1998 TOYOTA 4RUNNER instrument panel

4RUNNER (1998)
HEADLIGHTS
To turn on the following lights:
Twist the headlight/turn signal leverknob.
Position 1ÐParking, tail, license plate,
side marker and instrument panel
lights
Position 2ÐHeadlights and all of the
above
If you turn the ignition switch to the
ºLOCKº position with the headlights
left on, a buzzer reminds you to turn
the lights off when you open the driv-
er 's door.
NOTICE
To prevent the battery from being
discharged, do not leave thelights on for a long period whenthe engine is not running.
Daytime running light system (Cana-
da only)
The headlights turn on when the park-
ing brake is released with the engine
started, even with the light switch in
the ºOFFº position. They will not go
off until the ignition switch is turned
off.
To turn on the other exterior lights
and instrument panel lights, twist the
knob to the position 1. Under the daytime running light sys-
tem, the headlights turn on at reduced
intensity. Twist the knob to the posi-
tion 2 to turn to full intensity for driv-
ing at night.

4RUNNER (1998)
High- Low beams ÐFor high beams,
turn the headlights on and push the
lever away from you (position 1). Pull
the lever toward you (position 2) for
low beams.
The headlight high beam indicator light
(blue light) on the instrument panel
will tell you that the high beams are on.
Flashing the high beam headlights
(position 3)ÐPull the lever all the way
back. The high beam headlights turn
off when you release the lever.
You can flash the high beam head-
lights with the knob turned to ºOFFº.

4RUNNER (1998)
TURN SIGNALS
To signal a turn, push the head-
light/turn signal lever up or down to
position 1.
The key must be in the ºONº position.
The lever automatically returns after
you make a turn, but you may have
to return it by hand after you change
lanes.
To signal a lane change, move the
lever up or down to the pressure point
(position 2) and hold it.
If the turn signal indicator lights
(green lights) on the instrument panel
flash faster than normal, a front or
rear turn signal bulb is burned out. Emergency flashers

4RUNNER (1998)
To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To
turn them off, push the switch once
again.
Turn on the emergency flashers to
warn other drivers if your vehicle must
be stopped where it might be a traffic
hazard.
Always pull as far off the road as
possible.
The turn signal light switch will not
work when the emergency flashers are
operating.
NOTICE
To prevent the battery from being
discharged, do not leave theswitch on longer than necessarywhen the engine is not running.
Instrument panel light con-
trol

4RUNNER (1998)
To adjust the brightness of the
instrument panel lights, turn the knob. Interior light
To turn on the interior light, slide
the switch.
The interior light switch has the fol-
lowing positions:

4RUNNER (1998)
Lock release button
To prevent misshifting Parking, engine starting and key removal position Reverse position Neutral position Position for engine braking
With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in ºONºposition.) Shift while holding the lock release button in. Shifting normally Normal driving position Position for stronger engine braking than that in º2º posi- tion
Overdrive switch
For selecting either a three-speed or four-speed transmission
ºONº position(Shifting into overdrive pos-sible) ºOFFº position (Shifting into overdrive notpossible)ºO/D OFFº indicator light shows the over- drive switch is inOFF position
Driving pattern selector button For selecting a driving pattern suited to existing driving conditions
ºNORMº (Normal)mode for general driving conditioning ºPWRº (Power) mode for power- ful acceleration
ºPWRº mode indicator light on the instrument panel shows the driving pattern selector button isin the ºPWRº mode
Vehicles with cruise control ' When the cruise control is being used, even if you downshift the trans mission by turning
off the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to
decrease the vehicle speed, see ºCruise controlº in this chapter. Automatic transmission
Two- wheel drive models

4RUNNER (1998)
Lock release button
To prevent misshifting
Parking, engine starting and key removal position Reverse position Neutral position Normal driving position Position for engine braking Position for stronger engine braking than that in º2º posi- tion
With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in ºONºposition.) Shift while holding the lock release button in. Shifting normally Overdrive switch
For selecting either a three-speed or four-speed transmission
ºONº position(Shifting into overdrive pos-sible) ºOFFº position (Shifting into overdrive notpossible)ºO/D OFFº indicator light shows the over- drive switch is inOFF position
Driving pattern selector button For selecting a driving pattern suited to existing driving conditions
ºNORMº (Normal)mode for general driving conditioning ºPWRº (Power) mode for power- ful accelerationºPWRº mode indicator light on the instrument panel shows the driving pattern selector button isin the ºPWRº mode
Vehicles with cruise control ' When the cruise control is being used, even if you downshift the trans mission by turning
off the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to
decrease the vehicle speed, see ºCruise controlº in this chapter. Automatic transmission
Four- wheel drive control

4RUNNER (1998)
For easy unlocking, slightly turn the
steering wheel in either direction while
the vehicle is in motion.
When the differential lock is disen-
gaged, the indicator light will go out. The differential will also unlock if you
shift the front drive control lever out
of ºL4º. Never forget to turn off the
switch after using this feature.
To check the indicator bulb, turn the
ignition key to the ºONº position, but
do not start the engine.
CAUTION
Do not keep driving with the dif-
ferential lock switch on.
Parking brake
When parking, firmly apply the
parking brake to avoid inadvertent
creeping.
To set: Pull up the lever. For better
holding power, first depress the brake
pedal and hold it while setting the
brake.
To release: Pull up the lever slightly,
press the thumb button, and lower.To remind you that the parking brake
is set, the parking brake reminder
light in the instrument panel remains
on until you release the parking brake.