1998 SSANGYONG MUSSO torque

1B1-10 M162 ENGINE MECHANICAL
10. Remove the upper mounting bolts of radiator and then
remove the radiator.
7. Loosen the cylinder block drain plug and then drain the
coolant completely.
Installation Notice
Tightening Torque 30 Nm
Notice
Replace the seal before installation of the drain plug.
8. Remove the cooling fan shroud.
9. Disconnect the each hose from radiator.

M162 ENGINE MECHANICAL 1B1-11
12. Discharge the refrigerant from A/C system, and disconnect
the discharge pipe and suction pipe from the compressor.
14. Remove the fuel feed and return line.
Notice
Before removing the fuel lines, release the pressure in the
fuel system.
Installation Notice 13. Remove the acceleration control cable and automatic
transmission pressure cable. 11. Remove the hydraulic pipe of power steering.
Notice
Completely drain the oil.
Tightening Torque 21 - 25 Nm

1B1-14 M162 ENGINE MECHANICAL
Tightening Torque 30 Nm 29. Remove the exhaust manifold and exhaust pipe.
Installation Notice
25. Separate the vacuum hose for brake booster.
26. Separate the other vacuum hoses.
27. Remove the propeller shaft from the front axle.
Installation Notice
28. By rotating the crankshaft from the front of engine, remove
the 6 torque converter mounting bolts from the engine
ring gear plate.
Tightening Torque 81 - 89 Nm

M162 ENGINE MECHANICAL 1B1-15
30. Remove the transmission mounting bolts and separate
the transmission from the engine.
Installation Notice
Tightening Torque 65 Nm
31. Remove the bolts for engine mounting bracket.
Installation Notice
Tightening Torque 50 - 75 Nm
32. Hook the chain to the bracket of engine and by using a
hoist or crane, carefully separate the engine assembly
from the vehicle.
33. Installation should follow the removal procedure in the
reverse order.

1B1-18 M162 ENGINE MECHANICAL
ALTERNATOR
1 Nut (M8).........................................22.5-27.5 Nm
2 Bolt (M8 x 30, 3 pieces).................22.5-27.5 Nm
3 Bolt (M8 x 40, 1 piece)...................22.5-27.5 Nm
Removal & Installation Procedure
1. Remove the drive belt.
2. Remove the alternator.
3. Unscrew the alternator carrier bolts and remove the carrier.
Installation Notice4 Bolt (M8 x 70, 1 piece)...................22.5-27.5 Nm
5 Bolt (M8 x 75, 1 piece)...................22.5-27.5 Nm
Tightening Torque 10 - 15 Nm
4. Installation should follow the removal procedure in the
reverse order.

1B1-20 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Remove the belt pulley.
Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump
and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump.
Installation Notice Notice
Pull the tensioning pulley clockwise as shown in the figure.
4. Remove the compressor after disconnecting the wiring
connector and refrigerant pipe of A/C compressor.
Notice
Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-21
5. Disconnect the vent hose from the A/C bracket.
6. Unscrew all the mounting bolts (arrows) and remove the
A/C bracket and the gasket.
Installation Notice
7. Clean the sealing surface.
8. Replace the gasket with new one.
9. Installation should follow the removal procedure in the
reverse order.
10. Check the oil leakage by operating the engine after
installation.
Tightening Torque 22.5 - 27.5 Nm

1B1-24 M162 ENGINE MECHANICAL
1 Upper Nut
2 Hydraulic Installor.................62-93 Nm
3 Lower Nut.............................28-47 Nm
Removal and Installation Procedure
1. Unscrew the upper nut(1) on engine mounting and remove
the engine.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 62 - 93 Nm
2. Unscrew the lower nut(3) and remove the hydraulic engine
mounting insulator.
Installation Notice
Tightening Torque 28 - 47 Nm
Notice
If the insulator is spotted with oil, replace the hydraulic
insulator assembly.