1998 SSANGYONG MUSSO fuel

1F3-40 OM600 ENGINE CONTROLS
Start of Delivery (RIV)
Idle Speed (Connection Diagram for Testers With Adapter)
1 Fuel Injection Pump
2 Rl Sensor
3 Digital Tester4 TDC Pulse Sender Unit
5 Battery
6 Rl Pulse Generator
Service Data
ATDC 14° - 16°
OM661LA : 720 - 820 rpm, OM662LA : 750 - 850 rpm

1F3-42 OM600 ENGINE CONTROLS
After Testing
Preceding Work : Start of delivery test
Position Sensor (RIV method)
1 Adjusting Screw
2 Bolt............................................................23Nm
3 Fuel Injection Pump4 Bolt............................................................23Nm
5 Scale.......... Rl start of delivery = 14° - 16° ATDC

1F3-46 OM600 ENGINE CONTROLS
Tools Required
000 589 77 03 00 Box Wrench Insert
601 589 00 08 00 Flange
601 589 05 21 00 Locking Screw
601 589 05 14 00 Assembly CageRemoval
FUEL INJECTION PUMP
Preceding Work : Removal of vacuum pump
Removal of air cleaner housing
Removal of intake manifold
18 Chain Tensioner.........................................80Nm
1 9 Seal....................................................... Replace
20 Bolt(Left-Hand Thread)..............................46Nm
21 Washer
2 2 Bolt............................................................23Nm
2 3 Seal....................................................... Replace24 Oil Pan
25 Fuel Injection Pump
2 6 Seal....................................................... Replace
27 Screw Plug.................................................30Nm
28 Square Nut

OM600 ENGINE CONTROLS 1F3-47
2. Remove the connecting rod (9).
3. Disconnect the vacuum lines (13, 14).
4. Remove the accelerator control damper (10).
(Manual transmission vehicle)
5. Remove the suction line (16) and pressure line (4).
6. Remove the banjo bolt (1) and then remove the seal (2)
and fuel line (3).
7. Remove the plastic clip (8) on the injection line.
Removal Procedure
1. Position then no.1 cylinder at 15° ATDC.
Notice
Do not rotate the engine in opposition direction of engine
rotation.
8. Disconnect the injection lines (15) from the injection pump
(25).
9. Remove the banjo bolt (1) and then remove the seal (7)
and return line (5).

1F3-48 OM600 ENGINE CONTROLS
10. Install the assembly cage (29) and remove the bolt (20)
and pull off the washer (21).
Notice
Be careful that the bolt (20) is left hand thread.
Assembly Cage 601 589 05 14 00
11. Remove the chain tensioner (18) and seal (19).
12. Remove the bolt (12) and pull off the washer (11).
13. Remove the bolt (22) and pull off the square nut (28).
14. Pull out the fuel injection pump (25) and seal (23).

1F3-50 OM600 ENGINE CONTROLS
10. Connect the fuel pipes
Notice
Replace the seal.
Box Wrench Insert 000 589 77 03 00
Return Line
Fuel Injection Line
Fuel feed Line
Suction and Pressure Line46 Nm
18 Nm
13 Nm
13 Nm
5. Coat the new seal (23) with engine oil and install it.
6. Insert the fuel injection pump (25) and tighten the bolts
(22).
7. Remove the locking screw (32).
Tightening Torque 23 Nm
8. Tighten the bolt(12).
9. Insert the washer (21) and tighten the bolts (20) and then
remove the assembly cage (29).
Tightening Torque 23 Nm
Tightening Torque 46 Nm

M162 ENGINE INTAKE & EXHAUST 1G1-5
INTAKE MANIFOLD
Preceding Work : Removal of fuel distributor and injection valve
1 Bolt (M6 X 40, 4 pieces)......................... 9-11 Nm
2 Softcap
3 Resonance Flap
4 Gasket ................................................... Replace
5 Upper Intake Manifold
6 Bolt (M8 x 50, 9 pieces).................22.5-27.5 Nm
7 Gasket ................................................... Replace
8 Blow-by Hose
9 Blow-by Hose
1 0 Clamp
11 Blow-by Nipple
12 Inlet Air Housing13 Bolt (M6 x 40, 4 pieces)......................... 9-11 Nm
14 Throttle Body - Electric
15 Gasket ................................................... Replace
16 Lower Intake Manifold.........................................
17 Bolt (M8 x 40, 4 pieces).................22.5-27.5 Nm
1 8 Nipple.................................................... Replace
19 Seal Ring
20 Connection House
2 1 Clamp
22 Noise Damper Assembly
23 Tapping Screw

M161 ENGINE INTAKE & EXHAUST 1G2-7
INTAKE MANIFOLD
Preceding Work : Removal of intake air duce
Removal of fuel distributor and injector
1 Bolt (M6 X 40, 6 pieces).................22.5-27.5 Nm
2 Intake Manifold
3 Gasket (2 pieces).................................. Replace
4 Bolt (M8 X 40, 3 pieces).................22.5-27.5 Nm5 Idle Regulator
6 Intermediate Flange
7 Bolt (M6 X 35, 4 pieces)......................... 9-11 Nm
8 Connection Piece With Seal Ring........36-44 Nm