1998 SSANGYONG MUSSO sensor

MASTER CYLINDER 4B-3
Removal & Installation Procedure
1. Remove the oil level sensor connector.
2. Remove the tube from the master cylinder.
Installation Notice
Notice
lBe careful not to drop the oil when removing the tube.
lIf the oil is dropped, promptly sweep up.
3. Remove the booster vacuum hose.
Notice
lConnect fully to the end of vacuum hose when installing.
4. Loosen the nut of master cylinder.
Installation Notice
5. Remove the clevis pin and disconnect the pedal and brake
booster push rod.
Notice
lInstall in the upper hole when PBR brake.
lConnect the snap pin in the hole of clevis pin fully.
lApply the grease around the hole of clevis pin.
Tightening Torque 14 - 22 Nm
Tightening Torque 15 - 19 Nm

4C-2 POWER BOOSTER
1 Nut .......................................................14-22 Nm
2 Washer
3 Master Cylinder Assembly
4 Oil Level Sensor
5 Check Valve
6 Booster
7 Clevis Pin
8 Snap Pin
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
BOOSTER AND BRAKE MASTER CYLINDER
9 Seal
10 Spacer
11 Nut .........................................................8-18 Nm
12 Front Tube (LH)
13 Front Tube (RH)
14 Rear Tube
15 1st Tube (Primary)
16 2nd Tube (Secondary)
MANDO
PBR

POWER BOOSTER 4C-3
Removal & Installation Procedure
1. Remove the oil level sensor connector.
2. Remove the tube from the master cylinder.
Installation Notice
Notice
lBe careful not to drop the oil when removing the tube.
lIf the oil is dropped, promptly sweep up.
3. Remove the booster vacuum hose.
Notice
lConnect fully to the end of vacuum hose when installing.
4. Loosen the nut of master cylinder.
Installation Notice
5. Remove the clevis pin and disconnect the pedal and brake
booster push rod.
Notice
lInstall in the upper hole when PBR brake.
lConnect the snap pin in the hole of clevis pin fully.
lApply the grease around the hole of clevis pin.
Tightening Torque 14 - 22 Nm
Tightening Torque 15 - 19 Nm

FRONT DISC BRAKES 4D-3
Removal & Installation Procedure
1. MANDO Brake
Tightening Torque 25 - 35 Nm
2. PBR Brake
Remove the eye-hose bolt and disconnect the hose.
Installation Notice
Tightening Torque 15 - 18 Nm
3. Remove the wheel speed sensor (for ABS vehicies).
Installation Notice
Tightening Torque 6 - 8 Nm
4. Remove the mounting bolts and then caliper assembly.
Installation Notice
Tightening Torque 85 - 105 Nm
Remove the hose mounting nut and disconnect the hose.
Installation Notice

Front
Rear
Front
Rear
SECTION 4F
ANTILOCK BRAKE SYSTEM
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Model
ECUNumber of Pins
Operating Temperature
Motor Operating Current
Solenoid Coil Resistance
External Resistance
Air Gap
Number of teethDescription
ABS 5.3
31
-40 ~ +120°C
Below MAX 40A
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52ABS/ABD 5.3
83
-40 ~ +85°C
Below MAX 45A
8.04 - 9.04W except AV,
HSV 4.04 - 4.54W
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52 Hydraulic System
Wheel Speed Sensor
Impulse Ring
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4F-1
General Specifications . . . . . . . . . . . . . . . . . . 4F-1
Schematic and Routing Diagrams . . . . . . . . 4F-2
ABS 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-2
ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-3
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-4
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-5
Component Locator . . . . . . . . . . . . . . . . . . . 4F-6
ABS, ABS/ABD . . . . . . . . . . . . . . . . . . . . . . . . 4F-6
ABD System Description . . . . . . . . . . . . . . . 4F-7Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . 4F-11
Defect Codes . . . . . . . . . . . . . . . . . . . . . . . . 4F-13
Maintenance and Repair . . . . . . . . . . . . . . 4F-19
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 4F-19
Wheel Speed Sensor . . . . . . . . . . . . . . . . . . 4F-19
Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . 4F-21
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-21
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . 4F-24

