1998 SSANGYONG MUSSO service

SECTION 9Q
ROOF
TABLE OF CONTENTS
Schematic and Routing Diagrams . . . . . . . . 9Q-2
Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Q-2
Maintenance and Repair . . . . . . . . . . . . . . . 9Q-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9Q-3
Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Q-3

ROOF 9Q-3
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
SUN ROOF
1 Inner Sliding Sun Roof Assembly
2 Sun Roof Body Mounting Bracket
3 Drain Hose Rear Grommet
4 Sun Roof Motor Spanner
5 Mounting Clip6 Mounting Bracket
7 Mounting Bracket Assembly
8 Sun Roof Mounting Bracket
11 Sun Roof Module Assembly

SECTION 9R
BODY FRONT END
TABLE OF CONTENTS
Maintenance and Repair . . . . . . . . . . . . . . . 9R-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9R-2Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9R-2
Fender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9R-5

9R-2 BODY FRONT END
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
HOOD
1 Hood
2 Sping3 Hood Hinge Assembly
4 Bolt

SECTION 9T
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 9T-1
REKES Specifications . . . . . . . . . . . . . . . . . . . 9T-1
Schematic and Routing Diagrams . . . . . . . . 9T-2
REKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-3
SPECIFICATIONS
REKES SPECIFICATIONS
Diagnosis Test . . . . . . . . . . . . . . . . . . . . . . . . 9T-3
Maintenance and Repair . . . . . . . . . . . . . . . 9T-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9T-5
REKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-5
Transmitter
Description
DC 3V
-10°C - 60°C
Changeable Coin Type LITHIUM Battery
(CR2032)
Above 2 years (10 times/day) Application
Rated Voltage
Rated Range of Operating Temperature
Model
Durability
Description
DC 12V
DC 8V - 16V
-30°C - +80°C
Above 5M W
Maximum 3mA Application
Rated Voltage
Rated Range of Operating Voltage
Rated Range of Operating Temperature
Insulating Resistance
Arm Current
Receiver

REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM 9T-3
DIAGNOSIS TEST
Introduction
Using the service connector, possible defects in power section,
input·output section of internal STICS unit can be detected and
each normal status and defect mode can be checked.
Diagnosis Method
1. Use buzzer for diagnosis check status output.
2. Following function outputs should not act when diagnosis
switch is ON (STICS in the diagnosis socket box:connection
of No. 7 and ground No.1).
- Tail lamp ON warning (buzzer output stop, door lock/
unlock output stop)
- Seat belt warning (chime bell output stop)
- Key reminder warning (chime bell output stop, door lock/
unlock output stop)
- Central door lock (door lock/unlock output stop)
3. Functions in No. 2 should be restored when diagnosis switch
is OFF.
4. Checked output should be made once while the diagnosis
switch is ON.
5. When inputs are made by operating each different switches
more than 2 continuously, make output according to input
order (buzzer ON) and turn off the buzzer for 1 second and
than make other remaining outputs for input switch.
DIAGNOSIS

REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM 9T-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
REKES
1 REKES Receiver
2 Antenna3 Bolt
4 Wiring Connector (6P)

9T-6 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
Input Memory
lWhen the REKES transmitter is lost
1. Connect the battery terminal No.3 and REKES terminal No.4
which are on the diagnosis socket in engine room with service
lead wire.
2. Push the lock or unlock button on the REKES transmitter.
3. Input Memory and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
lWhen the transmitter is faulty
1. Replace the REKES transmitter with a new one and connect
the wiring connector.
2. Set the input switch of the REKES receiver onto the No.1 or
No.2 position and push the lock or unlock button on the
REKES transmitter.
3. Set the input switch of the REKES receiver onto the central
position and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
1 REKES Transmitter
2 Input Switch of the REKES Receive
3 REKES Switch