1998 TOYOTA T100 light

T100(U)
2
Instrument panel overview
1. Side vent
2. Instrument cluster
3. Center vents
4. Personal lights
5. Glovebox
6. Power door lock switch
7. Power window switches
8. Manual transmission gear shift lever
9. Front drive control lever
10. Lower vent
11. Hood lock release lever
12. Power rear view mirror control switch

T100(U)3
1. Clutch start cancel switch
2. Headlight and turn signal switch
3. Windshield wiper and washer switches
4. Automatic transmission selector lever
5. Emergency flasher switch
6. Clock
7. Cup holder
8. Air conditioning controls
9. Car audio
10. Ashtray
11. Cigarette lighter
12. Parking brake lever
13. Ignition switch
14. Cruise control switch
15. Tilt steering lock release lever
16. Instrument panel light control knob

T100(U)
4
1. Engine coolant temperature gauge
2. Service reminder indicators or indicator lights
3. Trip meter 4. Odometer
5. Speedometer
6. Fuel gauge
7. Trip meter reset knob
Instrument cluster overview
Without tachometer

T100(U)5
1. Engine coolant temperature gauge
2. Oil pressure gauge
3. Tachometer
4. Service reminder indicators or indicatorlights 5. Odometer
6. Speedometer
7. Trip meter
8. Voltmeter
9. Low fuel level warning light
10. Fuel gauge 11. Trip meter reset knob

With tachometer

T100(U)
6
Indicator symbols on the instrument panel
Automatic transmission fluid temparature warning
light

SRS airbag warning light
Unengaged ”Park” warning light
Anti-lock brake system warning light
Seat belt reminder light

(type A)
(type B)
Low oil pressure warnig light

Low fuel level warning light
Brake system warning light

Discharge warning light
Malfunction indicator lamp
Low windshield washer fluid level warning light
Headlight high beam indicator light
Overdrive-off indicator light
Turn signal indicator lights
”4WD” indicator light
Automatic transmission indicator lights
Cruise control indicator light
The indicators marked with
are service reminder indicators.
For details, see ”Service reminder indicators and warning buzze rs”
in Chapter 1 −5.

T100(U)9
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the ve-
hicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the ve-
hicle during an accident. It also helps
prevent the doors from being opened
unintentionally.
Power windows
The windows can be operated with the
switch on each door.
The power windows work when the ignition
switch is in the ”ON” position. However,
if both doors are closed, they work for 60
seconds after the ignition is turned off.
They stop working when either door is opened.
OPERATING THE DRIVER’S WINDOW
Use the switch on the driver’s door.
Normal operation: The window moves as
long as you hold the switch.
To open: Lightly push down the switch.
To close: Pull up the switch.Automatic operation (to open only):
Push the switch completely down and then
release it. The window will fully open. To
stop the window partway, lightly pull the
switch up and then release it.

T100(U)
12
REMOVAL 1. Open the tailgate to the angle where you can release the support brackets
from the lugs on both sides.
2. Open the tailgate to about 30 ° from
vertical and pull up the right side of
the tailgate to unhook the right side.
3. Slide the tailgate a little to the right to unhook the left side.
To install the tailgate, follow the removal
procedure in reverse order.
After closing the tailgate, try pulling it to-
ward you to make sure it is securely
closed.
We recommend you keep the tailgate
closed when not in use.
NOTICE
Before unhooking the tailgate, fold
the support brackets.
Make sure the support brackets are
securely latched on both side pan-
els when installing the tailgate.
Hood
To open the hood, do the following.
1. Pull the hood lock release lever. The hood will spring up slightly.
CAUTION
Before driving, be sure that the hood
is closed and securely locked. Other-
wise, the hood may open unexpected-
ly while driving and an accident may
occur.

T100(U)
14
Do not fill a fuel container on a
plastic truck bed liner, a rubber
truck bed mat, or any other insulat-
ing material. A static electricity
charge could cause a spark and fire
hazard. The proper procedure is to
place an approved fuel container on
the ground away from the truck for
filling.
2. To remove the fuel tank cap, turn
the cap slowly counterclockwise,
then pause slightly before removing
it. After removing the cap, hang it
on the cap hanger.
It is not unusual to hear a slight swoosh
when the cap is opened. When installing,
turn the cap clockwise till you hear a click.
If the cap is not tightened securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely. The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.
CAUTION

Make sure the cap is tightened se-
curely to prevent fuel spillage in
case of an accident.
Use only a genuine Toyota fuel tank
cap for replacement. It has a built-
in check valve to reduce fuel tank
vacuum.