1998 NISSAN GT-R ignition

TROUBLE DIAGNOSES
Self-diagnosis (Cont'd)
\ I1 // \ 11 // =-I= or =mj= // 11 \ // 11 \
1, = 2.5 sec. t, = 2.0 sec. t, = 1.0 sec.
RB20DE 10 judgement flashes.
Stan signal Malfunctioning unit and circuit I
Except RBPODE 13 judgement flashes.
signal Malfunctioning unit and circuit I
POWER INDICATOR LAMP OR DUAL MATIC A/T
WARNING LAMP INDICATION
If malfunction occurs in electrical system, indicator lamp stays on
longer at corresponding circuit.
Flashing
order
t5 1 Overrun clutch solenoid
1
2
3
4
5
7 1 Lock-up solenoid
Malfunctioning
unit and circuit
Vehicle speed sensor
1
Vehicle speed sensor 2
Throttle position sensor
Shift solenoid
A
Shift solenoid B
I
W fluid temperature sensor, TCM power supply, or throttle posi-
tion sensor power supply
RB20DE
9 1 Engine speed
signal Except
RB20DE
10 1 Line
pressure solenoid I Turbine sensor
I - I Line pressure solenoid
12 1 - I Total control signal
When indicator lamp repeats flashing in 4 Hz, the following malfunctions
may exist: (Insufficient memory backup
powerflCM repiacement1Battery
has been disconnected for prolonged
periodllow battery power)
13
No flashes
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
To facilitate cause investigation of malfunction that is less likely to
reappear, the TCM always stores self-diagnostic results during cus-
tomer operation. This memory cannot be erased even if ignition
switch
is turned ON and OFF repeatedly. To erase the seif-diag-
nostic
results, turn ignition switch
OFF after self-diagnosis has
been performed, or use
"ERASE" function of CONSULT.
- - - - Shift control unit
PNP switch, idle
switch/full switch
Overdrive control switch Stop lamp switch

TROUBLE DIAGNOSES
Symptom Chart
Sharp shock in Engine brake
applied
Shifting
Malfunctions
Slip
(Racing)
hifting
.- erator pedal
Shifting
Shifting
inspection item
Fluid level and status
Control linkage
PNP switch (short/open circuit)
Throttle ~osition sensor (installed)
I Vehicle weed sensor
I Enaine meed sensor
A/T fluid temperature sensor
Engine idle speed
Line
Dressure
Control valve assembly
Shift solenoid
A
Shift solenoid B
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
Accumulator N-D
Accumulator
1-2
Accumulator 2-3
Accumulator 3-4 (N-R) Ignition coil and starter motor
Overdrive control switch
I AfT mode switch (AUTO)
Torque converter
1 Oil pump
I Reverse clutch
I High clutch
I Forward clutch
I Forward one-wav clutch
I Overrun ciutch
1 Low one-wav clutch
I Low reverse brake
Brake. band (including servo)
Parking linkage

Symptom Chart (Cont'd)
Greater noise
Malfunctions
Inspection item No shifting
I Shifting I
Fluid level
and status 11
Control linkage
-
(I) C 0 .- c. .- (I) 0 a
v
-CU
n - 1
PNP switch
(shortlopen
circuit)
Throttle position sensor (installed)
2 2
Vehicle speed sensor
I Engine speed sensor -
-T
L o 1 Control valve assembly .- - -- Shift solenoid A 4 3
. ' Shift solenoid 6 4 cut I1
--, Line pressure solenoid .- 5 -t Lock-up solenoid ?
6 Overrun clutch solenoid 3
Accumulator N-D
1 Accumulator 1-2 I 1-
Accumulator 2-3
Accumulator 3-4 (N-R)
Ignition coil and starter motor
I Overdrive control switch I 1-
A/T mode switch (AUTO)
A/T mode switch (POWER) I - I Ail mode switch (SNOW) I
I Torque converter I I
1 Oil pump I I -- - - Reverse clutch 0 -
'g High clutch a 4 6
%I Forward clutch I I - .- a Forward one-way clutch -
$ Overrun clutch a, 8
Low one-way clutch
O Low reverse brake 7
Brake band (including servo) 7
Parking linkage

