4-1
EAU01114
PRE-OPERATION CHECKS
1
2
3
4
5
6
7
8
9Owners are personally responsible for their vehicle’s condition. Your motorcycle’s vital functions can start to
deteriorate quickly and unexpectedly, even if it remains unused (for instance, if it is exposed to the elements).
Any damage, fluid leak or loss of tire pressure could have serious consequences. Therefore, it is very important
that, in addition to a thorough visual inspection, you check the following points before each ride.
EAU00340PRE-OPERATION CHECK LIST
ITEM CHECKS PAGE
Brakes9Check operation, condition and free play.
3-5, 6-18 ~ 6-21
9Adjust if necessary.
Clutch9Check operation and free play.
3-4, 6-18
9Adjust if necessary.
9Check for smooth operation.
Throttle grip and housing9Lubricate.6-14, 6-24
9Adjust throttle cable free play if necessary.
Engine oil9Check oil level.
6-8 ~ 6-11
9Fill with oil if necessary.
Drive chain9Check chain slack and condition.
6-21 ~ 6-23
9Adjust if necessary.
Wheels and tires9Check tire pressure, wear, damage and spoke tightness.
6-15 ~ 6-17
9Tighten spokes if necessary.
Brake and shift pedal shafts9Check for smooth operation.
6-24
9Lubricate if necessary.
Brake and clutch lever pivots9Check for smooth operation.
6-25
9Lubricate if necessary.
Sidestand pivot9Check for smooth operation.
6-25
9Lubricate if necessary.
Chassis fasteners9Make sure that all nuts, bolts, and screws are properly tightened.
—
9Tighten if necessary.
5FY-28199-EX (TW200) 4/16/02 5:38 PM Page 22
7-1
EAU01010
CLEANING AND STORAGE
1
2
3
4
5
6
7
8
9
EAU01301A. CLEANING
Frequent, thorough cleaning of
your motorcycle will not only
enhance its appearance but will
improve its
general performance and extend
the useful life of many compo-
nents.
ECA00002
cC
8Improper cleaning can damage
the cowlings, panels and other
plastic parts. Use only a soft,
clean cloth or sponge with
mild detergent and water to
clean plastic.
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
EC000111
cC
Excessive hose pressure may
cause water seepage and deterio-
ration of wheel bearings, front
fork, brakes, transmission seals
and electrical parts.
Many expensive repair bills have
resulted from improper high pres-
sure detergent applications such
as those available in coin-operated
car washers.
4. After riding on salted roads,
wash the motorcycle with cold
water immediately. Do not use
warm water as it increases the
chemical reaction of the salt.
5. Once the majority of the dirt
has been hosed off, wash all
surfaces with warm water and
mild, detergent-type soap. An
old toothbrush or bottle brush
is handy for hard-to-get-at
places. 1. Before cleaning the motorcy-
cle:
a. Block off the end of the
exhaust pipe to prevent water
entry; a plastic bag and strong
rubber band may be used.
b. Make sure the spark plug and
all filler caps are properly
installed.
2. If the engine case is excessive-
ly greasy, apply degreaser
with a paint brush. Do not
apply degreaser to the chain,
sprockets or wheel axles.
3. Rinse the dirt and degreaser
off with a garden hose. Use
only enough pressure to do
the job.
5FY-28199-EX (TW200) 4/16/02 5:38 PM Page 65
