1998 SSANGYONG MUSSO manual transmission

AUTOMATIC TRANSMISSION 5A-95
Notice
Care must be taken when applying sealant to ensure that it is
not applied between the pin and the lever.
5. Assemble the park rod lever, complete with the return spring
and pivot pin, applying a small amount of sealant to the
outer end of the pivot pin.
Notice
That the lever must pivot freely on its pin and the spring
must return the park rod lever to its correct location.
6. Secure the pivot pin with the circlip.
Notice
The pawl must pivot freely on its pin.
7. Install the parking pawl pivot pin and spring.
8. Connect the park rod to the manual valve detent lever.
Ensure the spring and cam collar is firmly installed on the
rod.

5A-96 AUTOMATIC TRANSMISSION
9. Check that the cam collar slides freely on the rod.
10. Insert the cross shaft into the case, from the side opposite
to the inhibitor switch, then install the anti-rattle spring on
the shaft.
11. Position the manual valve detent lever, aligning it with the
cross-shaft bore in the case.
12. Push the shaft through the detent lever until it starts in the
detent lever side of the case.
13. Install the detent lever drive pin in the shaft using tool No.
0555-331897 with the adaptor over the pin.
14. Press the pin into the shaft until the tool bottoms.
15. Remove the tool and fit the spring retaining circlip to the
shaft.
16. Install the new cross shaft seals using tool No. 0555-
331894.
17. Install the inhibitor switch on the case. Torque the screws
as per specifications. Press the pin into the shaft until the
tool bottoms (4WD models) using tool No.0555-332942.
18. Thoroughly check the terminal wiring loom for condition
and continuity.
19. Position the loom and locate the solenoid 7 contact and
terminal in the pump mounting flange at the front of the
case. The solenoid 7 wire is routed under the park rod
and cross shaft in the case.

5A-124 AUTOMATIC TRANSMISSION
27. Install the line pressure plug and tighten to specification.
Refer to figure 8.62.
28. Install the detent spring assembly (spring, support plate
and screw), ensuring that the screw is tightened to
specification. Check the spring for wear or damage.
29. Install the manual shift valve. Refer to figure 8.60.
Notice
Be aware that the manual valve will fall out of the valve
body.
Figure 8.62 - Wiring Installation
Figure 8.60 - Manual Shift Valve

AUTOMATIC TRANSMISSION 5A-125
30. Align the valve body assembly on the transmission case
and install the manual valve lever to manual valve link. Fit
the long end of the link to the manual valve first. Install the
securing bolts and tighten to specification in the specified
sequence. Refer to figure 8.61.
31. Check the alignment of the detent roller and the manual
lever quadrant.
32. Connect the solenoid wiring as detailed below:
lSolenoid 1 - red
lSolenoid 2 - bIue
lSolenoid 3 - yellow
lSolenoid 4 - orange
lSolenoid 5 - green
lSolenoid 6 - violet (Refer to figure 8.62.)
Notice
All hardware must be correctly installed and torqued to
specification.
Figure 8.61 - Tightening Sequence Valve Body to Case

Model
Type
Gear Ratio
Oil
Weight (Dry)
SECTION 5B
MANUAL TRANSMISSION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 5B-1
General Specifications . . . . . . . . . . . . . . . . . . 5B-1
Fastener Tightening Specifications . . . . . . . . . 5B-2
External View . . . . . . . . . . . . . . . . . . . . . . . . 5B-3
Gear Train . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-3
Power Flow . . . . . . . . . . . . . . . . . . . . . . . . . 5B-4
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5
Will not Shift (Control Lever Moves) . . . . . . . . 5B-5
Hard Shift or Control Lever Will not Move Into
Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5
Gears Crash When Shifting . . . . . . . . . . . . . . 5B-5
Transmission Jumps Out . . . . . . . . . . . . . . . . . 5B-6
Transmission Locked in One Gear . . . . . . . . . 5B-6
Transmission Noise . . . . . . . . . . . . . . . . . . . . . 5B-6
Transmission Leakage . . . . . . . . . . . . . . . . . . 5B-7Diagnosis Table . . . . . . . . . . . . . . . . . . . . . . . 5B-8
Component Locator . . . . . . . . . . . . . . . . . . . 5B-9
Maintenance and Repair . . . . . . . . . . . . . . 5B-11
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 5B-11
Shift Control Cable . . . . . . . . . . . . . . . . . . . . 5B-11
Transmission . . . . . . . . . . . . . . . . . . . . . . . . 5B-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17
Major Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17
Main Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-27
Input Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-32
Counter Shaft . . . . . . . . . . . . . . . . . . . . . . . . 5B-34
Extension Housing . . . . . . . . . . . . . . . . . . . . 5B-35
Shift Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-36
Inspection of Components . . . . . . . . . . . . . . 5B-40
Pre-Installation Checks . . . . . . . . . . . . . . . . . 5B-45
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Description
T5WC
Floor Change
3.97 : 1
2.34 : 1
1.46 : 1
1.00 : 1
0.85 :1
3.71 : 1
ATF DEXRON II / III
3.4 L
Check : Every 15,000km, Replace : Every 50,000km
33kg 1st
2nd
3rd
4th
5th
Reverse
Specification
Capacity(litre)
Change Interval
Notice
Add LUBRIZOL (280cc) in oil after overhauling.

5B-2 MANUAL TRANSMISSION
FASTENER TIGHTENING SPECIFICATIONS
Application
Transmission
Oil Filler Plug
Transmission Mounting Bolt (Housing)
Oil Drain Plug
Front Propeller Shaft (T/C)
Rear Propeller Shaft (T/C)
Cross Member Bolt (Center)
Cross Member Bolt (Side)
Control Cable
Shift Lever BoltNlm
25
77 - 87
25
81 - 89
70 - 90
21 - 35
62 - 93
20 - 30

MANUAL TRANSMISSION 5B-3
EXTERNAL VIEW
GEAR TRAIN

5B-4 MANUAL TRANSMISSION
POWER FLOW