  All  DOT 3 





Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   





Transfer Case All  ATF+2 Type 7176 

Fluid   Or DEXRON III ATF 





Manual  NV-4500: All 75W-90 Synthc. API GL4 

Transmission 



Fluid  NV-3500: All  Mopar Manual 

  Transmission Fluid 





Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   





Wheel Bearing All High Temperature Multi-

Grease   -Purporse EP Grease 





Front  All  Mopar Multi-Mileage 

Suspension   Lubricant 

Ball Joints   

Lubricant   





Chassis  All  Mopar Multi-Mileage 

Lubricant   Lubricant 





Rear Axle  All Mopar Hypoid Lubricant 

Lubricant   SAE 80W-90 

(
2)   GL-5 Gear Lube 





4x4 Front  All Mopar Hypoid Lubricant 

Axle   SAE 80W-90 

 \
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\

\
\
\

\
\
\


Transfer Case NV241  5 Pts. (2.7L) 

Fluid 
\
\
\

\
\


 NV241 HD  6.5 Pts. (3.5L) 


\
\
\

\
\


 NV241 HD W/PTO  9 Pts. (4.9L) 

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L) 


\
\
\

\
\


 All Others  35 Gal. (132L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, Inspect and clean wiper blades as required.
* Twice a year, lubricate the external lock cylinders.

2.4L ........................................... 11.2 Qts. (10.6L)\
3.0L ........................................... 13.0 Qts. (12.3L)\
3.3L & 3.8L .................................... 13.2 Qts. (12.5L)\
Automatic Transaxle (Mopar ATF Plus Type 7176)
3-Speed
Drain & Refill .............................. (4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 8.5 Qts. (8.0L)\
4-Speed
Drain & Refill .............................. ( 4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 9.1 Qts. (8.6L)\
Overrunning Clutch
(Mopar ATF Plus Type 7176 - AWD Models) ...................... ( 5)
Power Steering Fluid ( 6) ............................ 1.7 Pts. (.8L)
Power Transfer Unit
(SAE 80W-90/API GL-5 - AWD Models) .............. 1.2 Qts. (1.14L\
)
Rear Differential
(SAE 80W-90/API GL-5 - AWD Models) ( 5) ....................... ( 7)
( 1) - Approximate quantity listed.
( 2) - Use an API energy conserving engine oil that is certified for
gasoline engines on all engines except 3.3L flex-fuel models.
On 3.3L flex-fuel models, use Mopar Flex-Fuel 5W-30 engine oil
or an equivalent that meets Chrysler Standard MS-9214. Proper
engine oil MUST BE used to prevent engine damage. The 3.3L
flex-fuel model may be referred to as Flex-Fuel Vehicle (FFV)
model and is used in all vehicles except California emission
vehicles. Flex-fuel model may be also referred to as an E85
application and may be identified by label attached to inside of
gasoline filler door.
( 3) - Quantity includes heater and coolant recovery tank. Add 2 qts.
(1.9L) if equipped with rear heater.
( 4) - Add this amount of fluid. Start engine and shift transaxle
through all gears and back to Park. Add additional fluid to
bring fluid level to 1/8" below the ADD mark on dipstick.
Recheck fluid level with transaxle at normal operating
temperature. Adjust fluid level so fluid level is within the
HOT range dipstick.
( 5) - An overrunning clutch is bolted on front of rear differential,
between torque tube for drive shaft and rear differential.
Overrunning clutch contains a separate reservoir from rear
differential. Ensure fluids are checked at appropriate
component, as different types of fluids are used. Fluid capacity
is not available from manufacturer.
( 6) - Use only Mopar power steering fluid. DO NOT use automatic
transmission fluid.
( 7) - Capacity is not available from manufacturer. Fill unit until
fluid level is even with bottom of filler plug hole.









\









\









\









\









\









\









\







FLUID CAPACITIES (DAKOTA)








\









\









\









\









\









\









\







Application ( 1) Quantity
Crankcase (Includes Filter) ( 2)
2.5L ............................................. 4.5 Qts. (4.3L)\
3.9L ............................................. 4.0 Qts. (3.8L)\
5.2L & 5.9L ...................................... 5.0 Qts. (4.7L)\
Cooling System (Includes Heater)
2.5L ............................................. 9.8 Qts. (9.3L)\
3.9L ........................................... 14.0 Qts. (13.2L)\
5.2L & 5.9L .................................... 14.3 Qts. (13.5L)\
Automatic Transmission
(Mopar ATF Plus Type 7176)

