1998 OPEL FRONTERA seat

EXTERIOR/INTERIOR TRIM8J–17
Luggage Side and Quarter Upper Trim Cover (Short Wheel Base)
Luggage Side, Quarter Upper Trim Cover and Associated Parts
760RW021
Legend
(1) Rear Assist Grip
(2) Quater Upper Trim Cover
(3) Seat belt adjust Shoulder Anchor Plate
(4) Front Seat Belt Anchor Bolt Cover and Anchor
Bolt
(5) Luggage Side Trim Cover
(6) Rear Seat Belt Anchor Bolt Cover and Anchor
Bolt(7) Rear End Floor Trim Cover
(8) Luggage Side Cap
(9) Speaker Grill
(10) Rear Speaker
(11) Luggage Room Light
(12) Rear Roof Trim Cover
Removal
1. Disconnect the battery ground cable.2. Remove the rear end floor trim cover.
3. Remove the luggage side cap.

8J–18EXTERIOR/INTERIOR TRIM
4. Remove the luggage side trim cover (1).
Remove the rear side fixing screws and pry the trim
cover retainers free from the body panel and the
upper trim cover.
Remove the cover by pulling the front seat belt out
of the slit on the lower side of the trim cover.
687RS002
5. Remove the luggage room light.
Remove the luggage room light lens and the fixing
screws.
Disconnect the luggage room light connector.
6. Remove the rear roof trim cover.
Pry the trim cover retainers free from the body
panel.
666RS001
7. Remove the speaker grille.
687RS003
8. Remove the rear speaker.
Remove the rear speaker fixing screws and
disconnect the connector.
9. Remove the rear assist grip (7).
Open the both side of the assist grip cover (8) and
remove two fixing screws.
743RW004

EXTERIOR/INTERIOR TRIM8J–19
10. Remove the rear seat belt anchor bolt cover (1) and
the anchor bolt (2).
755RW037
11. Remove the front seat belt anchor bolt cover (3) and
the anchor bolt (4).
760RW006
12. Remove the quarter upper trim cover.
Remove the rear side clips of the trim cover and pry
the quarter upper trim cover retainers free from the
body panel.
687RW001
13. Remove the seat belt adjust shoulder anchor plate.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0kgꞏm/29 lb ft)

8J–20EXTERIOR/INTERIOR TRIM
Center Pillar and Roof Side Trim Cover (Long Wheel Base)
Center Pillar, Roof Side Trim Cover and Associated Parts
643RW007
Legend
(1) Roof Side Trim Cover
(2) Front Pillar Trim Cover
(3) Assist Grip (Passenger Seat Side)
(4) Adjust Shoulder Anchor Assembly/Seat Belt
Anchor Plate
(5) Center Pillar Upper Trim Plate(6) Door Sill Plate (Front and Rear)
(7) Center Pillar Lower Trim Cover
(8) Front Seat Anchor Bolt Cover and Anchor Bolt
(9) Center Pillar Assist Grip
(10) Assist Grip
(11) Rear Quarter Upper Trim Cover
Removal
1. Disconnect the battery ground cable.
2. Remove the door sill plate (front and rear).
3. Remove the center pillar lower trim cover (2).
Turn up the finisher (1) and pry the trim cover
retainers free from the body panel, then slide the
trim cover downward.
643RS003

EXTERIOR/INTERIOR TRIM8J–21
4. Remove the front seat belt anchor bolt cover (3) and
the anchor bolt (4).
760RW006
5. Remove the center pillar upper trim cover (6).
Turn up the finisher (5) and pry the trim cover
retainers free from the body panel.
643RS004
6. Remove the center pillar assist grip.
7. Remove the seat belt anchor plate/adjusut shoulder
anchor assembly.8. Remove the assist grip (7).
Open the both side of the assist grip cover (8) and
remove two fixing screws.
743RW004
9. Remove the roof side trim cover (9).
Turn up the finisher (10) and pry the trim cover
retainers free from the body panel.
643RS005
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Install the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0kgꞏm/29 lb ft)

8J–22EXTERIOR/INTERIOR TRIM
Roof Side Trim Cover (Short Wheel Base)
Roof Side Trim Cover and Associated
Parts
643RW006
Legend
(1) Front Pillar Trim Cover
(2) Roof Side Trim Cover
(3) Assist Grip (Passenger Seat Side)
(4) Rear Quarter Upper Trim Cover
Removal
1. Remove the assist grip.
2. Remove the roof side trim cover (9).
Turn up the finisher (10) and pry the trim cover
retainers free from the body panel.
643RS005
Installation
To install, follow the removal steps in the reverse order.

EXTERIOR/INTERIOR TRIM8J–25
Fuel Filler Lid Opener Cable
Fuel Filler Lid Opener Cable and Associated Parts
686RW008
Legend
(1) Rear End Floor Trim Cover
(2) Fuel Filler Lid Opener Cable (LꞏWꞏB)
(3) To Lever
(4) Cable
(5) Marking
(6) Clip
(7) To Door(8) Fuel Filler Lid Opener Cable (SꞏWꞏB)
(9) Chassis Harness
(10) Center Console Assembly
(11) Fuel Filler Lid Opener
(12) Front Seat (RH)
(13) Center Pillar Lower Trim Cover
(14) Rear Door Sill Plate (RH)
(15) Luggage Side Trim Panel (RH)
Removal
1. Disconnect the battery ground cable.
2. Remove the front seat (RH).
3. Remove the rear door sill plate (RH).
4. Remove the center pillar lower trim cover.
5. Remove the rear end floor trim panel.6. Remove the luggage side trim panel (RH).Refer to the Interior Trim Panels in this section.

EXTERIOR/INTERIOR TRIM8J–37
Luggage Floor Box
Luggage Floor Box and Associated
Parts
643RS006
Legend
(1) Rear Seat
(2) Floor Carpet
(3) Luggage Floor Box
(4) Luggage Floor Box Cover
Remove
1. Fold the rear seat assembly to the front direction.
2. Remove the luggage floor box cover.
Remove the clips which connect the floor carpet
and the luggage floor box cover.
3. Remove the luggage floor box.
Installation
1. Install the luggage floor box.
2. Install the luggage floor box cover.
Rope Hook Set
Rope Hook Set and Associated Parts
676RS003
Legend
(1) Rope Hook Set
(2) Cover
(3) Luggage Floor Carpet
(4) Hook
Removal
1. Remove the rope hook set.
Open the hook cover and hook fixing bolt.
Installation
1. Install the rope hook set.
Tighten the hook fixing bolt to the specified torque.
Torque: 13 Nꞏm (1.3kgꞏm/113 lb in)