TROUBLE DIAGNOSES
Symptom Chart (Cont'd)
xi - - ([I C V) a, C .- cn C W
t 0 .- .L 2 a, - 8 0 ([I L 0 0 Q
& 0 a, a, Q V)
5 E .- X
i! L a
zl -I - 1 -
- 2 -
-
-
-
-
-
5 - 3 - 4 -
-
-
-
-
-
-
-
-
-
-
-
-
I1 - 0 - 6 - 7 -
-
-
-
-
9 - 8 -
-
vj c 0 .- - .- V) 0 n
Q 7J C ([I
t C .- r ([I c. V) c. 0 C V) a 0 7J 0, C .- 0 C W -
- 2 - 3 -
-
- -
-
1 -
-
-
-
- - a +- ([I a a, 2 0 c. 0 C V) a, 0 u a, - 0 2
8 - 1 -
-
-
-
-
-
-
-
2 - 3 -
-
-
-
-
-
-
-
-
-
-
- I
i
g
- 4 -
-
-
-
-
-
-
B- ; 2 to a =? - 0,
2 5.j c 2.z 2 a0 - 0- z & 5 0 gE V) V)o C 02 .s nu 5 ng %-([I C O c --t .- V) a V) r aa ([I z gz a, a- c 50 -6 s
6 $2
11
2
I
I
Malfunctions
Inspection item
I I I Fluid level and status I I Control linkage 2
PNP switch (shortfopen circuit) 1 I I I Throttle position sensor (installed) 111213
Vehicle speed sensor
214
Engine speed sensor L -
AIT fluid temperature sensor
Engine idle weed
Line pressure
Control valve assembly
Shift solenoid A 3
3
Shift solenoid B 4 4
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
u I I I -
Accumulator N-D I I 1 I Accumulator 1-2
Accumulator 2-3 I Accumulator 3-4 (N-R)
Ignition coil and starter motor
Overdrive control switch
Torque converter
tg Reverse clutch .- High clutch
2 Forward clutch C .- a Forward one-way clutch -.
$ Overrun clutch 0, 8
? Low one-way clutch 3= O Low reverse brake 9
Brake band (including servo)
Parking linkage

