1998 TOYOTA 4RUNNER clutch

4RUNNER (1998)
To crank the engine without de-
pressing the clutch pedal, push the
switch with the ignition on.
The switch stays on as long as the
ignition is on. And it will automatically
turn off when the ignition is off.
This switch cancels the clutch start
system, which is desi gned to keep the
starter motor from operating if the
clutch pedal is not depressed all the
way down.
The switch allows the vehicle to be
driven out of difficult situations by
cranking the engine with the clutch engaged. Never use the switch for normal en-
gine starting. Be sure to follow the
starting procedure instructed in ºHow
to start the engineº in Part 3.
Clutch start cancel switch
(four- wheel drive models wi
manual transmission)

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Because of the added load of the
trailer, your vehicle's engine may
overheat on hot days (at tempera-
tures over 30 C [85 F]) when go-
ing up a long or steep grade with
a trailer. If the engine coolant tem-
perature gauge indicates overheat-
ing, immediately turn off the air-
conditioning (if in use), pull off the
road and stop in a safe spot. Refer
to ºIf your vehicle overheatsº in
Part 4 of this manual.
Always place wheel blocks under
both the vehicle and trailer wheels
when parking. Apply the parking
brake firmly. Put the transmission
in Pº (automatic) or in first or re-
verse (manual). Avoid parking on a
slope with a trailer, but if it cannot
be avoided, do so only after per-
forming the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the vehicle and trailer
wheels.
3. When the wheel blocks are in place, release your brakes slowly
until the blocks absorb the load.
4. Apply the parking brake firmly. 5. Shift into first or reverse (manual)
or ºPº (automatic) and turn off the
engine. When restarting out after parking on
a slope:
1. With the transmission in ºPº posi- tion (automatic) or the clutch pedal
depressed (manual), start the en-
gine. (With an automatic transmis-
sion, be sure to keep the brake
pedal depressed.)
2. Shift into gear.
3. Release the parking brake (also foot brake on automatic transmis-
sion vehicles) and slowly pull or
back away from the wheel blo cks.
Stop and apply your brakes.
4. Have someone retrieve the blo cks.
CAUTION
Do not exceed 72 km/h (45
mph) or the posted towing
speed limit, whichever is lower.
Because instab ility (swaying) of
a towing vehicle- trailer com-
bination usually increases as
the speed increases, exceeding
72 km/h (45 mph) may cause
loss of control.

4RUNNER (1998)
Slow down and downshift be-
fore descending steep or long
downhill grades. Do not make
sudden downshifts.
Avoid holding the brake pedal
down too long or too frequent-
ly. This could cause the brakes
to overheat and result in re-
duced braking efficiency.Getting more kilometers/mileage from
a liter/gallon of fuel is easyÐjust take
it easy. It will help make your vehicle
last longer, too. Here are some specif-
ic tips on how to save money on both
fuel and repairs:
Keep your tires inflated at the
correct pressure. Underinflation
causes tire wear and wastes fuel.
See Chapter 7- 2 for instructions.
Do not carry unneeded weight in
your vehicle. Excess weight puts
a heavier load on the engine, caus-
ing greater fuel consumption.
Avoid lengthy warm- up idling.
Once the engine is running smooth-
ly, begin drivingÐbut gently. Re-
member, however, that on cold win-
ter days this may take a little
longer.
Accelerate slowly and smoothly.
Avoid jackrabbit starts. Get into
high gear as quickly as possible.
Avoid long engine idling. If you
have a long wait and you are not
in traffic, it is better to turn off the
engine and start again later.
Avoid engine lug or overrevving.
Use a gear position suitable for the
road on which you are travelling.
Avoid continuous speeding up
and slowing down. Stop- and- go
driving wastes fuel.
Avoid unnecessary stopping and
braking. Maintain a steady pace.
Try to time the traffic signals so
you only need to stop as little as
possible or take advantage of
through streets to avoid traffic
lights. Keep a proper distance from
other vehicles to avoid sudden
braking. This will also reduce wear
on your brakes.
Avoid heavy traffic or traffic
jams whenever possible.
Do not rest your foot on the
clutch or brake pedal. This
causes needless wear, overheating
and poor fuel economy.
Maintain a moderate speed on
highways. The faster you drive,
the greater the fuel consumption.
By reducing your speed, you will
cut down on fuel consumption.
Keep the front wheels in proper
alignment. Avoid hitting the curb
and slow down on rough roads.
Improper alignment not only causes
faster tire wear but also puts an
extra load on the engine, which, in
turn, wastes fuel.
How to save fuel and make
your vehicle last longer, to
o

