1998 OPEL FRONTERA seat

8G–24SEATS
Installation
To reassemble, follow the disassembly steps in the
reverse order, noting the following point.1. Tighten the reclining device fixing bolts to the
specified torque.
Torque: 19 Nꞏm (1.9kgꞏm/14 lb ft)
Disassembled View
755RW035
Legend
(1) Seat Back Assembly
(2) Pad & Frame Assembly
(3) Trim Cover
(4) Hinge Knob
(5) Hinge Cover
(6) Hinge Assembly
(7) Trim Cover
(8) Arm Bracket
(9) Bush
(10) Bracket
(11) Arm Bracket Cover
(12) Pad & Frame Assembly
(13) Seat Cushion Assembly(14) Board Assembly
(15) E–Ring
(16) Cam Bracket
(17) Tension Spring
(18) Leg Pipe Assembly
(19) Hing Pin
(20) Lock Cover
(21) Floor Lock Assembly
(22) Lock Cover
(23) Band Assembly
(24) Arm Bracket
(25) Free Hinge
(26) Free Hinge Bolt

SEATS8G–25
Disassembly
1. Remove the hinge knob.
Pull the knob out from hinge assembly.
2. Remove the hinge cover.
3. Remove the hinge assembly.
4. Remove the free hinge bolt.
5. Remove the seat back assembly.
6. Remove the trim cover.
Trun up the trim cover from under the seat back
while taking notice of the hog ring and wire.
755RW032
7. Remove the pad & frame assembly.
8. Remove the seat cushion assembly.
9. Remove the free hinge.
10. Remove the lock cover.
11. Remove the floor lock assembly.
12. Remove the leg cover.
13. Remove the leg pipe assembly.
Remove the E-ring and pull the hinge pin from cam
bracket.
14. Remove the cam bracket.
15. Remove the tension spring.
16. Remove the band assembly.
17. Remove the board assembly.
18. Remove trim cover.
Remove the hog ring from back side seat cushion.
Turn up the trim cover from under the seat back
while taking notice of the hog ring.
19. Remove the arm bracket.
20. Remove the arm bracket cover.
21. Remove the pad & frame assembly.
Reassembly
To reassemble, follow the disassembly steps in the
reverse order.
Rear Seat Foot Rest
Rear Seat Foot Rest and Associated Parts
676RS001
Legend
(1) Fixing Nut
(2) Front Seat(3) Rear Seat Foot Rest
(4) Foot Rest Pad

8G–26SEATS
Removal
1. Remove the foot rest pad.
676RS002
2. Remove the fixing nuts.
3. Remove the rear seat foot rest.
Installation
To install, follow the removal steps in the reverse order.
Main Data and Specifications
Torque Specifications
E10RX006

SEATS8G–27
E10RW031

8J–4EXTERIOR/INTERIOR TRIM
Consoles
Consoles and Associated Parts
This illustration is based on RHD
745RW009
Legend
(1) Shift Knob (M/T) / Transfer Knob (A/T)
(2) Assist Grip
(3) Fuel Filler Lid Opener(4) Center Console Assembly
(5) Front Seat Assembly (RH)
(6) Front Console Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the shift knob (M/T) / transfer knob (A/T).
3. Remove the front console assembly.
Remove four fixing screws and disconnect the
switch connectors.
4. Remove the front seat assembly(RH).
Refer to the Front Seat Assembly removal steps in
Seats section.
5. Remove the assist grip.
Remove three bolts.
6. Remove the fuel filler lid opener.
Remove the fuel filter lid opener(1) and disconnect
the cable(2).
686RW007

8J–14EXTERIOR/INTERIOR TRIM
Luggage Side and Quarter Upper Trim Cover (Long Wheel Base)
Luggage Side, Quarter Upper Trim Cover and Associated Parts
760RW017
Legend
(1) Assist Grip
(2) Rear Seat Belt Anchor Bolt Cover and Anchor
Bolt
(3) Quarter Upper Trim Cover
(4) Anchor Bolt
(5) Luggage Side Trim Cover
(6) Luggage Side Lower Cover
(7) Third Seat Assembly and seat Bracket(8) Third Seat Belt Anchor Bolt Cover and Anchor
Bolt
(9) Rear End Floor Trim Cover
(10) Luggage Side Cap
(11) Speaker Grille
(12) Rear Speaker
(13) Luggage Room Light
(14) Rear Roof Trim Cover
Removal
1. Disconnect the battery ground cable.
2. Remove the third seat assembly and seat bracket.
3. Remove the rear end floor trim cover.
4. Remove the luggage side cap.

EXTERIOR/INTERIOR TRIM8J–15
5. Remove the luggage side lower cover.
6. Remove the luggage side trim cover (1).
Remove the rear side fixing screws and pry the trim
cover retainers free from the body panel and the
upper trim cover.
687RS002
7. Remove the luggage room light.
Remove the luggage room light lens and the fixing
screws.
Disconnect the luggage room light connector.
8. Remove the rear roof trim cover.
Pry the trim cover retainers free from the body
panel.
666RS001
9. Remove the speaker grille.
687RS003
10. Remove the rear speaker.
Remove the rear speaker fixing screws and
disconnect the connector.
11. Remove the rear seat belt anchor bolt cover (2) and
the anchor bolt (3).
760RW005
12. Remove the third seat belt anchor bolt cover and
anchor bolt.
Refer to the Third Seat Belt removal procedure in
Seat Belt System section.
13. Remove the assist grip.

8J–16EXTERIOR/INTERIOR TRIM
14. Remove the quarter upper trim cover.
Remove the rear side clips of the trim cover and pry
the quarter upper trim cover retainers free from the
body panel.
687RS004
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Tighten the seat belt anchor bolt to the specified
torque.
Torque: 39 Nꞏm (4.0kgꞏm/29 lb ft)