1998 SSANGYONG MUSSO fuel pump

M162 ENGINE CONTROLS 1F1-31
FUEL PUMP TEST
Preparation
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Stop Watch
5 Measuring Beaker
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Connect the test box to the ECU.0 3 Test Box
04 ECU Test Cable
Tools Required
103 589 00 21 00 Pressure Tester
210 589 00 99 00 Adaptor Line
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

1F1-32 M162 ENGINE CONTROLS
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
1 liter of fuel
supply for
max. 35
seconds· ·· ·
· Fuel pump:
- Fuel supply
ratio· Ignition:ON
- Disconnect the fuel
return pipe and
connect the host to
beaker to collect the
supplied fuel Þ 1.0· Þ 2.0
· Check the fuel line
5 - 9 A
· ·· ·
· Fuel pump:
- Current
consumption· Ignition:ON
- Remove the fuel
relay from the fuse
and relay box in
luggage
compartment and
connect the
amperemeter
between No.1 and
No.3 in relay
box(fuel pump relay
removed position)
for measuring
current consumption Þ 2.0· Fuel pump
533
Multi tester(DC current)
31

1F1-38 M162 ENGINE CONTROLS
Pin No.Abbreciation Decription
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60BRS
-
-
-
-
-
KLIKU
-
-
-
GND
SP1+5V
KP
TEV
ML
-
CAN L
CAN H
-
-
-
-
KPI
KLIMA
KLIMA
-
SP1S
SP2S
BLS
GND
SP2+2.5V
S+B
WA
S-B
KSK
-
AUS
DIAG
V-SIG
TN-SIG Brake switch
-
-
-
-
-
Air conditioning clutch relay
-
-
-
Pedal potentiometer 1 ground
Pedal potentiometer 1 supply
Fuel pump relay
Tank purge valve
Engine fan (H1)
-
CAN-Low
CAN-High
-
-
-
-
Clutch switch
Air conditioning
Electronic traction signal
-
Pedal potentiometer 1 signal
Pedal potentiometer 2 signal
Brake light switch
Pedal potentiometer 2 ground
Pedal potentiometer 2 supply
Cruise accelerate/Set
Cruise resume
Cruise decelerate/Set
Cruise safety contact switch
-
Cruise off switch
Diagnostics (k-line)
Vehicle speed signal
Engine speed signal

1F1-42 M162 ENGINE CONTROLS
Pin No.Description
Pedal potentiometer 1 ground
Pedal potentiometer 1 supply
Fuel pump relay
Tank purge valve
Engine fan
-
CAN-Low
CAN-High
-
-
-
-
Clutch switch
Air conditioning
Electronic traction signal(ABD)
-
Pedal potentiometer 1 signal
Pedal potentiometer 2 signal
Brake light switch
Pedal potentiometer 2 ground
Pedal potentiometer 2 supply
Cruise accelerate/Set
Cruise resume
Cruise decelerate/Set
Cruise safety contact switch
-
Cruise off switch
Diagnostics(K-line)
Vehicle speed signal
Engine speed signal31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60GND
SP1+5V
KP
TEV
ML
-
CAN L
CAN H
-
-
-
-
KPL
KLIMA
ETS
-
SP1S
SP2S
BLS
GND
SP2+2.5V
S+B
WA
S-B
KSK
-
AUS
DIAG
V-SIG
TN-SIGl
l
l
l
l
-
l
l
-
-
-
-
¡
l
¡
-
l
l
¡
l
l
¡
¡
¡
¡
-
¡
l
l
ll
l
l
l
l
-
l
l
-
-
-
-
¡
l
¡
-
l
l
¡
l
l
¡
¡
¡
¡
-
¡
l
l
l
Remarks
AbbreviationE32 ENG,
5speed M/T E32 ENG,
4speed A/T
(BTRA)

1F1-48 M162 ENGINE CONTROLS
A . Valves Closed
B. Valves Opened
The pressure difference between the fuel pressure and the
intake manifold is about 3.8 bars during the full load.

