1998 PONTIAC FIREBIRD light

This system is called OBD I1 (On-Board
Diagnostics-Second Generation) and
is intended to
assure that emissions
are at acceptable levels for the life
of the vehicle, helping to produce a cleaner
environment. The
SERVICE ENGINE SOON light
comes on to indicate that there is a problem and service
is required. Malfunctions often will be indicated by the
system before any problem is apparent.
This may
prevent more serious damage to your vehicle.
This
system is also designed to assist your service technician
in correctly diagnosing any malfunction.
NOTICE:
If you keep driving your vehicle with this light
on, after a while,
your emission controls may not
work as well, your fuel economy
may not be as
good and your engine may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running.
If the light doesn’t come on, have it repaired.
This light will also come on during a malfunction in one
of two ways:
0 Light Flashing -- A misfire condition has been
detected. A misfiie increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service may be required.
Light On Steady -- An emission control system
malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.
2-86

If the Light Is Flashing If the Light Is On Steady
The following may prevent more serious damage to
your vehicle:
Reducing vehicle speed.
Avoiding hard accelerations.
0 Avoiding steep uphill grades.
If you are towing a trailer, reduce the amount of
cargo being hauled as soon as it is possible.
If the light stops flashing and remains on steady, see “If
the Light Is On Steady” following.
If the light continues to flash, when it is safe to do
so,
stop the vehicle. Find a safe place to park your vehicle.
Turn the key
off, wait at least 10 seconds and restart the
engine.
If the light remains on steady, see “If the Light
Is On Steady” following. If the light is still flashing,
follow the previous steps, and drive the vehicle to your
dealer or qualified service center for service.
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If
so, reinstall the fuel cap, making sure to fully install
the cap. The diagnostic system can determine
if the fuel
cap has been left off
or improperly installed. A loose or
missing fuel cap will allow fuel to evaporate into the
atmosphere. A few driving trips with the cap properly
installed should turn the light off.
Did you just drive through
a deep puddle of water?
If
so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out. A few driving trips should turn the light off.
Are you low on fuel?
As your engine starts to run out of fuel, your engine may
not run as efficiently as designed since small amounts of
air
are sucked into the fuel line causing a misfire. The
system can detect this. Adding fuel should correct this
condition. Make sure to install the fuel cap properly. It
will take a few driving trips to turn the light
off.
2-87

Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel (see
“Fuel” in the Index). Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience one or more of these conditions,
change the fuel brand you use. It will require at least one
full tank of the proper fuel to turn the light off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical
problems that may have developed.
Oil Pressure Gage
\*
0
/
0 120
3800 V6 Engine 5.7L VS Engine
One of these gages may tell you there could be a
problem with
your engine oil pressure.
The engine oil pressure gage shows the engine oil pressure
in psi (pounds per square inch) in the United States, or kpa
(kilopascals)
in Canada, when the engine is running. On
the 5.7L V8 engine, oil pressure should be 20 to 80 psi
(140 to 550 Pa). On the 3800 V6 engine, the oil pressure
should be between 20 and 120 psi (140 to 827 Wa). It
may vary with engine
speed, outside temperature and oil
viscosity, but readings above the red area show the normal
operating range. Readings
in the red area tell you that the
engine is low
on oil, or that you might have some other oil
problem. See “Engine Oil” in the Index.

A CAUTION:
Don’t keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
I Low Oil Light
I NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered
by
your warranty.
LOW
OIL
Your vehicle is equipped
with an oil level monitoring
system. When you start
your engine, the warning light will come on briefly.
If
the light doesn’t come on,
have it repaired.
If the light stays on after starting your engine, your
engine oil level may be too low. You may need to add
oil.
See “Engine Oil” in the Index.
NOTICE:
The oil level monitoring system only checks the
oil level when you are starting your engine.
It
does not keep monitoring the level once your
engine
is running. Also, the oil level check only
works when the engine has been turned
off long
enough for the oil to drain back into the oil pan.
2-89

Check Gages Light
CHECK
GAGES
This warning light will
come on briefly when you
are starting the engine.
If the light comes on and stays on while you are driving,
check your gages to see
if they are in the warning areas.
Fuel Gage
Your fuel gage shows about
how much fuel is in your
tank.
The gage works only
when the ignition is
in
RUN.
When the gage pointer first indicates empty (E) you
need to get more fuel right away.
Here
are four concerns some owners have had abut the
fuel gage. All these situations are normal and do not
indicate that anything is wrong with the fuel gage.
0
0
0
0
At the gas station, the gas pump shuts off before the
gage reads full
(F).
It takes more (or less) gas to fill up than the gage
reads. For example, the gage reads
1/2 full, but it
took more (or less) than half
of the tank’s capacity to
fill it.
The gage moves
a little when you turn, stop or
speed up.
When
you turn the engine off, the gage doesn’t go
back to empty
(E).
2-90

Air Conditioning
The air conditioning system uses the same controls as
the heating system, except that the air control knob has
two extra settings, described below.
MAX: Provides maximum cooling or quick cool-down
on very hot days. This setting recirculates most
of the air
inside your vehicle. If it is used for long periods of time,
the
air may become dry. This setting directs air through
the upper
air vents.
A/C: Use for normal cooling on hot days. This
setting cools outside air and directs it through the
upper air vents.
The
air conditioner compressor operates in MAX, NC,
bi-level, blend and defrost when the outside temperature is above
freezing. When the air conditioner is on, you may
sometimes notice slight changes in your vehicle's engine
speed and power. This is normal because the system is
designed to cycle the compressor on and off to keep the
desired cooling and help fuel economy.
Cooling
The air conditioner works best if you keep your
windows closed. On very hot days, open the windows
just long enough for the hot air to escape.
1. Turn the air control knob to A/C for normal cooling.
2. Turn the temperature control knob to a
For faster cooling move
the knob to MAX.
comfortable setting.
3. Move the fan control knob to the desired speed.
3-3

Rear Window Defogger (If Equipped)
0
The rear window defogger
uses a warming grid to
remove fog from the
rear window.
Press the button to
turn on the defogger. An indicator
light
will come on to remind you that the defogger
is
on. The defogger will turn off automatically after
about
10 minutes of use. If you turn it on again, the
defogger will operate for about five minutes only.
You can turn the defogger off by pressing the
button again.
Do not attach anything like a temporary vehicle license
or
a decal across the defogger grid on the rear window.
NOTICE:
Don’t use a razor blade or something else sharp
on the inside
of the rear window. If you do, you
could cut
or damage the warming grid, and the
repairs wouldn’t be covered by your warranty.
3-5

MonsoonTM AM-FM Stereo with Cassette RECALL: Display the time with the ignition off by
Tape Player and Equalizer (If Equipped) pressing this button. When the radio is playing, press
this knob to recall the station frequency.
Included
with the Monsoon AM-FM Stereo with
Cassette Tape Player and Equalizer are 10
high
performance speakers and a powerful 8 channel
amplifier.
This feature requires power windows and
door locks. Please see your dealer for details.
Playing the Radio
POWER-VOL:
Push this knob to turn the system on
and
off. To increase volume, turn the knob to the right.
Turn it to the left to decrease volume.
Finding a Station
AM-FM: Press this button to switch between AM, FM1
and
FM2. The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations.
Push the knob back into its stored
position when you’re not using it.
SEEK: Press the up or down arrow to go to the next
higher
or lower station and stay there.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations.
You can set up to
18 stations (six
AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press AM-FM to select the band.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
SET appears on the display. Whenever you press that
numbered button, the station you set
will return.
5. Repeat the steps for each pushbutton.