1998 SSANGYONG MUSSO torque

1F2-66 M161 ENGINE CONTROLS
1 Crankshaft Position Sensor (connector)
2 Bolt (M6 X 14)........................................ 9-11 Nm
CRANKSHAFT POSITION SENSOR
Removal & Installation Procedure
1. Disconnect the wiring connector at the crankshaft position
sensor.
2. Unscrew the bolt (2) and remove the crankshaft position
sensor unit (3).
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.3 Sensor Unit
Tightening Torque 9 - 11 Nm

1F2-68 M161 ENGINE CONTROLS
CAMSHAFT POSITION SENSOR
1 Bolt (M6 X 14)......................................... 9-11Nm
2 Camshaft Position Sensor
Removal & Installation Procedure
1. Disconnect the wiring connector from the camshaft position
sensor.
2. Unscrew the bolt (2) and remove the camshaft position
sensor.
Installation Notice3 Shim
5 O-ring
Tightening Torque 9 - 11 Nm
3. Check the clearance and replace the shim if necessary.
4. Check the O-ring for damage and replace it if necessary.
5. Installation should follow the removal procedure in the
reverse order.

M161 ENGINE CONTROLS 1F2-75
KNOCK SENSOR
Functions
Vibration of the engine block is transmitted to the sensor and
transferred to the ECU in the form of an alternating voltage
signal via a shielded cable. The knock sensor is fastened to
the engine block to recognize knocking in all cylinders. The
ECU compares the signal and the retards firing point.
Removal & Installation Procedure
1. Disconnect the knock sensor connector from the intake
manifold bracket.
2. Unscrew the mounting bolt (M8 X 28) from the knock sensor
installed on the cylinder block and remove the knocking
sensor.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 22.5 - 27.5 Nm

1F2-76 M161 ENGINE CONTROLS
COOLANT TEMPERATURE SENSOR
1 Artificial Resin Housing
2 Metal Housing
3 NTC (negative temperature coefficient) Resistor
Removal & Installation Procedure
1. Remove the pressure by opening the pressure cap in the
coolant subtank.
2. Disconnect the connector and remove the coolant
temperature sensor.
Installation Notice
Replace the seals with new one.
3. Installation should follow the removal procedure in the
reverse order.
4. Check for leaks at each connections after starting the engine.4 Connector
5 Coolant Temperature Sensor
Tightening Torque 18 - 22 Nm

M161 ENGINE CONTROLS 1F2-79
ACCELERATOR PEDAL MODULE
1 Accelerator pedal
2 Accelerator pedal Sensor
3 Bolts (2 Pieces).......................................4-8 Nm
Removal and Installation Procedure
1. Disconnect the 6-pin connector(arrow).
2. Unscrew the 2 bolts (3) / 1 nut (6) and remove the pedal
and sensor assembly.
Installatoin Notice
Tightining Torque 4 - 8 Nm
2. Installation should follow the removal procedure in the
reverse order.4 6-Pin Connector
5 Kick down Switch
6 Nut (1 piece)............................................4-8 Nm

1F3-14 OM600 ENGINE CONTROLS
Removal & Installation Procedure
1. Remove the vacuum line (3, 4).
2. Remove the bolts (1) evenly.
Notice
If necessary, rotate the engine until the pressure on the
tappet of the vacuum pump is released.
3. Remove the vacuum pump (2).
4. Install the vacuum pump (2).
Tightening Torque 10 Nm
Notice
Clean the gasket residues of sealing surface of vacuum
pump and replace the gasket(5).
5. Connect the vacuum line (3, 4).

1F3-26 OM600 ENGINE CONTROLS
Tools Required
001 589 65 09 00 Serration Wrench
Removal & Installation Procedure
1. Remove the plastic clip from the injection pipe
2. Remove the fuel return hose.
3. Disconnect the injection pipes from the injection nozzles and
push them to the side.
4. Remove the fuel injection nozzle.
Serration Wrench 001 589 65 09 00
Notice
Replace the washers.
5. Installation should follow the removal procedure in the
reverse order.
Notice
Pay attention to the installation position of new nozzle washer
and tightening torque

1F3-28 OM600 ENGINE CONTROLS
Tools Required
001 589 65 09 00 Socket Wrench Insert
000 589 00 68 00 Cleaning Set
Repair Procedure
1. Clamp the nozzle holder (1) in a vice and remove the nozzle
tensioning nut (8).
Notice
Use protective jaws for clamping.
2. Disassemble the fuel injection nozzle.
Socket Wrench Insert 001 589 65 09 00
3. Clean the nozzle needle (6) and nozzle body (7) with an
abradant.
4. Clean the nozzle seat with cleaning cutter.
Cleaning Set 000 589 00 68 00
5. Immerse nozzle needle (6) and nozzle body (7) in filtered
diesel fuel. When the nozzle body is held vertical, the weight
of the nozzle needle must cause it to slide down toward the
nozzle needle seat.
6. Assemble the injection nozzle so that the tip of the thrust
(4) pin is facing toward the nozzle holder.
Tightening Torque 80 Nm
Notice
Nozzle needle (6) and nozzle body (7) should always be
replaced as a pair.