1998 SSANGYONG MUSSO fuel pump

OM600 ENGINE MECHANICAL 1B3-65
11. Remove the alternator bracket (16).
9. Disconnect the pipes of power steering pump and remove
the belt pulley.
Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then remove the
power steering pump.
12. Remove the fuel filter.

1B3-66 OM600 ENGINE MECHANICAL
18. Remove the timing case cover (19) bolts and then remove
the timing case cover (14).
Notice
Be careful not to damage the cylinder head gasket or oil
pan gasket.
13. Remove the camshaft.
14. Remove the socket bolts(4) in the chain box.
Socket Wrench 115 589 03 07 00
15. Remove the injection pump.
Notice
See the ‘Removal of fuel injection pump’.
16. Remove the oil pan bolts (8, 9) in the area of the timing
case cover (14).
17. Slightly loosen the remaining oil pan bolts.

OM600 ENGINE MECHANICAL 1B3-69
10. Install the fuel filter.
11. Install the vacuum pump.
12. Install the power steering pump.
13. Install the power steering pump pulley.
Tightening Torque 25 Nm
Tightening Torque 10 Nm
Tightening Torque 23 Nm
Tightening Torque 32 Nm
14. Install the guide pulley bracket.
Tightening Torque 9 Nm

1B3-92 OM600 ENGINE MECHANICAL
28. Remove the connecting rod bearing cap.
29. Install the piston.
30. Rotate the crankshaft by hand and check whether it rotates
smoothly.
31. If the bearings are damaged,
- replace the oil presser relief valve.
- clean the oil pump and oil filter housing carefully and
replace the hose if necessary.
Notice
After assembling the engine, check the camshaft timing,
adjust the start of fuel injection and check the TDC sensor
bracket setting.
32. Fill oil and run the engine and then check the oil pressure
and oil level.
Notice
Install the original oil filter element and then change the
engine oil and oil filter element after 1,000 - 1,500km. 27. Measure the radial clearance (L) of the connecting rod
bearing.
Example)Measured value ‘J’ = 47.700mm
Measured value ‘K’ = 47.653mm
Clearance ‘L’ = 0.047mm
Radial Clearance ‘L’ 0.026 - 0.068mm
Notice
If the clearance is out of standard, adjust the radial
clearance of connecting rod bearing by replacing the
connecting rod bearing shells. 26. Measure connecting rod bearing journal diameter (K).
Notice
Refer to measurement of the crankshaft bearing journal
diameter.
24. Insert the new connecting rod bearing shells into the
connecting rod and connecting rod bearing cap and tighten
the 12-sided stretch bolts (11).
25. Measure inner diameter of connecting rod bearing.
Tightening Torque 40 Nm + 90°

SECTION 1F1
M162 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F1-2
Fastener Tightening Specifications . . . . . . . . 1F1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F1-3
Schematic and Routing Diagrams . . . . . . . 1F1-4
E32 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F1-4
E32 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F1-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Failure Code . . . . . . . . . . . . . 1F1-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F1-10
Fuel Injection System Test (MSE3.62) . . . . . 1F1-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F1-21
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F1-26
Air Conditioner Control System Test . . . . . . 1F1-28
Fuel Pressure and Internal Leakage Test . . 1F1-29
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F1-31Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F1-33
Maintenance and Repair . . . . . . . . . . . . . 1F1-35
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F1-35
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-35
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F1-46
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F1-50
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F1-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F1-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F1-65
Camshaft Position Sensor . . . . . . . . . . . . . 1F1-67
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F1-69
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F1-72
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F1-74
Coolant Temperature Sensor . . . . . . . . . . . 1F1-75
Accelerator Pedal Module . . . . . . . . . . . . . . 1F1-78

