1998 PONTIAC FIREBIRD light

lhrn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn
or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will retum automatically.
An arrow on the instrument
panel will flash in the
direction of the
turn or
1 lane change.
To signal a lane change, just raise or lower the lever
until
the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrows don’t
flash but just stay on,
a signal bulb may be burned out
and other drivers won’t see your
turn signal. If
a bulb is burned out, replace it
to help avoid an
accident. If the arrows don’t
go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
B&kers” in the Index).
Headlamp High/Low Beam
When the high-beams are
on, this light on the
instrument panel also will
be on.
To change the headlamps from low beam to high or
from high beam to low, pull the turn signal lever all the
way toward you. Then release it.
2-47

Windshield Wipers
You control the windshield wipers by turning the band
with the wiper symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then
let go. The wipers will
stop after one cycle.
If you want more cycles, hold the
band on
MIST longer. You
can set the wiper speed for a long or short delay
between wipes.
This can be very useful in light rain or
snow.
Turn the band to choose the delay time. The
closer to
LO, the shorter the delay.
For steady wiping at low speed,
turn the band away
from
you to the LO position. For high-speed wiping,
turn the band further, to HI. To stop the wipers, move
the band to OFF.
Damaged wiper blades may prevent you from seeing
well
enough to drive safely. To avoid damage, be sure to
clear ice and snow from the wiper blades before using
them. If they’re frozen to the windshield, carefully
loosen or thaw them. If your blades do become
damaged, get new blades
or blade inserts.
Heavy snow or ice can overload your wipers.
A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
2-48

Ending Out of Cruise Control
There are several ways to turn off the cruise control:
Step lightly on the brake pedal or push the clutch
pedal, if you have a manual transmission; or
Move the cruise switch to OFF.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control
set speed memory is erased.
Exterior Lamps
-.
The main lamp control is a knob that works these lamps:
Headlamps
Taillamps
Parking Lamps
License Lamps
0 Sidemarker Lamps
0 Instrument Panel Lights
# , This setting turns on your headlamps and other
operating lamps.
pg This setting turns on your parking lamps and other
operating lamps without your headlamps.
Turn the
knob to OFF to turn off the lamps.
-‘a-
Headlamps On Reminder
If you turn the ignition off and leave the lamps on, you
will hear
a chime lasting up to five seconds. If the lamps
are still on when
you open the driver’s door, the chime
will sound
again.
2-52

Headlamp Doors Daytime Running Lamps
The headlamp doors are designed to open when you turn
the headlamps
on and close when
you turn the
headlamps off. The headlamp doors can
be opened
without turning on the headlamps by turning the
headlamps on, then turning the switch back to the
parking lamps position.
The headlamp doors should
be open when driving in
icy or snowy conditions to prevent the doors from
freezing closed, and when washing the vehicle to help
clean the headlamps.
You can open the headlamp doors manually:
1. Open the hood.
2. Remove the plastic cover from the retractor
motor knob.
3. Turn the retractor motor knob counterclockwise until
the headlamp door
is fully open. The knob will get
harder to turn when the headlamp door
is all the
way up.
4. Replace the plastic cover on the retractor motor knob. Daytime Running Lamps (DRL) can make
it easier for
others to
see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
For Canadian vehicles, a light sensor on top of the
instrument panel automatically turns the headlamps on,
so be sure it isn’t covered.
The DRL system will make your front turn signal lamps
come on when:
0 The ignition is on,
the headlamp switch is OFF,
0 the parking brake is released and
0 it is bright enough outside (on Canadian vehicles).
To manually close the headlamp doors, turn the lamps
off and turn the retractor motor knob clockwise. If the
headlamp doors aren’t working properly, see your dealer
for help.
2-53

