1998 SSANGYONG MUSSO drain bolt

5B-26 MANUAL TRANSMISSION
21. Completely compress the detent spring.
22. To install the extension housing to the case, apply sealer
to the top two bolts and tighten them and tighten the 6
bolts.
23. Apply sealer to the back-up lamp switch and drain plug
and tighten them.
24. Using a hammer, install the offset lever-to-shift roll pin.
25. Turn the transmission case reversely and place a dial
indicator on the extension housing. Move the input and
main shift up and down and measure end play. Select a
shim which is the same thickness as the measurement (±
0.001 inch). After shim installation, the end play should be
‘0’.
26. Remove the input bearing retainer and do the following :
lInstall the adjusting shim behind the input bearing outer
race in the retainer and if 2 shims are used, install the
thinner one in first.
lInstall the retainer to the case and tighten the bolts.
lIf end play is not ‘0’change the shim again.
lApply RTV sealant to the sealing surface of the retainer.
lApply sealer to the 4 retainer bolts and tighten them.
27. Remove the fill plug.
28. Remove the transmission from the holding fixture and install
it to the vehicle.
29. Clean the sealing surface of the shift control lever.
30. Install the control cables to the shift lever.

TRANSFER CASE (PART TIME 4408) 5D1-3
Cannot Front Wheel Drive when Shifted 4H,4L
DIAGNOSIS
Electric Shift Problems
Action
Overhaul and check, replace if necessary.
Overhaul and check for wear and damage.
Replace if necessary.
Check sliding parts, replace if necessary. Checks
Faulty or Damaged TCCU, Speed Sensor, Motor, Clutch
or Internal Wirings
Damaged or Worn Shift Cam, Hub, Fork and Rail Shift
Binding Shift Fork, Hub Collar or Gear
Checks
Broken Drive ChainAction
Check sliding parts, replace if necessary.
Noise in 4WD Operation
Checks
Improper or low oil
Loosened bolts or mounted parts
Noisy T/C bearing
Noisy gearsAction
Drain and replace with specified oil.
Retighten as specified.
Disassemble bearings and parts and check for wear or
damage. Replace if necessary.
Check for wear and damage including speedometer
gear, replace if necessary.
Noise in 4H or 4L
Checks
Worn or Damaged Sprockets or Drive Chain
Incorrect Tire PressureAction
Disassemble and check for wear and damage, replace
if necessary.
Adjust tire pressure.
Transfer Case Oil Leakage
Action
Replace the case.
Clean case and parts and check for leakage.
Remove breather hose and clean, replace if necessary.
Use specified oil and adjust oil level.
Retighten
Use specified sealant and retighten.
Replace Checks
Cracked Transfer Case
Leakage from Other Parts
Breather Clogging
Improper or too much Oil
Loosened Sealing Bolts
Improperly Applied Sealant
Worn or Damaged Oil Seal

5D1-12 TRANSFER CASE (PART TIME 4408)
Removal & Installation Procedure
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the drain plug and drain the oil.
Reinstall the drain plug.
* If planar damper is installed, unscrew 4 bolts and remove
the planar damper.
Installation Notice
Tightening Torque 19 - 30 Nm
4. Remove the breather hose.
5. Disconnect the speedometer cable connector and other
cable connectors and wiring harnesses.
6. Support the transfer case with jack and remove the front
and rear propeller shafts from the transfer case.
Installation Notice
Front
Rear81 - 89 Nm
70 - 80 NmTightening Torque

TRANSFER CASE (TOD) 5D2-35
Removal & Installation Procedure
1. Disconnect (-) cable from battery.
2. Lift on vehicle and make sure on safety.
Notice
Be careful for catalytic converter due to high temperature
after driving or engine running.
3. Prepare a vessel to drain transfer case and manual
transmission oil.
4. Release drain plug and drain transfer case and manual
transmission oil.
If planar damper is installed, unscrew 4 bolts and remove
the planar damper.
Notice
Oil drain should be along with whole transfer case
disassembly and assembly.
5. Disconnect transmission extension wiring connector back
side transfer case.
Notice
When disconnect connector, make sure on direction of
locking tab towards inside.
6. Disconnect shift motor/clutch coil connect (Black 7 pin)
connector upper backside.
7. Disconnect front and rear speed sensor connector (white
7 pin).
8. Disconnect speedometer sensor connector right upper
side.
9. Disconnect breather tube front upper side transfer case
(upper connecting point of transfer case and front
propeller).
10. Prepare hydraulic jack and support transfer case assembly.

6A-8 POWER STEERING SYSTEM
Tightening Torque 35 - 45 Nm
Removal & Installation Procedure
1. Remove the cotter pin and nut and separate the steering
gear box tie rod from the steering knuckle arm using the
puller.
Installation Notice
2. Remove the bolt and separate the lower sha from the
steering gear box.
Installation Notice
Tightening Torque 30 - 40 Nm
3. Remove the oil pipe from the steering gear box and drain
the oil.
Installation Notice
4. Remove the clamp bolts and remove the steering gear box
assembly.
Installation Notice
Tightening Torque 12 - 18 Nm
Notice
lBe careful not to damage the rubber(1).
lWhen installing tighten the bolt (3) with the rubber
(2)being inserted to the hole of clamp.
5. Bleed the air from system.
6. Check the toe-in.
Tightening Torque 70 - 90 Nm Tighten the bolt toward threadless side of lower shaft
coupling.

9Q-4 ROOF
Removal & Installation Procedure
1. Disconnect the connector and remove the sun roof module
assembly.
2. Disconnect the front and rear drain hose.
3. Unscrew the sun roof mounting bracket bolts(arrows) and
remove the inner sliding and sun roof assembly