The spring chamber(9) is connected to the intake manifold
with the vacuum hose at the intake pipe connection(7). The
negative pressure generated in the intake manifold activates
the diaphragm, and thus the fuel pressure gets reduced to the
rate of the operating extent of the diaphragm by the intake
manifold's negative pressure.
Consequently, the fuel pressure in the fuel distributor changes
by the intake manifold's negative pressure, and the injector's
fuel pressure gets reduced independently to the throttle valve's
position. Thus, the fuel injection volume can only be determined
according to the injector's injecting duration.
2. Fuel return line
3. Valve
5. Diaphragm
6. Compression Spring
8. Fuel Chamber
9. Spring Chamber
1. Fuel Pressure Regulator
2. Intake Manifold
3. Fuel Return(to fuel tank)
4. Fuel Supply(form fuel pump)
5. Fuel Pressure(approx. 3.8 bars)
6. Intake Manifold Negative Pressure(0 bar)
Function of the Fuel Pressure Regulator
The fuel pressure regulator maintains the fuel pressure in the
fuel line with the pressure of 3.2 bars to 3.8 bars according to
the intake manifold pressure. This operating pressure cannot
be changed, and the fuel injection volume will be only
determined by the injection time. Over supplied fuel returns to
the fuel tank through the return line.

There is no negative pressure applied to the spring chamber(9)
during the full load, and it is separated from the fuel chamber(8)
by the diaphragm(5).
When the fuel pressure goes up, the diaphragm forces the
compression spring(6) in the direction of compression . At this
moment, the valve(3) sticks to the diaphragm by the fuel
pressure, and the fuel return line(2) opens. The fuel over
supplied returns to the fuel tank through the return line.

M162 ENGINE CONTROLS 1F1-49
The pressure difference between the fuel pressure and
the intake manifold is approx. 3.2 bars during idling.

1. Fuel Pressure Regulator
2. Intake Manifold
3. Fuel Return(to fuel tank)
4. Fuel Supply(from fuel pump)
7. Fuel Pressure(approx. 3.2 bars)
8. Intake Manifold Negative Pressure(0.6 bars)
A. Fuel pressure
B. Intake Manifold Negative Pressure
LL. Idling
TL. Partial load
VL. Full load

M162 ENGINE CONTROLS 1F1-53
3. If there is no change in fuel pressure and maintain the
following pressure over 30 minutes, it is normal.
Internal Leakage Test
1. Connect the fuel pressure gauge to the fuel pressure test
connector.
2. Stop the engine for approx. 30 minutes and then check the
fuel pressure changes.
Fuel pressure
drops slowly
·Fuel leakage at the
injector
• Faulty fuel pressure
regulator's
diaphragm and O-
ring.
Fuel pressure
drops rapidly• Faulty check valve
in the fuel pump.
Possible Cause Pressure Change
Fuel Pressure(bar) 2.5
Discharging the pressure in fuel system
1. Remove the fuel pressure test connector.
Installation Notice
2. Remove the fuel pressure in fuel system by pressing the
service valve with a clean, pointy tool.
Notice
Place a cloth so that the fuel doesn't stain around.
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE CONTROLS 1F1-57
FUEL FILTER
1 Fuel Filter
2 Outlet
Removal & Installation Procedure
1. Open the fuel tank cap and remove the fuel tank pressure.
2. Remove the fuel at (2) and in (3).
Installation Notice
Notice
Place the fuel pump pad. There may be a corrosion due to
the contact between the fuel filter and the bracket.
4. Check for leaks by operating the engine.
Notice
Installation should follow the removal procedure in the
reverse order. 3. Remove the mounting bracket bolt (4) and remove the fuel
filter (1).
Installation Notice3 Inlet
Tightening Torque
25 - 30 Nm
Tightening Torque
4 - 8 Nm