1998 SSANGYONG MUSSO wheel bolt torque

M162 ENGINE CONTROLS 1F1-65
1 Crankshaft Position Sensor
2 Bolt (M6 X 14)........................................ 9 -11Nm
CRANKSHAFT POSITION SENSOR
Removal & Installation Procedure
1. Disconnect the wiring connector at the crankshaft position
sensor.
2. Unscrew the bolt and remove the crankshaft position sensor
unit.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.3 Segment
4 Flywheel
Tightening Torque 9 -11Nm

FRONT SUSPENSION 2C-7
Removal & Installation Procedure
1. Remove the fixing nuts and bolts of the shock absorber
and lower arm connection.
Installation Notice
2. Remove the connecting nuts of the stabilizer bar link to the
lower arm.
Installation Notice
3. Turn the height control bolt until the distance between the
end of the height control bolt end piece and the bolt end
becomes 0-5 mm.
Installation Notice
Install the torsion bar spring and adjust the distance between
the end of the height control bolt and piece end the bolt
end to be 50-55 mm. Adjust the vehicle height.
Tightening Torque 60 - 80 Nm
Tightening Torque 16 - 22 Nm
4. Remove the torque arm fixing nuts and bolts and then
withdraw the torsion bar spring.
Installation Notice
M10
M12Tightening Torque40 - 60 Nm
60 - 80 Nm
5. Installation should follow the removal precedure in the
reverse order.
6. Check and adjust the wheel alignment.

TIRES AND WHEELS 2E-7
lTo correct unbalance, install equal weights 180° opposite
each other, one on the inside of the wheel and one on
the outside, at the point of unbalance.
lBalance Weight
6. Cautions for installation and removal.
lClean the mounting surfaces of hub and wheel.
lDo not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
lUsing a jack, lift up the tire about 3cm from the ground.
lTighten nuts in a criss-cross pattern 2-3 times.
10g
0.4oz20g
0.7oz30g
1.10oz40g
1.40oz50g
1.80oz60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

FRONT DRIVE AXLE 3A-9
Removal & Installation Procedure
1. Remove the tire.
Installation Notice
Steel Wheel
Aluminum WheelTightening Torque80 - 120 Nm
110 - 130 Nm
2. Remove the autolocking hub vacuum hose.
3. With ABS
Remove the wheel speed sensor from the steering knuckle.
Installation Notice
4. Remove the mounting bolts and pull off the caliper assembly.
Installation Notice
Tightening Torque 6 - 8 Nm
Hose Bolt
Mounting BoltTightening Torque25 - 35 Nm
85 - 105 Nm
Notice
Be careful not to damage the brake hose.

REAR DRIVE AXLE 3D-7
Removal & Installation Procedure
1. Remove the tire.
Installation Notice
2. Release the parking brake.Steel Wheel
Aluminum Wheel
Tightening Torque
3. Remove the bolts and the brake caliper.
Installation Notice
Be careful not to damage the brake hose.
Tightening Torque 85 - 100 Nm
4. Remove the brake disc.
Notice
To remove the disc, install the bolts (M8 x 1.25) into the
service hole and uniformly tighten the bolts.
5. Disconnect the parking brake cable.
80 - 120 Nm
110 - 130 Nm

FRONT DISC BRAKES 4D-3
Removal & Installation Procedure
1. MANDO Brake
Tightening Torque 25 - 35 Nm
2. PBR Brake
Remove the eye-hose bolt and disconnect the hose.
Installation Notice
Tightening Torque 15 - 18 Nm
3. Remove the wheel speed sensor (for ABS vehicies).
Installation Notice
Tightening Torque 6 - 8 Nm
4. Remove the mounting bolts and then caliper assembly.
Installation Notice
Tightening Torque 85 - 105 Nm
Remove the hose mounting nut and disconnect the hose.
Installation Notice

REAR DISC BRAKES 4E-3
Tightening Torque 15 - 18 Nm
Tightening Torque 85 - 105 Nm
Removal & Installation Procedure
1. Remove the eye-hose bolt and disconnect the hose.
Installation Notice
2. Unscrew the mounting bolts and remove the brake caliper
assembly.
Installation Notice
3. Pull out the brake pads. Replace pads if necessary.
Notice
Always change the all pads on one wheel at a time.
4. Installation should follow the removal precedure in the
reverse order.
5. Bleed the air from the system.

5C-10 CLUTCH
Removal & Installation Procedure
1. Remove the starter motor. Install the special tool to the
flywheel through the starter motor mounting holes.
Tightening Torque
47 Nm
Engine Lock 602 589 00 40 00
2. Unscren the release cylinder mounting bolts and remove
the release cylinder.
Installation Notice
3. Unscrew the clutch housing bolts and remove the clutch
housing, release fork and release bearing.
Installation Notice
4. Insert the centering pin into the clutch spline.
Loosen the clutch cover bolts 1/2 turn in crisscross sequence
until the spring tension is released.
Notice
Do not remove the bolts at a time, or clutchcover can be
damaged or deformed.
Centering Pin 661 589 00 15 00
Tightening Torque
30 - 40 Nm