1998 MITSUBISHI MONTERO wheel

oil additives coolant level fuel pressure coolant capacity tow tailgate

Page 241 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Fig. 18: Exploded View Of Master Cylinder (Typical) Courtesy of Mitsubishi Motor Sales of America. TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS (DIAMANTE)��\ ��$

Page 242 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Wheel Cylinder Bolt ........................................ 89 (10)\ ��\ ��\ ��\ ��\ ��\ ��\ ��$

Wheel Cylinder Bolt ........................................ 89 (10)\
\
\
\
\
\
\
\

TORQUE SPECIFICATIONS (GALANT)\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Brake Line Flare Nuts ...................................... 11 (15)\
Caliper Guide & Lock Pin Bolt .............................. 54 (73)\
Caliper Mounting Bolts ..................................... 66 (90)\
Rear Hub-To-Knuckle Nut .................................... 60 (81)\
Wheel Lug Nut ....................................... 67-81 (90-110)\
INCH Lbs. (N.m)
Master Cylinder Mounting Booster Nut ...................... 115 (13)\
Bleeder Screw ............................................... 71 (8)\
Wheel Cylinder Bolt ........................................ 89 (10)\
\
\
\
\
\
\
\

TORQUE SPECIFICATIONS (MIRAGE)\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Brake Line Flare Nuts ...................................... 11 (15)\
Caliper Guide Pin Bolt ..................................... 36 (49)\
Caliper Lock Pin Bolt ................................ 61-69 (83-93)\
Caliper Mounting Bolts .............................. 66-81 (90-110)\
Rear Wheel Bearing Nut ................................... 127 (172)\
Wheel Lug Nut ....................................... 67-81 (90-110)\
INCH Lbs. (N.m)
Master Cylinder Mounting Booster Nut ...................... 115 (13)\
Bleeder Screw ............................................... 71 (8)\
Wheel Cylinder Bolt ........................................ 89 (10)\
\
\
\
\
\
\
\

TORQUE SPECIFICATIONS (MONTERO)\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Brake Line Flare Nuts ...................................... 11 (15)\
Caliper Guide & Lock Pin Bolt
Front .................................................... 54 (73)\
Rear ..................................................... 32 (44)\
Caliper Mounting Bolt ...................................... 65 (88)\
Wheel Lug Nut ....................................... 72-87 (98-118)\
Rear Axle Bearing Retainer Nut ................... 145-173 (196-235)\
INCH Lbs. (N.m)
Master Cylinder Mounting Nut .............................. 115 (13)\
Bleeder Screw ............................................... 71 (8)\
\
\
\
\
\
\
\

TORQUE SPECIFICATIONS (MONTERO SPORT)\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Brake Line Flare Nuts ...................................... 11 (15)\
Caliper Guide & Lock Pin Bolt (Front) ...................... 54 (73\
)
Caliper Mounting Bolt

Page 243 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Front .................................................... 66 (90)\ Rear .................................................... 94 (127)\ Wheel Lug Nut 15x6" Wheel .........................$

Front .................................................... 66 (90)\
Rear .................................................... 94 (127)\
Wheel Lug Nut
15x6" Wheel ..................................... 87-101 (118-137)\
15x7" Wheel ....................................... 72-86 (98-117)\
Rear Axle Bearing Retainer Nut ................... 145-173 (196-235)\
INCH Lbs. (N.m)
Master Cylinder Mounting Nut .............................. 115 (13)\
Bleeder Screw ............................................... 71 (8)\
Wheel Cylinder Nut ......................................... 89 (10)\
\
\
\
\
\
\
\

TORQUE SPECIFICATIONS (3000GT)\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Brake Line Flare Nuts ...................................... 11 (15)\
Caliper Guide & Lock Pin Bolt (FWD)
Front .................................................... 54 (73)\
Rear ..................................................... 20 (27)\
Caliper Mounting Bolts
Front .................................................... 66 (90)\
Rear ............................................... 36-43 (49-59)\
Front Axle Shaft Nut ..................................... 166 (230)\
Rear Wheel Bearing Nut
AWD ............................................ 192-221 (260-300)\
FWD .................................................... 170 (230)\
INCH Lbs. (N.m)
Master Cylinder Mounting Nut ............................... 84 (10)\
\
\
\
\
\
\
\

BRAKE SYSTEM BRAKE SPECIFICATIONS
BRAKE SPECIFICATIONS (DIAMANTE)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance ...................... .016-.024 (.40-.60)\
Disc Runout ............................................. .003 (.08)\
Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear ................................................... .33 (8.4)\
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ......................... 1.0 (25.4)\
Pad Lining Thickness (Minimum)
Front ................................................. 1.08 (2.0)\
Rear .................................................. 1.04 (1.0)\
\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (ECLIPSE)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance ...................... .023-.033 (.65-.85)\
Disc Runout ............................................. .003 (.08)\
Disc Diameter
AWD .................................................... 9.0 (228)\
Except AWD ............................................. 8.0 (204)\

