Page 171 of 230
REMOTE CONTROL ENTRY SYSTEM
lnspection before Trouble Diagnoses
Check system.
Check that other systems that use the following signals work
properly.
Check that component connectors are connected properly.
Trouble Diagnoses
SYMPTOM CHART
Symptom
None of the doors lock with the remote
control switch.
None of the doors unlock with the
remote control switch.
Door locks other than the driver door do
not operate with the remote control
switches.
Only the driver door lock does not oper-
ate with the remote control switch. Door
switch circuit Malfunctioning item
Faulty door switch to
remote control entry control unit
harness Possible cause
Key-in detection switch circuit
Faulty key-in detection switch to remote control entry control
unit harness
Remote control entry control unit
Key-in detection switch circuit
Faulty remote control entry control unit
Faulty key-in detection switch to remote control entry control
unit harness
Remote control entry control unit
Central door lock system circuit
Remote control entry control unit
Driver door lock actuator circuit
Remote control entry control unit
Faulty remote control entry control unit
Refer to
"CENTRAL DOOR LOCK SYSTEM", EL-2. Faulty combination meter (meter control unit) to remote
control entry control unit harness
Faulty remote control entry control unit
Faulty driver door lock actuator Faulty driver door lock actuator to remote control entry
control unit harness
Faulty remote control entry control unit
mA before
Use lithium
checking ihe battery.
photo battery (CRI 620
Component Parts lnspection
BATERY CHECK
Specification: Approx. 2.5 - 3.OV
CAUTION:
Connect resistance
(300Q) so that the current is approx. 10
or equivalent) for
replacement.
Page 172 of 230
REMOTE CONTROL ENTRY SYSTEM
ID Code Entry Procedure
Enter the identity (ID) code manually when:
remote controller or control unit is replaced.
an additional remote controller is activated.
To enter the ID code, follow the procedures below.
PROCEDURE
I Close all doors and lock driveis side door. I
Insert and remove the key from the ignition more than six times within 10 seconds.
(Power door lock will then unlock.)
Within
3 seconds after door lock is unlocked, turn ignition key switch to "ACCn posi-
tion and lock the driver's side door.
At this time, the original ID codes are erased.
Push any button on the new remote controller once. (Power door lock will then
unlock.)
At this time, the new ID code is entered. e
Lock driver's side door.
Do you
want to enter any additional remote controller ID codes?
A maximum four ID codes may be entered. Any attempt to enter more will be
ignored.
I Open driver's side door or turn the ignition key switch to 'OFF position. I
No
END.
After entering the identity (ID) code, check the operation of remote control
entry system.
Yes
NOTE
If you need to activate more than two additional new remote controllers, repeat the procedure
"Additional ID code entry" for each new remote controller.
If the same ID code that exists in the memory is input, the entry will be ignored.
Entry of maximum four ID codes is allowed and any attempt to enter more will be ignored.
Page 182 of 230
IGNITION KEY-OPERATED ILLUMINATION SYSTEM
Behind combination meter Component Parts Location
Meter control unit
Circuit Diagram
7, . .
& Driver door lock detection switch
T
2 1 r Passenger door SW Rear RH door SW 326
' a
Rear LH door SW
3 - -
Room lamp
IGN SW illumination
TK24 (Brown) TK20 (Brown) TK20 (White) EL-2 178D I 1 J
Meter Control Unit Input/Output Signal
Terminal No.
Specifications I I
Specification
Approx.
OV
Approx. 12V
Approx. OV
Approx. 5V
Approx. 12V
Approx. OV
Approx. 12V
Approx. 12V
Approx. OV
Approx. 12V
Approx. OV
Approx. OV
Approx. 12V
Approx. OV'
Approx. 12V
Measuring condition
Signal name Ignition
Operation or condition
switch
Driver door switch ON (Open)
OFF Driver door switch
signal OFF (Closed)
Driver door lock
sig-
Door is unlocked. (Switch ON)
nal OFF
Door is locked. (Switch OFF)
Battery OFF
-
Open a door. (ON)
Door switch signal
OFF
Close all the doors. (OFF)
Ignition power supply ON
-
Key-in detection Remove
the ignition key.
switch signal OFF
Insert the ignition key.
Ground ON
-
OFF Room lamp switch:
Insert the ignition key. Each door switch
Room lamp, ignition Neutral position ON
(Open)
OFF (Closed)
switch illumination
Remove the ignition key from the
signal
- lamp switch: Close all the doors. key cylinder.
Neutral position
Turn the ignition switch ON.
Page 196 of 230
IGNITION KEY WARNING BUZZER AND LIGHT WARNING BUZZER
I Behind combination meter
Meter control unit Component Parts Location
J
Circuit Diagram
Meter Control Unit
InputlOutput Signal
Specifications
Terminal No.
Driver door switch signal
Signal
name
OFF Measuring condition
Ignition switch
I Measuring method Specification
Driver door switch
29
ON (Open)
OFF (Closed)
42
Approx. OV
Approx. 12V
Ignition power supply
54
55
Key-in detection switch
signal 1 OFF
ON
Lighting switch signal
Ground Approx. 12V
Remove
the ignition key.
Insert the ignition key. Approx. OV
Approx. 12V
Approx. 12V
Approx. OV
Approx. OV
I
OFF
ON Lighting
switch: 1 ST ON
OFF
-