ANTI-LOCK BRAKE SYSTEM
ABS control unit connector
Terminal No.
Control Unit InputlOutput Signal Specifications
USING CIRCUIT TESTER
To perform the following inspection, the ignition switch should be
turned
ON with ABS control unit connector and actuator connector
properly connected.
Item Specifications*l
Battery Ignition switch ON: Battery voltage (Approx. 12V)
Brake pedal is depressed: Battery voltage (Approx. 12V)
Stop lamp signal
Brake pedal is not depressed: Less than approx.
2V
ABS motor is running
ABS motor relay (in
CONSULT active test mode): Less than approx.
2V
ABS motor is stopped: Battery voltage (Approx.
12V)
Actuator relay is activated (with engine running): Less than approx. 2V
Actuator relay Actuator
relay is not activated (with fail-safe function activated and engine
not running): Battery voltage (Approx. 12V)
Actuator relay is activated (with engine running): Battery voltage (Approx.
Actuator relay 1 2V)
monitor Actuator
relay is not activated (with fail-safe function activated and engine
not running): Approx. OV
Front
right inlet
Actuator is activated (in CONSULT active test mode), or actuator relay is
solenoid not activated (with fail-safe function activated and engine not running):
Rear inlet solenoid Approx. OV
Front
left inlet Actuator
is not activated and actuator relay is activated (with vehicle
solenoid stopped
and engine running): Battery voltage (Approx. 12V)
ABS motor is running (in CONSULT active test mode): Battery voltage
ABS motor monitor (Approx. 12V)
ABS motor is stopped (with ignition switch
ON): Approx. OV
ABS warning lamp
ON'2:
Approx. OV
ABS warning lamp
ABS warning lamp
OFF'2:
Battery voltage (Approx. 12V)
Front right wheel
sensor Wheels are turning (Approx. 30
krn/h)*3: Pulse generates.
Front: Approx. 200
Hz
sensor
Rear: Approx. 400 Hz
Front right outlet
Actuator is activated (in CONSULT active test mode), or actuator relay is
not activated (with fail-safe function activated and engine not running):
Rear outlet
sole-
Approx. OV
I lUlU / Actuator is not activated and actuator relay is activated (with vehicle Front left Outlet stopped and engine running): Battery voltage (Approx. 12V)
solenoid
'1:e
to
tooen
a connector terminal when
using a circuit tester for inspection. Control
I
unit
power
supply circuit
ST
Stop lamp switch
and circuit
ABS motor, motor
R8
relay and circuit
ABS actuator relay
and circuit
pL
ABS warning lamp
and circuit, ABS
actuator relay
SD monitor circuit
ABS solenoid and
circuit
ABS motor monitor
circuit
ABS warning lamp
and circuit
Wheel sensors and circuit
ABS solenoid and
circuit
'2: ABS warning lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected ABS warning lamp OFF: One second after the ignition switch is turned ON (with the system in normal condition) *3: Tire pressure must be in accordance with specification.

ANTI-LOCK BRAKE SYSTEM
Control Unit InputfOutput Signal Specifications
(Cont'd)
USING CONSULT
Indicated are the control unit computed data. If the output circuit (harness) should be open or short-
circuited, correct values may be displayed.
Check item (Reference)
Data monitor
Display Condition
Monitor
item
Specifications
Vehicle is stationary.
I 0 kdh
FR RH SENSOR
FR LH SENSOR
RR SENSOR
[kdh]
Virtually the same speed
as speedometer (within
+I 0%)
Wheel sensor and circuit
Wheel speed
Vehicle is
drivem'l
Brake pedal is
depressed. Stop lamp switch and
circuit
STOP
LAMP SW
[ON-OFF] Brake pedal status
Brake pedal is not
depressed. OFF
-- --
Actuator (solenoid)
is
activated (at CONSULT
active test),
or
actuator relay is not
activated (with fail-safe
function activated and
engine not running).
FR
RH IN SOL
FR
LH IN SOL
REAR IN SOL
[ON-OFF]
ABS solenoid and circuit
Solenoid status
FR RH OUT SOL
FR
LH OUT SOL
REAR OUT SOL
[ON-OFF]
-- -- - -- -
Actuator (solenoid) is not
activated and actuator
relay is activated (with
vehicle stopped and
engine running).
Actuator relay is acti-
vated (with engine run-
ning).
Actuator relay is not acti-
vated (with fail-safe
function activated and
engine not running).
ABS actuator relay and
circuit
OFF
ON
OFF
ACTUATOR
RLY
[ON-OFF] Actuator
relay status
Motor relay and motor
are activated (at CON-
SULT active test). ABS
motor, motor relay,
and circuit
MOTOR
RLY
[ON-OFF] Motor
relay and motor
status Motor relay and motor
are not activated. OFF
ABS warning lamp and
circuit
- -
Waming lamp ON'2 1 ON
WARNING LAMP
[ON-OFF] ABS
warning lamp sta-
tus
Power supply voltage
provided for control unit -- -
Warning lamp OFF'2 1 OFF
Control unit power sup-
ply circuit - -
BAlTERY VOLT [V] Ignition switch
ON
'1: Tire pressure must be in accordance with specification. "2: ABS warning lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected ABS warning lamp OFF: One second after the ignition switch is turned ON (with the system in normal condition)

