1998 SSANGYONG MUSSO automatic transmission fluid

5A-112 AUTOMATIC TRANSMISSION
Pump Cover and Converter Support
Notice
1. Do not wash the nose of solenoids in solvent.
2. Ensure that the correct ‘O’ ring is fitted for the application.
3. Do not mix up the low first blow-off and the torque converter
blow-off ball springs.
4. Be careful not to damage the needle bearings on the
assembly. Avoid any axial impact loads during assembly.
5. Check the transmission end float. This will help to detect
any missing parts or incorrect assembly.
Notice
Figure 8.35 shows the orientation of the cross- sections for
figures 8.36 to 8.42.
To assemble the pump cover and converter support
(refer to figures 8.34 and 8.35), proceed as follows.
1. Check the pump body for any damage, chips or irregularity.
Check that the bush is firmly staked in the drive gear.
2. Install the seal flush with the front face of the pump body.
3. Lubricate the pump bush, and the drive and driven gears,
with automatic transmission fluid.
4. Install the pump driven gear and the pump drive gear into
the pump body.
5. Using a straight edge and thickness gauge, check that the
clearance between pump face and gears is 0.04 - 0.018
mm.
6. Lubricate the pump body ‘O’ ring with automatic transmission
fluid and fit it to the pump body. Put the pump body to one
side.
7. Ensure that the pump cover cavities, ports and holes are
clean and free of any obstruction.
8. Lubricate all loose parts with automatic transmission fluid
prior to assembly.Figure 8.34 - Pump, Cover and Converter
Support
Figure 8.35 - Pump Cover Assembly

5A-126 AUTOMATIC TRANSMISSION
Oil Filter and Pan Assembly
Notice
1. Replace the filter whenever rebuilding a transmission where a significant amount of mechanical damage has
occurred.
2. To aid the assembly of the pan gasket, use a small amount of Vaseline at the pan/gasket interface. This ensures
that the gasket remains on the pan ridge. Do not over torque pan bolts as this may distort the pan and cause
leaks.
3. Ensure that the internal line pressure plus in the valve body is fitted.
To assemble the oil filter and pan assembly (refer to figures 8.63 and 8.64), proceed as follows.
1. Lubricate the oil filter sealing ring with automatic transmission fluid.
2. Carefully assemble the oil filter to the valve body. The spigot must not lean on one side while being fitted. Refer to
figure 8.63.
3. Secure the oil falter assembly with the retainer.
4. Check that the magnet is located in the dimple in the comer of the oil pan.
5. Assemble the gasket on the pan lip. The gasket must be free of any distortion when installed.
6. Fit the oil pan assembly to the transmission case and tighten the securing bolts to specification and sequence
(refer to figure 8.65). Do not over torque.

TRANSFER CASE (TOD) 5D2-47
Assembly Procedure
Assembly
Before assembly, lubricate all parts with Automatic Transmission
Fluid or equivalent.
1. If removed, drive the bearing into the front output case bore.
Drive the bearing in staight, making sure it is not cocked in
the bore. Install the internal snap ring that retains the bearing
to the front case.
2. If removed, install the front yoke to flange seal in the front
case bore.
3. If removed, install the yoke to flange seal into the mounting
adapter bore.
4 Sun Gear
5 Thrust Plate
6 Input Shaft
7 Thrust Washer
8 Bearing
9 External Snap Ring
10 Internal Snap Ring
4. If the input shaft needle bearing and bushing were removed,
install a new bearing and bushing as detailed in the following
steps:
Press a new needle bearing, then a new bushing in the
input shaft as follows:
a. Position the input shaft on Axle Bearing/Seal Plate or
equivalent, and Pinion Bearing Cone Replacer as a
spacer.
b. Press a new needle bearing into the end of the input
shaft until it seats in the input shaft.
c. Press in a new bushing.
5. The recessed face of the sun gear and the snap ring groove
on the bearing outer race should be toward the rear of the
transfer case. The stepped face of the thrust washer should
face toward the bearing.
Slide the sun gear, thrust plate and thrust washer into
position on the input shaft. Press the bearing over the input
shaft. Install the external snap ring to the input shaft.

5D2-48 TRANSFER CASE (TOD)
6. Install the front planet to the sun gear and input shaft.
Install the internal snap ring to the planetary carrier.
7. Place the tanged snap ring in the case. Expand snap ring
with snap ring pliers and install planetary carrier assembly.
Check installation by holding the case and carefully tapping
the face of the input shaft against a wooden block to make
sure the snap ring is installed.
8. Remove all traces of gasket sealant from the front case
and mounting adapter mating surfaces. Install a bead of
gasket sealant on the surface of the front case.
9. Install the high-low shift fork and high-low collar as an
assembly into the front planet.
Notice
Make sure that the nylon wear pads are installed on the
shift fork and snapped securely into place.
12 Rear Output Shaft
13 Oil Strainer
14 Coupling Hose
15 Hose Clamp
16 Pump Body
10. If new pump is used, align the flat of the output shaft and
the flat of the pump. Slide the pump onto the output shaft.
lDo not disassemble oil pump. It is serviced only as an
assembly. Check the pump to make sure the pump
rotates freely.
lDo not remove the plastic insert from the bore of the
new pump. Discard it after it slides out during pump
installation to the rear output shaft.
lWhile turning the output shaft, prime the pump through
the oil filter pickup tube or housing inlet hole with clean
Automatic Transmission Fluid or equivalent.
11. Inspect the outside surfaces and bore of the oil pump. If
there is no discoloration in the pump housing, gear or cover,
and the pump bore and the lube holes of the output shaft
show evidence of oil, the pump is working.

TRANSFER CASE (TOD) 5D2-53
40. Install the rear case flange on the output shaft. Install the
rubber seal, output shaft yoke washer and nut. Tighten
the nut.
Tightening Torque 137 - 196 Nm
41. Install the drainplug and tighten.
42. Fill the transfer case with 1.4 liters of Automatic
Transmission Fluid or equivalent.
Notice
Fluid level should be just below the filler plug hole.
Tightening Torque 19 - 30 Nm
Tightening Torque 19 - 30 Nm 43. Install the fill pulg and tighten.
44. Install the transfer case as outlined in removal and
Installation, transfer case in the section.
Notice
Make sure proper drain and fill plugs are installed if case
is replaced.