1998 TOYOTA LAND CRUISER Electrical connectors

I25542
I25539
Connector ºAº
Connector ºBº
Connector ºCº BE-172
- BODY ELECTRICALAUDIO SYSTEM
2545 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. INSPECT DVD CHANGER CIRCUIT
Disconnect the connector from DVD changer and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
20 - GroundConstantContinuity
1 - GroundIgnition switch LOCKNo voltage
1 - GroundIgnition switch ACC or ONBattery voltage
10 - GroundConstantBattery voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
4. INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly,
and inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
A20 - GroundConstantContinuity
A1 - GroundConstantBattery voltage
A11 - GroundIgnition switch LOCKNo voltage
A11 - GroundIgnition switch ACC or ONBattery voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I24857EAU AU1AU2
- BODY ELECTRICALAUDIO SYSTEM
BE-173
2546 Author
: Date
:
2004 LAND CRUISER (RM1071U)
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.
5. INSPECT STEERING PAD SWITCH CIRCUIT
Disconnect the connectors from the steering pad switch, and in-
spect the connector on the wire harness side.
Tester connectionConditionSpecified condition
AU1 - EAUDo not switch positionApprox. 100 kW
AU1 - EAUSEEK+ switch: push0 W
AU1 - EAUSEEK- switch: pushApprox. 0.3 W
AU1 - EAUVOL+ switch: pushApprox. 1k W
AU1 - EAUVOL- switch: pushApprox. 3.2 kW
AU2 - EAUDo not switch positionApprox. 100 kW
AU2 - EAUMODE switch: push0 W
If the circuit is not as specified, inspect the circuits connected
to other parts.

BE-150
- BODY ELECTRICALAUDIO SYSTEM
2523 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4. PROBLEM SYSMPTOMS TABLE
NOTICE:
When replacing the internal mechanism (computer part) of the audio system, be careful that no part
of your body or clothing comes in contact with the terminals of the leads from the IC, etc. of the re-
placement part (spare part).
HINT:
This inspection procedure is a simple troubleshooting which should be carried out on the vehicle during sys-
tem operation and was prepared on the assumption of system component troubles (except for the wires and
connectors, etc.).
Always inspect the trouble taking the following items into consideration.
Open or short circuit of the wire harness
Connector or terminal connection fault
ProblemFlow chart No.
RadioRadio not operating when power switch turned to 'ON'.1
Display indicates when power switch turned to 'ON', but no sound (including
'noise') is produced.2
Noise present, but AM - FM not operating.3
Any speaker does not work.4
Any AM or FM does not work.5
Few preset turning bands.5
Reception poor.6
Sound quality poor.7
Preset memory disappears.8
Tape PlayerCassette tape cannot be inserted.9
Cassette tape inserted, but no power.10
Power coming in, but tape player not operating.11
Any speaker does not work.12
Sound quality poor.13
Tape jammed, malfunction with tape speed or auto-reverse.14
Cassette tape will not eject.15
CD PlayerCD cannot be inserted.16
CD inserted but no power/17
Power coming in, but CD player not operating.18
Sound jumps.19
Sound quality poor (Volume faint)20
Any speaker does not work.21
CD will not be ejected.22
Power AmplifierNo power coming in.23
Power coming in, but power amplifier not operating.24
Any speaker does not work.25
NoiseNoise occurs26
Noise produced by vibration or shock while driving.27
Noise produced when engine starts.28
Steering Pad SwitchA audio system cannot be operated with steering pad switch.29
Rear Seat AudioQuality of sound from headphone connected to headphone terminal is poor or no
sound can be heard.30

BE2EF-01
1
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 1120
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
11
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 11
20
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
1
I29077
Connector C15 Connector C14 Connector C13 Connector C12
- BODY ELECTRICALCOMBINATION METER
BE-63
2436 Author
: Date
:
INSPECTION
1. INSPECT COMBINATION METER CIRCUIT
Connect the connector C12, C13, C14 and C15 to the combina-
tion meter and inspect the wire harness side connectors from
the back side as shown in the table.
Tester connectionConditionSpecified condition
C12 3 (DOOR ) G dEither door is openedBelow 1 VC12-3 (DOOR-) - GroundEither door is closed10 - 14 V
C12 4 (TURN L) G d
Ignition switch ON and
turn signal switch OFF or RIGHTBelow 1 V
C12-4 (TURN-L) - GroundIgnition switch ON and
turn signal switch LEFTPulse signal is output
10 - 14 V eBelow 1 V
C12 5 (BEAM ) G dIG switch ON, light control switch OFFBelow 1 VC12-5 (BEAM+) - GroundIG switch ON, light control switch ON10 - 14 V
C12 6 (TURN R) G d
Ignition switch ON and
turn signal switch OFF or LEFTBelow 1 V
C12-6 (TURN-R) - GroundIgnition switch ON and
turn signal switch RIGHTPulse signal is output
10 - 14 V eBelow 1 V
C12-7 (BEAM-) - GroundIG switch ON, light control switch ONBelow 1 V
C12 10 (CHG ) G dIgnition switch OFFBelow 1 VC12-10 (CHG+) - GroundIgnition switch ON10 - 14 V
C12 12 (ABS) G d
Ignition switch ON and ABS warning light lights
upBelow 1 V
C12-12 (ABS) - GroundIgnition switch ON and
ABS warning light does not light up10 - 14 V
C13 8 (ILL ) G dIG switch OFFBelow 1 VC13-8 (ILL+) - GroundIG switch ON10 - 14 V

- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-805
998 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DTC B1135/24 Half Connection in Airbag Sensor Assembly
Connector
CIRCUIT DESCRIPTION
The airbag sensor assembly detects partial connection of connector.
For details of the function of each component, see OPERATION on page RS-3.
DTC B1135/24 is recorded when the airbag sensor assembly detects an open in the electrical connection
check mechanism of the airbag sensor connector or in the airbag sensor circuit.
DTC No.DTC Detecting ConditionTrouble Area
B1135/24

Malfunction of electrical connection check mechanism of
airbag sensor assembly connector

Airbag sensor assembly malfunction
Electrical connection check mechanism

Airbag sensor assembly
INSPECTION PROCEDURE
1 Are connectors of airbag sensor assembly properly connected?
NO Connect connectors.
YES
2 Prepare for inspection (See step 1 on page DI-923).
DIB3S-01

2003
All rights reserved. This book may not be
reproduced or copied, in whole or in part, without
the written permission of Toyota Motor
Corporation.
2004 LAND CRUISER (EWD548U)
1
2004 LAND CRUISER
ELECTRICAL WIRING DIAGRAM
Section Code Page
INTRODUCTION A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
HOW TO USE THIS MANUAL B. . . . . . . . . . . . . . . . . .
3
TROUBLESHOOTING C. . . . . . . . . . . . . . . . . . . . . . . . .
12
ABBREVIATIONS D. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
GLOSSARY OF TERMS AND SYMBOLS E. . . . . . . .
18
RELAY LOCATIONS F. . . . . . . . . . . . . . . . . . . . . . . . . . .
20
ELECTRICAL WIRING ROUTING G. . . . . . . . . . . . . . .
68
SYSTEM CIRCUITS H. . . . . . . . . . . . . . . . . . . . . . . . . . .
93
GROUND POINT I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
376
POWER SOURCE (Current Flow Chart) J. . . . . . . . .
384
CONNECTOR LIST K. . . . . . . . . . . . . . . . . . . . . . . . . . . .
394
PART NUMBER OF CONNECTORS L. . . . . . . . . . . . .
406
OVERALL ELECTRICAL WIRING DIAGRAM M. . . . .
410

2004 LAND CRUISER (EWD548U)
2A INTRODUCTION
This manual consists of the following 13 sections:
No.
SectionDescription
A
INDEXIndex of the contents of this manual.
A
INTRODUCTIONBrief explanation of each section.
BHOW TO USE THIS
MANUALInstructions on how to use this manual.
CTROUBLE-
SHOOTINGDescribes the basic inspection procedures for electrical circuits.
DABBREVIATIONSDefines the abbreviations used in this manual.
E
GLOSSARY OF
TERMS AND
SYMBOLS
Defines the symbols and functions of major parts.
FRELAY LOCATIONSShows position of the Electronic Control Unit, Relays, Relay Block, etc.
This section is closely related to the system circuit.
GELECTRICAL
WIRING ROUTINGDescribes position of Parts Connectors, Splice points, Ground points, etc.
This section is closely related to the system circuit.
INDEXIndex of the system circuits.
H
SYSTEM CIRCUITS
Electrical circuits of each system are shown from the power supply through ground
points. Wiring connections and their positions are shown and classified by code
according to the connection method. (Refer to the section, ºHow to use this manualº).
The ºSystem Outlineº and ºService Hintsº useful for troubleshooting are also contained
in this section.
IGROUND POINTShows ground positions of all parts described in this manual.
JPOWER SOURCE
(Current Flow Chart)Describes power distribution from the power supply to various electrical loads.
KCONNECTOR LISTDescribes the form of the connectors for the parts appeared in this book.
This section is closely related to the system circuit.
LPART NUMBER OF
CONNECTORSIndicates the part number of the connectors used in this manual.
M
OVERALL
ELECTRICAL
WIRING DIAGRAM
Provides circuit diagrams showing the circuit connections.

2004 LAND CRUISER (EWD548U)
3 HOW TO USE THIS MANUAL B
This manual provides information on the electrical circuits installed on vehicles by
dividing them into a circuit for each system.
The actual wiring of each system circuit is shown from the point where the power
source is received from the battery as far as each ground point. (All circuit
diagrams are shown with the switches in the OFF position.)
When troubleshooting any problem, first understand the operation of the circuit
where the problem was detected (see System Circuit section), the power source
supplying power to that circuit (see Power Source section), and the ground points
(see Ground Point section). See the System Outline to understand the circuit
operation.
When the circuit operation is understood, begin troubleshooting of the problem
circuit to isolate the cause. Use Relay Location and Electrical Wiring Routing
sections to find each part, junction block and wiring harness connectors, wiring
harness and wiring harness connectors, splice points, and ground points of each
system circuit. Internal wiring for each junction block is also provided for better
understanding of connection within a junction block.
Wiring related to each system is indicated in each system circuit by arrows
(from__, to__). When overall connections are required, see the Overall Electrical
Wiring Diagram at the end of this manual.