ANTI-LOCK BRAKE SYSTEM
Precautions for Trouble Diagnosis
After performing trouble diagnosis, be sure to erase trouble stored in memory. Refer to "CONSULT' (next
page) or "SELF-DIAGNOSIS"
(BR-15).
As for the concerns that are difficult to duplicate, move harnesses or harness connectors by hand to check
if there is any poor mating of connector halves or faulty connection.
Do not force to open a connector terminal when using a circuit tester for inspection.
Read GI section thoroughly in advance and make sure of all the general precautions.
Basic Inspection
BASIC INSPECTION 1 - Brake fluid level and leakage AT
1. Check brake fluid level in reservoir tank. Replenish brake fluid if necessary.
2. Check for leakage at or around brake piping and ABS actuator. If leakage or seepage is noted, proceed
as follows:
If ABS actuator connectors are loose, tighten to specified torque. Recheck to ensure that leakage is no
longer present.
If flare nut threads at piping connectors or actuator threads are damaged, replace faulty parts with new 87
ones. Recheck to ensure that leakage is no longer present.
If brake fluid leaks through areas other than actuator connectors, wipe off using a clean cloth. Recheck
for leakage or seepage. If necessary, replace faulty parts with new ones.
R8
If brake fluid leaks at or seeps through ABS actuator, wipe off using a clean cloth. Recheck for leakage
or seepage. If necessary, replace
ABS actuator with new one.
CAUTION: HA
ABS actuator cannot be disassembled. Do not attempt to disassemble it.
BASIC INSPECTION 2 - Loose power line terminal
Check battery terminals (positive and negative) and battery mounting (ground) for looseness.
BASIC INSPECTION 3 - ABS warning lamp
1. Turn ignition switch "ON" to ensure that ABS warning lamp lights up for approximately 1 second. If ABS
warning lamp does not light, check ABS warning lamp circuit.
2. After driving vehicle at approx. 30 km/h for approx. 1 minute, check to ensure that ABS warning lamp
remains off. If ABS warning lamp lights, perform self-diagnosis procedures.
3. After performing self-diagnosis procedures, be sure to erase trouble stored in memory.

ANTI-LOCK BRAKE SYSTEM
CONSULT
CONTROL UNIT PART NUMBER
The part number that is shown on the control unit label and CON-
SULT 47850 AAOOO
- SELF-DIAGNOSIS PROCEDURE
Coliect information on the concern from the customer, and then
perform basic inspections.
Turn ignition switch
OFF and connect CONSULT connector to
data link connector for CONSULT on the vehicle.
Start engine and drive vehicle at approx.
30 km/b for approx.
1 minute.
Stop vehicle and touch "START",
"ABS" and "SELF-DIAG
RESULTS" sequentially on the CONSULT screen with engine
running.
If "START" is touched immediately after engine is started
or ignition switch is turned on,
"ABS" may not be dis-
played on "SELECT
SYSTEM" screen. To display "ABS",
repeat the self-diagnosis procedure from the beginning.
Self-diagnosis results are displayed on the screen. (Touch
"PRINT" to print out the self-diagnosis results, if necessary.)
If
"NO FAIL" is displayed, inspect ABS warning lamp. Refer to
the previous page.
Perform appropriate inspection from the self-diagnostic results
mode and repair or replace faulty parts.
Start engine and drive vehicle at approx. 30
km/b for approx.
1 minute.
Recheck to ensure that there is no other malfunction.
Turn ignition switch OFF to prepare for erasing the trouble
stored in memory.
Start engine and touch "START",
"ABS", "SELF-DIAG
RESULTS" and "ERASE" sequentially on the CONSULT
screen to erase the trouble stored in memory.
If the trouble stored in memory is not erased, repeat step
6.
10. Drive vehicle at approx. 30 km/h for approx. 1 minute and then
confirm that ABS warning lamp is
off.