Page 2723 of 3115
RS0BF-06
H21418
H18916
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
RS-31
2306 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
Never use the airbag parts from another vehicle.
When replacing parts, replace them with new parts.
1. DISCONNECT AIRBAG CONNECTOR
(a) Remove the glove compartment door.
(b) Remove the No. 1 under cover from the lower No. 2 finish
panel.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Pull up the connector.
(d) Disconnect the front passenger airbag connector.
2. REMOVE INSTRUMENT PANEL
(See page BO-84)
3. REMOVE CENTER BRACKET
4. REMOVE DEFROSTER NOZZLE ASSEMBLY
5. REMOVE NO. 5 HEATER TO REGISTER DUCT
6. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
7. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
Remove the 3 nuts, then remove the front passenger airbag as-
sembly.
CAUTION:
Do not store the front passenger airbag assembly
with the airbag deployment side facing downward.
Never disassemble the front passenger airbag as-
sembly.
Page 2737 of 3115
RS0VL-01
H21589
H03731
A
B
H03732
H03733
RS-44
- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
2319 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
Never use the airbag parts from another vehicle.
When replacing parts, replace them with new parts.
1. REMOVE FRONT SEAT
(a) Remove the 4 seat track covers and 4 bolts.
(b) Disconnect the power seat and side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Remove the front seat.
NOTICE:
Be careful not to damage the body.
2. REMOVE HEADREST
3. REMOVE SEATBACK BOARD
Remove the seatback board as shown in the illustration.
HINT:
Remove the seatback board in order ºAº and ºBº as shown in
the illustration.
4. REMOVE SEAT CUSHION OUTER SHIELD
(a) Remove the 4 screws.
(b) Disconnect the connectors as shown in the illustration.
(c) Remove the seat cushion outer shield.
Page 2743 of 3115
RS0NM-08
H20946
- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS-83
2358 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the side and curtain shield airbag sensor
assembly involved in a collision when the airbag has
deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 9, refer to page BO-101.
1. INSTALL SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR
(a) Install the side and curtain shield airbag sensor assembly
with the 2 bolts.
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
(b) Connect the connector of the side and curtain shield air-
bag sensor assembly.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT
Torque:
Upper bolt: 8.0 N´m (81 kgf´cm, 71 in.´lbf)
3. INSTALL CENTER PILLAR LOWER GARNISH
4. INSTALL REAR DOOR OPENING TRIM WEATH-
ERSTRIP
5. INSTALL FRONT DOOR OPENING TRIM WEATH-
ERSTRIP
Page 2745 of 3115
RS0NJ-08
H20946
RS-80- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
2355 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
Do not open the cover or the case of the ECU and vari-
ous electrical devices unless absolutely necessary
(If the IC terminals are touched, the IC may be de-
stroyed by static electricity.).
HINT:
For step 1 to 8, refer to page BO-97.
1. REMOVE REAR DOOR SCUFF PLATE
2. REMOVE FRONT DOOR SCUFF PLATE
3. REMOVE LAP BELT OUTER ANCHOR COVER
4. REMOVE FRONT SEAT OUTER BELT FLOOR AN-
CHOR
5. REMOVE FRONT DOOR OPENING TRIM WEATH-
ERSTRIP
6. REMOVE REAR DOOR OPENING TRIM WEATH-
ERSTRIP
7. REMOVE CENTER PILLAR LOWER GARNISH
8. REMOVE FRONT SEAT OUTER BELT
9. REMOVE SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Disconnect the connector with the sensor assembly
installed.
(b) Remove the 2 bolts and side and curtain shield airbag
sensor assembly.
Page 2749 of 3115
RS0VQ-01
H20950
RS-94
- SUPPLEMENTAL RESTRAINT SYSTEMSEAT POSITION SENSOR ASSEMBLY
2369 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the seat position sensor assembly in-
volved in a collision when the airbag has deployed.
Never repair a sensor in order to reuse it.
1. INSTALL SEAT POSITION SENSOR ASSEMBLY
(a) Connect the connector.
(b) Install the seat position sensor assembly with a new bolt.
Part No.:
Bolt: 90119-06871
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT ASSEMBLY (DRIVER SIDE)
(See page BO-1 17)
3. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2750 of 3115
RS0VP-01
H20950
- SUPPLEMENTAL RESTRAINT SYSTEMSEAT POSITION SENSOR ASSEMBLY
RS-91
2366 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and vari-
ous electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be de-
stroyed by static electricity.)
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
1. REMOVE FRONT SEAT ASSEMBLY (DRIVER SIDE)
(See page BO-105)
2. REMOVE SEAT POSITION SENSOR ASSEMBLY
(a) Remove the bolt and seat position sensor assembly.
(b) Disconnect the connector.
Page 2754 of 3115
RS0NM-08
H20946
- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS-83
2358 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the side and curtain shield airbag sensor
assembly involved in a collision when the airbag has
deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 9, refer to page BO-101.
1. INSTALL SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR
(a) Install the side and curtain shield airbag sensor assembly
with the 2 bolts.
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
(b) Connect the connector of the side and curtain shield air-
bag sensor assembly.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT
Torque:
Upper bolt: 8.0 N´m (81 kgf´cm, 71 in.´lbf)
3. INSTALL CENTER PILLAR LOWER GARNISH
4. INSTALL REAR DOOR OPENING TRIM WEATH-
ERSTRIP
5. INSTALL FRONT DOOR OPENING TRIM WEATH-
ERSTRIP
Page 2756 of 3115
RS0NJ-08
H20946
RS-80- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
2355 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
Do not open the cover or the case of the ECU and vari-
ous electrical devices unless absolutely necessary
(If the IC terminals are touched, the IC may be de-
stroyed by static electricity.).
HINT:
For step 1 to 8, refer to page BO-97.
1. REMOVE REAR DOOR SCUFF PLATE
2. REMOVE FRONT DOOR SCUFF PLATE
3. REMOVE LAP BELT OUTER ANCHOR COVER
4. REMOVE FRONT SEAT OUTER BELT FLOOR AN-
CHOR
5. REMOVE FRONT DOOR OPENING TRIM WEATH-
ERSTRIP
6. REMOVE REAR DOOR OPENING TRIM WEATH-
ERSTRIP
7. REMOVE CENTER PILLAR LOWER GARNISH
8. REMOVE FRONT SEAT OUTER BELT
9. REMOVE SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Disconnect the connector with the sensor assembly
installed.
(b) Remove the 2 bolts and side and curtain shield airbag
sensor assembly.