Page 244 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Disc Thickness (Minimum) Front ................................................. .88 (22.4)\ Rear ................................................... .33 (8.4)\ Drum Inside Diameter (Maximum$

Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear ................................................... .33 (8.4)\
Drum Inside Diameter (Maximum) ........................... 9.1 (231\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter
With ABS .............................................. 1.0 (25.4)\
Without ABS ........................................... .93 (23.8)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (GALANT)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance
Single Booster ............................... .024-.031 (.60-.80)\
Tandem Booster ............................... .016-.024 (.40-.60)\
Disc Runout ............................................. .003 (.08)\
Disc Thickness (Minimum) ................................ .88 (22.4\
)
Drum Inside Diameter (Maximum) ........................... 9.1 (231\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ......................... 1.0 (25.4)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (MIRAGE)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.033 (.65-.85)\
Disc Runout ........................................... .006 (.0024)\
Disc Thickness (Minimum) ................................ .65 (16.4\
)
Drum Inside Diameter (Maximum) ........................... 8.1 (206\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ........................ .87 (22.22)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (MONTERO)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.035 (.65-.90)\
Disc Runout
Front ................................................. .004 (.10)\
Rear .................................................. .003 (.08)\
Disc Thickness (Minimum)
Front ................................................. 1.0 (25.4)\
Rear .................................................. .65 (16.4)\
Hub End Play ........................................... .0098 (.25)\
Master Cylinder Inside Diameter ........................ .937 (23.8)\
Pad Lining Thickness (Minimum)
Front ................................................. 1.08 (2.0)\
Rear ........................................................ (1)
Parking Brake Drum Diameter (Maximum) .................. 7.795 (198\
)

Page 245 of 1501

$MITSUBISHI MONTERO 1998 Service Manual (1) - Information not available from manufacturer.��\ ��\ ��\ ��\ ��\ ��\ ��\ ��$

(1) - Information not available from manufacturer.\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (MONTERO SPORT)\
\
\
\
\
\
\

Application In. (mm)\
Disc Runout
Front ................................................. .002 (.06)\
Rear .................................................. .003 (.08)\
Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear .................................................. .65 (16.4)\
Drum Diameter (Maximum) .............................. 10.71 (272.0\
)
Hub End Play (Maximum) .................................. .002 (.05\
)
Master Cylinder Inside Diameter ........................ .937 (23.8)\
Pad Lining Thickness (Minimum) .......................... 1.08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter .......................... .90 (22.8)\
\
\
\
\
\
\
\

BRAKE SPECIFICATIONS (3000GT)\
\
\
\
\
\
\

Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.030 (.65-.75)\
Disc Runout
Front
AWD ................................................. .004 (.10)\
FWD ................................................. .003 (.07)\
Rear ................................................ .003 (.08)\
Disc Thickness (Minimum)
Front
AWD ................................................ 1.12 (28.4)\
FWD ................................................. .88 (22.4)\
Rear
AWD ............................................... .72 (18.4)\
FWD ............................................... .65 (16.4)\
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ......................... 1.0 (25.4)\
Pad Lining Thickness (Minimum) .......................... 1.08 (2.0\
)
Parking Brake Drum Diameter (Maximum) ................... 6.65 (169\
)
\
\
\
\
\
\
\

Page 247 of 1501

MITSUBISHI MONTERO 1998 Service Manual Montero .............................. 10.0 Qts. (9.5L)
Montero Sport
2.4L
With Rear Heater .................. 9.5 Qts. (9.0L)
Without Rear Heater ............... 8.5 Qt