When the DlU are on, only your front turn signal
lamps will be on. The taillamps, sidemarker and other
lamps won’t be on. Your instrument panel won’t be lit
up either.
For Canadian vehicles, when it’s dark enough outside,
your front turn signal lamps will go out and your
headlamps will come on. The other lamps that come on
with your headlamps will also come on. When it’s bright
enough outside, the regular lamps will go
off, and your
front turn signal lamps will come on.
On a non-Canadian vehicle, the
DRL have to be turned
on manually when you need them. On Canadian and
domestic vehicles, when the headlamps are turned on,
the front
turn signal lamps will go out. When you use
your turn signals, the front turn signal lamp and the
taillamp on the desired side will flash.
As with any vehicle, you should turn on the regular
headlamp system when
you need it.
Fog Lamps
Use your fog lamps for better vision in foggy or misty
conditions. Your parking lamps must be on or your fog
lamps won’t work.
To turn the fog lamps on,
push the right side of the
fog lamp switch.
Push the
left side of the switch to
turn the fog lamps
off. A
light on the switch will
come on when the fog
lamps are on.
Fog lamps will
go off whenever your high-beam
headlamps come on. When the high beams go
off, the
fog lamps will come on again.
If your vehicle is equipped with the Content
Theft-Deterrent System
and your fog lamp switch is on,
the fog lamps may flash to indicate operation of the
Content Theft-Deterrent System. See “Content
Theft-Deterrent System” in the Index.

Interior Lamps
Instrument Panel Brightness Control
This switch controls the brightness of your
instrument panel lights. Turn the switch to brighten or
dim the lights.
If you turn the switch all the way up,
your courtesy lamps will come on.
Courtesy Lamps
When either door is opened, several interior lamps go
on. These lamps are courtesy lamps. They make it easier
for you to enter and leave your vehicle.
Courtesy lamps include the dome lamp and other lamps
throughout
the interior of your vehicle.
To prevent battery rundown, your interior lamps will be
disabled about
10 minutes after the ignition is turned to
OFF. The 10-minute timer will be restarted if you do
any of the following:
1. Turn the ignition on.
2. Open either door.
3. Press any button on your remote keyless entry
transmitter.
4. Turn the interior lamp switch from off to on.
5. Open the hatch.
Delayed Illumination
With delayed illumination, the courtesy lamps will stay
on for
25 seconds after you close the doors when
entering the vehicle. They will stay on for five seconds
after you close the doors when exiting the vehicle. The
times will be shortened if the ignition is turned
to RUN
or if the power locks are activated. To turn this feature
on or off, see “Feature Customization”
in the Index.
Exit Lighting
With exit lighting, the interior lamps will come on when
you remove the key from the ignition to help you see
while exiting the vehicle. To turn this feature on or
off,
see “Feature Customization” in the Index.
2-55

When carrying large or heavy items, it is a good idea to
open
the panel and place the items in the rear area.
I A CAUTION:
An improperly stored close-out panel could be
thrown about the vehicle during a collision
or
sudden maneuver. You or others could be
injured.
If you remove the cover, always store it
outside your vehicle. When you put it back,
always be sure that it is securely reattached.
Ashtray and Lighter
Lift up the cover to open the ashtray. To remove it, lift
up on either side of the ashtray.
If you have an automatic
transmission, the ashtray is near the front
of your
console.
If you have a manual transmission, the ashtray
is near your cupholder.
NOTICE:
Don’t put papers and other things that burn into
your ashtray. If you do, cigarettes or other
smoking materials could set them on fire,
causing damage.
To use the lighter, push it in all the way and let go.
When it’s ready, it will
pop back by itself.
2-60

NOTICE:
Don’t hold a cigarette lighter in with your hand while it is heating.
If you do, it won’t be able to
back away from the heating element when it’s
ready. That can make it overheat, damaging the
lighter and the heating element.
If you plug accessories into your cigarette lighter, such as heating devices
or air compressors, these accessories
should have a rated current
of less than 15 amps.
Exceeding this limit will result in a blown fuse.
Sun Visors
I
To block out glare, you can swing down the visors. You
can
also swing them to the side.
Visor Vanity Mirror
Pull down the sun visor and lift the cover to expose the
vanity mirror.
2-61