M162 ENGINE CONTROLS 1F1-7
41
44
45
56
57
58
59
60
62
64
65
66
67
71
72
73
74
75
76
77
78
79
80
81
82
83
86
87
89 00
01
02
03
04
05
08
09
10
11
17
18
19
20
21
23
24
25
26
27
29
30
31
34
35
40
Failure
codeDescription
Coolant temperature sensor open
Coolant temperature sensor short
Coolant temperature sensor signal failure
Intake temperature sensor open
Intake temperature sensor short
Intake temperature sensor signal failure
Low battery voltage
HFM sensor signal failure
HFM sensor signal failure(Low)
HFM sensor signal failure(High)
Crankshaft position sensor signal failure
(no engine revolution signal)
Crankshaft position sensor signal failure
(rpm > max. value)
No.1 cylinder recognition failure
Crankshaft position sensor signal failure
(gab recognition failure)
Transmission coding failure
CAN communication failure : ASR
-
Transponder signal failure
CAN communication failure : TCU(A/T only)
CAN communication failure : TOD(E32 only)
-
-
CAN communication failure :
communication initialization failure
Fuel pump relay short(PWR)
Fuel pump relay open/short(GND)
Purge valve short
Failure
codeDescription
Purge valve open/short
Condenser fan(HI) relay short(PWR)
Condenser fan(HI) relay short(GND)
No.1 knock sensor signal failure
No.2 knock sensor signal failure
No.1 cylinder synchronization failure
-
-
Cluster S/W defectave
No ignition voltage output(No.1 ignition coil)
No ignition voltage output(No.2 ignition coil)
No ignition voltage output(No.3 ignition coil)
Crankshaft position sensor adaptation failure
Start signal recognition failure
No.1 injector short(PWR)
No.1 injector open/short(GND)
No.2 injector short(PWR)
No.2 injector open/short(GND)
No.3 injector short(PWR)
No.3 injector open/short(GND)
No.4 injector short(PWR)
No.4 injector open/short(GND)
High oxygen sensor voltage
Low oxygen sensor amplifying voltage
Oxygen sensor operating failure
Not excessive lean indication in oxygen
sensor(during coasting)
Oxygen sensor heater short(PWR)
Oxygen sensor heater open/short(GND)
Low oxygen sensor voltage
SELF DIAGNOSIS FAILURE CODE

M162 ENGINE CONTROLS 1F1-13
Failure
codeItemChecking method Te s t
stepRequirement
Specified
valuePossible cause
Þ 6.1· Ignition:ON0.1 - 0.3A· Cable
· Fuel pump relay
· ECU
· ·· ·
· Fuel pump
relay:
- Current
consumption
00,
01,
02,
06,Þ 7.0· ·· ·
· Coolant
temperature
sensor:
- Voltage79 78· Ignition:ON°CV
20 3.57
80 1.22
100 0.78· Þ 7.1
· ECU
±5% Þ 6.0
· Ignition:ON
(Fuel pump relay will
operate for 1 - 2
seconds when the
ignition switch is
turned to "ON" after
stopping the engine)
· Engine:cranking 33 11
· Cable
· Fuel pump relay
· ·· ·
· Fuel pump
relay:
- Operation34,11 - 14V
(approx.1-
2sec.)
11 - 14V
(Cranking or
driving)
533
Þ 7.1· Ignition:OFF
(Remove the No.2
coupling from ECU) 79 78· Þ 7.2
· Cable
· ·· ·
· Coolant
temperature
sensor:
- Resistance
& cable°CW
20 2500
80 322
100 185
±5%
Þ 7.2· ·· ·
· Coolant
temperature
sensor:
- ResistanceCoolant temperature
sensor:
14
· Remove the
connector from
coolant temperature
sensor and measure
the resistance
between No.1 and
No.2 pin with
multimeter.· Þ refer to
specified
resistance
value of 7.1· Coolant
temperature
sensor 34,
35,

1F1-30 M162 ENGINE CONTROLS
Failure
codeItemChecking method Te s t
stepRequirementSpecified
valuePossible cause
3.2 - 3.6 bar· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
applied· Engine:in idling
- Close the valve
screw on pressure
testerÞ 1.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Þ Fuel pump test
· Fuel pressure
regulator
3.7 - 4.2 bar
· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
not applied· Engine:in idling
- Close the valve
screw on pressure
tester Þ 2.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Fuel pressure
regulator
> 3.0 bar
· ·· ·
· Fuel system
internal
leakage:· Engine:stop Þ 3.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· The pressure drops
rapidly:non-return
valve in fuel pump
> 2.5 bar· After 30 minutes from
engine stop· The pressure drops
slowly:
- Injector test
- Fuel pressure
regulator
- O-ring