4F-6 ANTILOCK BRAKE SYSTEM
ABS,ABS/ABD
COMPONENT LOCATOR
1 ABS Hydraulic Unit
2 ABS/ABD Hydraulic Unit
3 Diagnosis Socket
4 Front Wheel Speed Sensor
5 Front Impulse Ring6 Rear Wheel Speed Sensor
7 Rear Impulse Ring
8 ABS Warning Indicator Light
9 TCS Indicator Light
1 0 ABS/ABD ECU

ANTILOCK BRAKE SYSTEM 4F-13
DEFECT CODES
Description
-
Replace the ECU
lCheck resistance of the wheel speed sensor :
1.280KW - 1.920KW
lCheck wire for ground and open.
lReplace the sensor.
lCheck resistance of the wheel speed sensor :
1.280KW - 1.920KW
lCheck wire for ground and open.
lReplace the sensor.
lCheck resistance of the wheel speed sensor :
1.280KW - 1.920KW
lCheck wire for ground and open.
lReplace the sensor.
lCheck resistance of the wheel speed sensor :
1.280KW - 1.920KW
lCheck wire for ground and open.
lReplace the sensor.
lCheck wire for ground and open.
lCheck connection of the wheel speed sensor connec-
tor and ECU side connector.
lMeasure air gap between wheel teeth and wheel speed
sensor and check installation of wheel tooth.
(Standard air gap : 0.35 - 1.60 mm)
lCheck output voltage of the sensor by rotating the
wheel 1/2 - 1 revolution per second and shaking sen-
sor wire.
- When measured by multi - meter (AC) :
output voltage > 70 mV
- When measured in oscilloscope :
output voltage ³ 120 mV/P-P
lReplace the sensor.
lCheck wire for ground and open.
lCheck connection of the wheel speed sensor. con-
nector and ECU side connector.
lMeasure the air gap between wheel teeth and wheel
speed sensor and check installation of wheel tooth.
(Standard air gap : 0.35 - 1.60 mm)
lCheck output voltage of the sensor by rotating the
wheel 1/2 - 1 revolution per second and shaking sen-
sor wire. Defect Code
01
02
03
04
05
06
07
08Application
Normal
Defective ECU
Front/left Wheel Speed
Sensor (Wire)
Front/right Wheel Speed
Sensor (Wire)
Rear/left Wheel Speed
Sensor (Wire)
Rear/right Wheel Speed
Sensor (Wire)
Front/left Wheel Speed
Sensor (Signal)
Front/right Wheel Speed
Sensor (Signal)

4F-14 ANTILOCK BRAKE SYSTEM
Description
- When measured by multi - meter (AC) :
output voltage > 70 mV
- When measured in oscilloscope :
output voltage ³ 120 mV/P-P
lReplace the sensor.
lCheck wire for ground and open.
lCheck connection of the wheel speed sensor con-
nector and ECU side connector.
(Standard air gap : 0.15 - 1.20 mm)
lCheck output voltage of the sensor by rotating the
wheel 1/2 - 1 revolution per second and shaking sen-
sor wire.
- When measured by multi - meter (AC) :
output voltage > 70 mV
- When measured in oscilloscope :
output voltage ³ 120 mV/P-P
lReplace the sensor.
lCheck wire for ground and open.
lCheck connection of the wheel speed sensor con-
nector and ECU side connector.
lMeasure air gap between wheel teeth and wheel
speed sensor and check installation of wheel tooth.
(Standard air gap : 0.15 - 1.20 mm)
lCheck output voltage of the sensor by rotating the
wheel 1/2 - 1 revolution per second and shaking sen-
sor wire.
- When measured by multi - meter (AC) :
output voltage > 70 mV
- When measured in oscilloscope :
output voltage ³ 120 mV/P-P
lReplace the sensor.
lCheck number of teeth on the wheel rotor and its
condition.
- Number of teeth : 52
lCheck valve relay voltage.
lCheck connection of connector and terminals in the
ECU and hydraulic modulator.
lCheck ground.
lCheck terminals for open or short.
(When connector is removed)
lReplace the hydraulic modulator. Defect Code
09
10
11
12Application
Rear/left Wheel Speed
Sensor (Signal)
Rear/right Wheel Speed
Sensor (Signal)
Wheel Rotor
Valve Relay