1998 TOYOTA 4RUNNER brake

4RUNNER (1998)
If the preset speed automatically can-
cels out other than for the above
cases, have your vehicle checked by
your Toyota dealer at the earliest op-
portunity.
RESETTING AT A FASTER SPEED
Push the lever up in the ºRES/ACCº
direction and hold it. Release the le-
ver when the desired speed is at-
tained. While the lever is held up, the
vehicle will gradually gain speed.
However, a faster way to reset is to
accelerate the vehicle and then push
the lever down in the ºSET/COASTº
direction.
RESETTING AT A SLOWER SPEED
Push the lever down in the ºSET/
COASTº direction and hold it. Release
the lever when the desired speed is
attained. While the lever is held down,
the vehicle speed will gradually de-
crease.
However, a faster way to reset is to
depress the brake pedal and then
push the lever down in the ºSET/
COASTº direction. On vehicles with automatic transmis-
sion, even if you turn off the overdrive
switch, with the cruise control on, en-
gine braking will not be applied be-
cause the cruise control is not can-
celled. To decrease the vehicle speed,
reset to a slower speed with the
cruise control lever or depress the
brake pedal. If you use the brake ped-
al, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by
pulling the control lever or by de-
pressing the brake pedal or clutch
pedal, pushing the lever up in the
ºRES/ACCº direction will restore the
speed set prior to cancellation.
However, once the vehicle speed falls
below about 40 km/h (25 mph), the
preset speed will not be resumed.
CRUISE CONTROL FAILURE WARN-
ING
If the ºCRUISEº indicator light in the
instrument cluster flashes when using
the cruise control, press the ºCRUISE
ON- OFFº button to turn the system
off and then press it again to turn it on.If any of the following conditions then
occurs, there is some trouble in the
cruise control system.
The indicator light does not comeon.
The indicator light flashes again.
The indicator light goes out after it
comes on.
If this is the case, contact your Toyo-
ta dealer and have your vehicle in-
spected.

4RUNNER (1998)
Part 2
INFORMATION
BEFORE DRIVING
YOUR TOYOTA
Off- road vehicle precautions
Break- in period
Fuel
Operation in foreign countries
Three- way catalytic converter
Engine exhaust cautions
Facts about engine oil
consumption
Twin ground electrode spark plugs
Brake system
Brake pad wear limit
indicators
Luggage stowage precautions
Your Toyota's identification
Theft prevention labels
Suspension and chassis
Types of tires
InformationOff- road vehicle precaution

4RUNNER (1998)
Your engine is fitted with twin
ground electrode spark plugs.
NOTICE
Use only twin ground electrode
spark plugs for your engine per-formance.
Brake system
TANDEM MASTER CYLINDER
BRAKE SYSTEM
The tandem master cylinder brake
system is a hydraulic system with two
separate sub- systems. If either sub-
system s hould fail, the other will still
work. However, the pedal will be hard-
er to press, and your stopping dis-
tance will be longer. Also, the brake
system warning light may come on.
CAUTION
Do not drive your vehicle with
only a single brake system. Have
your brakes fixed immediately.
BRAKE BOOSTER The brake booster uses engine vacu-
um to power- assist the brakes. If the
engine should quit while you are driv-
ing, you can bring the vehicle to a
stop with normal pedal pressure.
There is enough reserve vacuum for
one or two stopsÐbut no more!
CAUTION

Do not pump the brake pedal if
the engine stalls. Each push on
the pedal uses up your vacuum
reserve.

4RUNNER (1998)
Even if the power assist is
completely lost, the brakes will
still work. But you will have to
push the pedal hardÐmuch
harder than normal. And your
braking distance will be longer.
ANTI- LOCK BRAKE SYSTEM
(with ºABSº warning light)
The anti- lock brake system is de-
signed to automatically help prevent
lock- up of the wheels during sudden
braking or braking on slippery road
surfaces. This assists in providing
directional stab ility and steering per-
formance of the vehicle under these
circumstances.
The anti- lock brake system becomes
operative after the vehicle has accel-
erated to a speed in excess of
approximately 10 km/h (6 mph). It
stops operating when the vehicle de-
celerates to a speed below approxi-
mately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when
the engine is started or just after the
vehicle is started. This means that the
anti- lock brake system is in the self
check mode, and does not indicate a
malfunction. Effective way to press the ºABSº
brake pedal: When the anti- lock brake
system function is in action, you may
feel the brake pedal pulsating and
hear a noise. In this situation, to let
the anti- lock brake system work for
you, just hold the brake pedal down
more firmly. Do not pump the brake.
This will result in reduced braking per-
formance.
The brake pedal pulsation caused by
the anti- lock brake system may indi-
cate hazardous road surface condi-
tions. Although the anti- lock brake
system assists in providing vehicle
control, it is still important to drive
with all due care, because the anti-
lock brake system cannot overcome
the laws of physics that act on your
vehicle:
Braking capab ility is dependent on
tire friction with the road surface.
Even though the anti- lock brake
system is operating, a driver can-
not maintain full control on certain
slippery road surfaces, when cor-
nering at high speeds, or in violent
maneuvers.
Avoid high speeds on wet roads.
The anti- lock brake system cannot
eliminate the risk of hydroplaning
and loss of tire friction. Always maintain a safe distance from
the vehicle in front of you. Compared
with vehicles not fitted with an anti-
lock brake system, your vehicle may
require a longer stopping distance in
the following cases:
Driving on rough, gravel or snow-
covered roads.
Driving with tire chains installed.
Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.
CAUTION
Do not use tires other than the
manufacturer 's designated tires,
and do not mix tires or wheels of
different sizes. You may prevent
the antilock brake system from
operating at full effectiveness.
Vehicles with rear differential lock sys-
tem 'The anti- lock brake system does
not operate when the rear differential
is locked. It is normal operation for
the ºABSº warning light to be on at
this time.

