1999 DODGE RAM tire size

Refrigerant R-12 based systems use mineral oil, while R-134a
systems use synthetic Polyalkylene Glycol (PAG) oils. Using a mineral
oil based lubricant with R-134a will result in A/C compressor failure
due to lack of proper lubrication.
Following are the most common R-134a refrigerant oils used by
most domestic vehicles:
Chrysler Corp., Eagle & Jeep
Use ND-8 PAG oil, SUN PAG 56 oil, SP-10 PAG Oil, or SP-20 PAG
oil.
Ford Motor Co.
Use YN-12B or YN-12C PAG Refrigerant Oil (specification WSH-
M1C231-B) or SP-20 PAG Oil (specification WST-M1C231-B2).
General Motors
On all models except Saturn, use PAG Refrigerant Oil (Part
No. 12345923). On Saturn, use Saturn PAG refrigerant oil.
NOTE: PAG oil absorbs moisture very rapidly, 2.3-5.6 percent by
weight as compared to a mineral oil absorption rate of .005
percent by weight.
NOTE: Use ONLY the specified oil for the appropriate system or A/C
compressor. Always check the underhood A/C specification
label or A/C compressor label before adding refrigerant oil
to A/C system.
SYSTEM SERVICE VALVES
SCHRADER-TYPE VALVES
NOTE: Although similar in construction and operation to a tire
valve, NEVER replace a Schrader-type valve with a tire
valve.
Schrader valve is similar in construction and operation to a
tire valve. See Fig. 4. When a test gauge hose is attached (hose has
built-in valve core depressor), Schrader stem is pushed inward to the
open position and allows system pressure to reach the gauge.
If test hose being used does not have a built-in core
depressor, an adapter must be used. Never attach hoses or adapters to
a Schrader valve unless it is first connected to manifold gauge set.
Fig. 4: Schrader Service Valve (Compressor Location Shown)
SPECIAL VALVE CONNECTORS
On some General Motors models, thread size on high-side

AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).

Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding, affecting
performance ............ A .. Require repair or replacement.
Binding, not affecting
performance ............ 2 .. Suggest repair or replacement.
Broken .................. A .. Require repair or replacement.
Burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Burned, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Float saturated ......... A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... ( 2) Require repair or
replacement.
Melted, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Melted, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Missing ................. C ............ Require replacement.
Out of adjustment ....... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Won't return ............ A .. Require repair or replacement.
Worn .................... 1 ............ Suggest replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Includes inoperative, intermittent operation, or failure to
perform all functions.









\









\









\









\









\









\









\


TIRES
Consult the vehicle owner's manual or vehicle placard for
correct size, speed ratings, and inflation pressure of the original
tires.
TIRE INSPECTION

\









\









\









\









\









\









\


Condition Code Procedure
Tire diameter incorrect,
affecting ABS or TCS ... A ............ Require replacement.
Tire pressure incorrect,
affecting ABS or TCS ... A .. Require repair or replacement.
Tire size incorrect,
affecting ABS or TCS ... A ............ Require replacement.









\









\









\









\









\









\









\


TOOTHED RINGS (TONE WHEEL)
NOTE: Copied from Drivetrain UIGs.
If the toothed ring requires replacement and cannot be
replaced as a separate component, replace the assembly of which the
ring is a part.
TOOTHED RING INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Alignment incorrect ..... B ............... Require repair or
replacement.
Bent .................... B ............ Require replacement.
Contaminated, affecting
performance ............. A ........ Require repair. Identify
and correct cause.
Cracked ................. B ............ Require replacement.
Loose ................... A ............. Require replacement
of worn parts.
Missing ................. C ............ Require replacement.
Number of teeth
incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.









\









\









\









\









\









\









\


VACUUM BOOSTERS
VACUUM BOOSTER INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Applies too much assist
(oversensitive) ........ A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Auxiliary vacuum pump
inoperative ............ A ........... ( 1) Require repair or
replacement.
Check valve grommet
deteriorated, affecting
performance ............ A .. Require replacement of grommet.

Diagnostic Readout Box III (DRB-III) scan tool to Data Link Connector
(DLC) below driver's side of instrument panel. For DLC location, see
appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
2) Select SPECIAL FUNCTION on scan tool. Set scan tool to
QUICK LEARN mode. Follow scan tool manufacturer's instructions to
perform transaxle shift quality quick learn procedure. Remove scan
tool.
Pinion Factor Procedure (All FWD Cars Except Avenger &
Sebring Coupe, & All FWD Vans)
1) Electronic pinion factor procedure must be performed to
provide proper speedometer operation if Transmission Control Module
(TCM) is replaced. If pinion factor procedure is not performed,
improper speedometer readings may exist or speedometer may not
operate. Pinion factor procedure must be performed using Chrysler's
Diagnostic Readout Box (DRB-III) scan tool.
2) Connect scan tool to Data Link Connector (DLC) below
driver's side of instrument panel. For DLC location, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
3) Select TRANSMISSION system, MISCELLANEOUS functions, then
PINION FACTOR. Scan tool will now display tire size. If tire size is
incorrect, press ENTER key and select correct size. Press PAGE BACK
key to exit procedure.
Pinion Factor Procedure (Avenger & Sebring Coupe)
1) Transaxle uses rotation speed of output shaft to calculate
vehicle speed and cumulative distance travelled. Therefore, it is
necessary to input or update tire size into TCM memory after TCM has
been replaced or tire size has been changed.
2) Select SPECIAL FUNCTION on Chrysler's Diagnostic Readout
Box (DRB-III) scan tool. Set scan tool to PINION FACTOR mode. Input
tire size into TCM memory.
NOTE: New TCMs do not have tire size input into memory. TCM may
also be referred to as EATX module.

Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.

Fig. 6: Measuring Valve Stem-to-Guide Clearance - Typical
This Graphic For General Information Only
Lower valve approximately 1/16" below valve seat. Push valve
stem against valve guide as far as possible. Adjust dial indicator to
zero. Push valve stem in opposite direction and note reading.
Clearance must be within specification.
If valve guide clearance exceeds specification, valves with
oversize stems may be used or valve guide must be replaced. On some
applications, a false guide is installed, then reamed to proper
specification. Valve guide reamer set is used to ream valve guide to
obtain proper clearance for new valve.
Reaming Valve Guide
Select proper reamer for valve stem. Reamer must be of
proper length to provide clean cut through entire length of valve
guide. Install reamer in valve guide and rotate to cut valve guide.
See Fig. 7 .

the old insert and machining an oversize insert bore. Replacement
oversize insert is usually chilled and the cylinder head is sometimes
warmed. Valve seat is pressed into the head. This operation requires
specialized machine shop equipment.
Valve Seat Concentricity
Using dial gauge, install gauge pilot in valve guide.
Position gauge arm on the valve seat. Adjust dial indicator to zero.
Rotate arm 360 degrees and note reading. Runout should not exceed
specification.
To check valve-to-valve seat concentricity, coat valve face
lightly with Prussian Blue dye. Install valve and rotate it on valve
seat. If pattern is even and entire seat is coated at valve contact
point, valve is concentric with the seat.
REASSEMBLY
Valve Stem Installed Height
Valve stem installed height must be checked when new valves
are installed or when valves or valve seats have been ground. Install
valve in valve guide. Measure distance from tip of valve stem to
spring seat. See Fig. 11. Distance must be within specifications.
Fig. 11: Measuring Valve Stem Installed Height - Typical
This Graphic For General Information Only
Remove valve and grind valve stem tip if height exceeds
specification. Valve tips are surface hardened. DO NOT remove more