4RUNNER (1998)
Tire surface and wheel nuts
Check the tires carefully for cuts,
damage or excessive wear. See Chap-
ter 7- 2 for additional information.
When checking the tires, make sure
no nuts are missing, and check the
nuts for looseness. Tighten them if
necessary.
Tire rotation
Rotate the tires every 12000 km (7500
miles). See Chapter 7- 2 for additional
information.
Fluid leaks
Check underneath for leaking fuel, oil,
water or other fluid after the vehicle
has been parked for a while. If you
smell fuel fumes or notice any leak,
have the cause found and corrected
immediately.
Doors and engine hood
Check that all doors including back
door operate smoothly and all latches
lock securely. Make sure the engine
hood secondary latch secures the
hood from opening when the primary
latch is released. INSIDE THE VEHICLE
Items listed below should be
checked regularly, e.g. while per-
forming periodic services, cleaning
the vehicle, etc.
Lights
Make sure the headlights, stop lights,
tail lights, turn signal lights, and other
lights are all working. Check headlight
aim.
Service reminder indicators and
warning buzzers
Check that all service reminder indica-
tors and warning buzzers function
properly.
Steering wheel
Check that it has the specified free-
play. Be alert for changes in steering
condition, such as hard steering or
strange noise.
Seats
Check that all seat controls such as
seat adjusters, seatback recliner, etc.
operate smoothly and that all latches
lock securely in any position. Check
that the head restraint move up and
down smoothly and that the locks hold
securely in any latched position. For
folding- down rear seatbacks, swing- up
rear seat cushions and detachable
temporary third seat, check that the
latches lock securely.Seat belts
Check that the seat belt system such
as buckles, retractors and anchors op-
erate properly and smoothly. Make
sure the belt webbing is not cut,
frayed, worn or damaged.
Accelerator pedal
Check the pedal for smooth operation
and uneven pedal effort or catching.
Clutch pedal
Check the pedal for smooth operation.
Brake pedal
Check the pedal for smooth operation
and that the pedal has the proper
clearance. Check the brake booster
function.
Brakes
At a safe place, check that the brakes
do not pull to one side when applied.
Parking brake
Check that the lever has the proper
travel and that, on a safe incline, your
vehicle is held securely with only the
parking brake applied.

4RUNNER (1998)
Automatic transmission ºParkº mech- anism
Check the lock release button of the
selector lever for proper and smooth
operation. On a safe incline, check
that your vehicle is held securely with
the selector lever in ºPº position and
all brakes released.
IN THE ENGINE COMPARTMENT
Items listed below should be
checked from time to time, e.g.
each time when refueling.
Washer fluid
Make sure there is sufficient fluid in
the tank. See Chapter 7- 3 for addi-
tional information.
Engine coolant level
Make sure the coolant level is be-
tween the ºFULLº and ºLOWº lines on
the see- through reservoir when the
engine is cold. See Chapter 7- 2 for
additional information.
Battery electrolyte level
Make sure the electrolyte level of all
battery cells is between upper and
lower level lines on the case. Add
only distilled water when replenishing.
See Chapter 7- 3 for additional in-
formation. Brake fluid level
Make sure the brake fluid level is cor-
rect. See Chapter 7- 2 for additional
information.
Engine oil level
Check the level on the dipstick with
the engine turned off and the vehicle
parked on a level spot. See Chapter
7- 2 for additional information.
Power steering fluid level
Check the level through the reservoir.
The level should be in the ºHOTº or
ºCOLDº range depending on the fluid
temperature. See Chapter 7- 2 for
additional information.
Exhaust system
If you notice any change in the sound
of the exhaust or smell exhaust
fumes, have the cause located and
corrected immediately. (See engine ex-
haust cautions in Part 2.)
Be on the alert for changes in perfor-
mance, sounds, and visual tip- offs
that indicate service is needed. Some
important clues are as follows:
Engine missing, stumbling, or ping-
ing
Appreciable loss of power
Strange engine noises
A leak under the vehicle (however,
water dripping from the air condi-
tioning after use is normal.)
Change in exhaust sound (This
may indicate a dangerous carbon
monoxide leak. Drive with the win-
dows open and have the exhaust
system checked immediately.)
Flat- looking tire; excessive tire
squeal when cornering; uneven tire wear
Vehicle pulls to one side when
driving straight on a level road
Strange noises related to suspen-
sion movement
Loss of brake effectiveness;
spongy feeling brake or clutch ped-
al; pedal almost touches floor; ve-
hicle pulls to one side when brak-
ing
Engine coolant temperature continu-
ally higher than normal
Does your vehicle need
repairing?

4RUNNER (1998)
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
3RZ- FE engineWith rear heater 11.0 (11.6, 9.7)
Without rear heater
10.0 (10.6, 8.8)
5VZ- FE engine With rear heater
9.0 (9.5, 7.9)
Without rear heater
8.0 (8.5, 7.0) Coolant type:
With ethylene- glycol antifreeze
(Do not use alcohol type.)
BATTERY
Open voltage *
at 20 C (68 F):
12.6Ð12.8 V Fully charged
12.2Ð12.4 V Half charged
11.8 Ð12.0 V Discharged
* : Voltage that is checked 20 minutes
after
the key is removed with all the lights
turned off
Charging rates:
5 A max.
CLUTCH
Pedal freeplay, mm (in.): 5Ð15 (0.2Ð0.6)
Fluid type: SAE J1703 or FMVSS No. 116 DOT
3 MANUAL TRANSMISSION
Oil capacity, L (qt., Imp. qt.):
3RZ- FE engine
Two- wheel drive models 2.6 (2.7, 2.3)
Four- wheel drive models
2.5 (2.6, 2.2)
5VZ- FE engine 2.2 (2.3, 1.9)
Oil type: Gear oil API GL- 4 or GL- 5
Recommended oil viscosity: SAE 75W- 90
AUTOMATIC TRANSMISSION
Fluid capacity (drain and ref ill),
L (qt., Imp. qt.): Two- wheel drive models Up to 1.6 (1.7, 1.4)
Four- wheel drive models Up to 2.0 (2.1, 1.8)