2.4L ............................. 170-225 psi (11.9-15.7 kg/cm)
3.0L ...................................... 178 psi (12.5 kg/cm)
3.3L ........................................................ ( 1)
Minimum Compression Pressure
Caravan, Town & Country, & Voyager .......... 100 psi (7.0 kg/cm
)
Dakota
2.5L ........................................................ ( 1)
3.9L, 5.2L & 5.9L .......................... 100 psi (7.0 kg/cm
)
Durango ..................................... 100 psi (7.0 kg/cm)
Ram Pickup
3.9L, 5.2L & 5.9L (Gasoline) & 8.0L ........ 100 psi (7.0 kg/cm
)
5.9L (Diesel) ............................................... ( 1)
Ram Van & Ram Wagon ......................... 100 psi (7.0 kg/cm
)
Maximum Variation Between Cylinders
Caravan, Town & Country & Voyager ..................... 25 Percent
Dakota
2.5L ........................................ 30 psi (2.1 kg/cm
)
3.9L, 5.2L & 5.9L ........................................... ( 1)
Durango ...................................................... ( 1)
Ram Pickup, Ram Van & Ram Wagon .............................. ( 1)
( 1) - Information is not available from manufacturer.









\









\









\









\









\









\









\







VALVE CLEARANCE
Gasoline Models
All engines are equipped with hydraulic lifters. No
adjustments are required.
5.9L Diesel (Ram Pickup)
Valve adjustment is recommended every 150 months or 150,000
miles during normal service, every 135,000 miles during severe
service. Severe service is described as frequent short trip operation
of less than 5 miles, long periods of engine idling, trailer towing,
police, taxi, local delivery service, or operating in dusty or
excessively hot conditions. See VALVE CLEARANCE SPECIFICATIONS
(DIESEL) table.
VALVE CLEARANCE SPECIFICATIONS (DIESEL) ( 1)









\









\









\









\









\









\









\







Application In. (mm)\
Intake Valve ............................................ .010 (.25)\
Exhaust Valve ........................................... .020 (.51)\
(1) - Adjust valves with engine temperature less than 140
F (60C).








\









\









\









\









\









\









\







IGNITION SYSTEM
IGNITION COIL
IGNITION COIL RESISTANCE - Ohms @ 70-80F (21-27C)








\









\









\









\









\









\









\







Application Primary Secondary
Caravan
2.4L
Diamond ( 1)( 2) ............... .53-.65 .......... 11,500-13,500
Weastec ( 1) .................. .45-.65 .......... 10,900-14,700
3.0L ............................. ( 3) ..................... ( 3)

ON-VEHICLE TESTING
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
DISABLING/ENABLING IGNITION & FUEL SYSTEMS
WARNING: To prevent engine from starting while performing tests,
always disable ignition and fuel systems.
Disabling Ignition & Fuel Systems
Remove Automatic Shutdown Relay (ASD) located in Power
Distribution Center (PDC). Refer to PDC cover for proper relay
location. PDC is located in engine compartment. On 5.9L diesel
engines, also disconnect fuel shutdown solenoid connector. Solenoid is
located behind upper intake manifold. See appropriate SYSTEM &
COMPONENT TESTING article in ENGINE PERFORMANCE section.
Enabling Ignition & Fuel Systems
When testing and/or repairs have been completed, verify
battery condition. Recharge battery as necessary, after starter tests
have been completed. Disconnect all test equipment. Install ASD relay.
On 5.9L diesel engines, reconnect fuel shutdown relay connector. On
all models, start engine several times to verify malfunction has been
corrected.
CRANKING TEST
NOTE: Ensure engine is at normal operating temperature. High
viscosity oil, extreme cold temperatures, or tight engine
will increase amperage draw.
1) Using a battery load tester, connect positive and negative
leads to battery. Connect inductive ammeter pick-up to positive
battery cable. Disable ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS.
2) Ensure all lights and accessories are off. Place A/T in
Park position or M/T in Neutral position. Apply parking brake. Crank
engine and observe voltmeter reading. If voltage is more than 9.6
volts and cranking amperage draw is more than specified amps, proceed
to CIRCUIT RESISTANCE TESTS. See STARTER SPECIFICATIONS - CARS or
STARTER SPECIFICATIONS - TRUCKS.
3) If voltage is 12.5 volts or more and cranking amperage
draw is less than specified, check starter circuit components in the
following order:
starter solenoid, starter relay, starter relay circuit, park/neutral
position switch or transmission range sensor (A/T), clutch pedal
position switch (M/T), ignition switch, wiring harness and
connections.
CIRCUIT RESISTANCE TESTS
NOTE: If excessive resistance is not found in circuits being
tested, remove starter and proceed to BENCH TESTING.
Battery Connection Resistance Test
1) Disable vehicle ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS. A voltmeter accurate to
one tenth of a volt will be needed for the following tests.