4RUNNER (1998)
When the light is on with the rear
differential locked, it indicates the
anti- lock brake system will not oper-
ate.
If either of the following conditions
occurs, this indicates a malfunction
somewhere in the parts monitored by
the warning light system. Contact your
Toyota dealer as soon as possible to
service the vehicle.
The light does not come on as
described above, or remains on.
The light comes on while driving
with the rear differential unlocked.
The light does not come on with
the rear differential locked.
The light comes on while driving. Even if the anti- lock brake system
should fail, the brake system will still
operate conventionally. However, when
the ºABSº warning light is on (and the
brake system warning light is off), the
anti- lock brake system is not assist-
ing brake performance so that the
wheels can lock- up during sudden
braking or braking on slippery road
surfaces. Have your vehicle checked
by your Toyota dealer as soon as
possible.
Brake pad wear limit indica-
tors

4RUNNER (1998)
The brake pad wear limit indicators
on your disc brakes give a warning
noise when the brake pads are
worn to where replacement is re-
quired.
If you hear a squealing or scraping
noise while driving, have the brake
pads checked and replaced by your
Toyota dealer as soon as possible.
Expensive rotor damage can result if
the pads are not replaced when nec-
essary. Luggage stowage pr
ecau-
tions
When stowing luggage or cargo in the
vehicle, observe the following:
Put luggage or cargo in the lug-
gage compartment when at all pos-
sible. Be sure all items are se-
cured in place.
Be careful to keep the vehicle bal-
anced. Locating the weight as far
forward as possible helps maintain
balance.
For better fuel economy, do not
carry unneeded weight.
CAUTION
To prevent luggage or packages
from sliding forward during
braking, do not stack anything
in the luggage compartment
higher than the seatbacks. Keep
luggage or packages low, as
close to the floor as possible.
Never allow anyone to ride in
the luggage compartment. It is
not designed for passengers.
They should ride in their seats
with their seat belts properly
fastened. Otherwise, they are
much more likely to suffer seri-
ous bodily injury, in the event
of sudden braking or a colli-
sion.

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
(b) Starting the engine
Before starting the engine, be sure to
follow the instructions in º(a) Before
crankingº.
Normal starting procedure
The multiport fuel injection system/se-
quential multiport fuel injection system
in your engine automatically controls
the proper air- fuel mixture for starting.
You can start a cold or hot engine as
follows:
1. With your foot off the accelerator
pedal, crank the engine by turning the
key to ºSTARTº. Release it when the
engine starts.
2. After the engine runs for about 10
seconds, you are ready to drive.
If the weather is below freezing, let
the engine warm up for a few minutes
before driving.
If the engine stalls...
Simply restart it, using the correct
procedure given in normal starting.
If the engine will not startÐ
See ºIf your vehicle will not startº in
Part 4.
NOTICE
Do not crank for more than 30 seconds at a time. This mayoverheat the starter and wiringsystems.
Do not race a cold engine.
If the engine becomes difficult
to start or stalls frequently,have the engine checked im-mediately.
Always slow down in gusty cross-
winds. This will allow you much
better control.
Drive slowly onto curbs and, if
possible, at a right angle. Avoid
driving onto high, sharp- edged ob-
jects and other road hazards. Fail-
ure to do so can lead to severe
tire damage resulting in tire bursts.
When parking on a hill, turn the
front wheels until they touch the
curb so that the vehicle will not
roll. Apply the parking brake, and
place the transmission in ºPº (auto-
matic) or in first or reverse (manu-
al). If necessary, block the wheels.
Washing your vehicle or driving
through deep water may get the
brakes wet. To see whether they
are wet, check that there is no
traffic near you, and then press the
pedal lightly. If you do not feel a
normal braking force, the brakes
are probably wet. To dry them,
drive the vehicle cautiously while
lightly pressing the brake pedal
with the parking brake pulled. If
they still do not work safely, pull to
the side of the road and call a
Toyota dealer for assistance.
Tips for driving in various
conditions