Montero .............................. 10.0 Qts. (9.5L)
Montero Sport
2.4L
With Rear Heater .................. 9.5 Qts. (9.0L)
Without Rear Heater ............... 8.5 Qts. (8.0L)
3.0L
With Rear Heater ................ 10.6 Qts. (10.0L)
Without Rear Heater ............... 9.5 Qts. (9.0L)
3000GT ................................ 8.5 Qts. (8.0L)
Crankcase (Includes Filter)
Diamante ............................... 4.5 Qts. (4.3L)
Eclipse
Non-Turbo ............................ 4.5 Qts. (4.3L)
2.0L Turbo ........................... 4.6 Qts. (4.4L)
Galant ................................. 4.5 Qts. (4.3L)
Mirage
1.5L ................................. 3.5 Qts. (3.3L)
1.8L ................................. 4.0 Qts. (3.8L)
Montero ............................ (1) 5.0 Qts. (4.8L)
Montero Sport
2.4L ................................. 4.5 Qts. (4.3L)
3.0L ................................. 5.2 Qts. (4.9L)
3000GT
Non-Turbo ............................ 4.5 Qts. (4.3L)
Turbo ................................ 5.0 Qts. (4.6L)
Differential (SAE 80W-90/API GL-5)
Eclipse ................................... .9 Qt. (.8L)
Montero
Front ................................ 1.3 Qts. (1.2L)
Rear ................................. 3.3 Qts. (3.2L)
Montero Sport
Front ................................ 1.2 Qts. (1.1L)
Rear
2.4L ............................... 1.6 Qts. (1.5L)
3.0L ............................... 2.7 Qts. (2.6L)
3000GT ................................. 1.2 Qts. (1.1L)
Manual Transaxle (SAE 75W-85/API GL-4)
Eclipse
Non-Turbo ( 2) ........................ 2.1 Qts. (2.0L)
Turbo
AWD ................................ 2.4 Qts. (2.3L)
FWD ................................ 2.1 Qts. (2.0L)
Galant ................................. 2.3 Qts. (2.2L)
Mirage
1.5L ................................. 2.2 Qts. (2.1L)
1.8L ................................. 2.3 Qts. (2.2L)
3000GT
AWD .................................. 2.5 Qts. (2.4L)
FWD .................................. 2.4 Qts. (2.3L)
Manual Transmission (SAE 75W-85/API GL-4)
Montero ................................ 3.3 Qts. (3.2L)
Montero Sport .......................... 2.4 Qts. (2.3L)
Power Steering (Dexron-II)
3000GT W/4-Wheel Steering .............. 3.2 Pts. (1.5L)
Montero ................................ 2.2 Pts. (1.1L)
All Others .............................. 1.9 Pts. (.9L)
Transfer Case (SAE 75W-85/API GL-4)
Eclipse (AWD) ........................... 1.1 Pts. (.5L)
Montero ................................ 5.0 Pts. (2.5L)
Montero Sport .......................... 4.6 Pts. (2.3L)
3000GT .................................... .7 Pt. (.3L)
( 1) - Add .5 qt. (.3L) if oil cooler is drained.

Page 260 of 1501

MITSUBISHI MONTERO 1998 Service Manual specified, bleed system and inspect hydraulic and clutch components.
See CLUTCH PEDAL SPECIFICATIONS table.
CLUTCH PEDAL INTERLOCK SWITCH
1) Place transmission in Neutral and apply

specified, bleed system and inspect hydraulic and clutch components.
See CLUTCH PEDAL SPECIFICATIONS table.
CLUTCH PEDAL INTERLOCK SWITCH
1) Place transmission in Neutral and apply parking brake.
Turn ignition switch to START position with clutch pedal not
depressed. Engine should not crank. If engine cranks, adjust or
replace interlock switch.
2) Disconnect interlock switch connector. Interlock switch
connector is located at clutch pedal. Depress and release interlock
switch. Using ohmmeter, check continuity between interlock switch
terminals. If continuity exists with interlock switch depressed and
does not exist with switch released, switch is okay. Adjust or replace
as necessary.
REMOVAL & INSTALLATION
CLUTCH ASSEMBLY
Removal (2WD Models)
1) Disconnect negative battery cable. Remove shift knob, dust
cover retaining plate, gaskets, stopper plate and control lever
assembly. Raise and support vehicle.
2) Remove front exhaust pipe. Drain transmission fluid. Index
mark drive shaft flange and remove drive shaft.
3) Disconnect back-up light switch connector, speedometer
cable connection and exhaust pipe mounting bracket. Remove lower
bellhousing cover. Disconnect clutch cable from clutch lever.
4) Support transmission with jack. Remove rear engine mount
nuts and bolts from transmission. Remove crossmember with rear engine
mount. Remove remaining bellhousing bolts, move transmission toward
rear and lower from vehicle.
5) If reusing pressure plate, index mark pressure plate to
flywheel for installation reference. Install a clutch alignment tool
to prevent pressure plate and clutch disc from dropping. Loosen
pressure plate bolts gradually in a crisscross pattern to avoid
warping pressure plate flange during removal. Remove pressure plate
and clutch disc. See Fig. 3.
Inspection
1) Check release bearing and release fork for damage or wear.
DO NOT clean release bearing assembly in solvent.
2) Inspect pressure plate surface for wear, cracks, and/or
discoloration. Measure diaphragm spring ends for wear and uneven
height. Replace assembly if height difference between fingers exceeds
.02" (.5 mm).
3) Check facing of clutch disc for loose rivets, uneven
contact, deterioration, seizure or oil saturation. Measure distance
from clutch disc surface to head of rivet. Replace clutch disc if
distance is less than .012" (.30 mm). Replace worn or defective
components as necessary. See Fig. 4.
CAUTION: Install clutch disc with manufacturer's stamp mark (located
near hub of clutch disc) toward pressure plate.
Installation
1) Using a clutch alignment tool, install pressure plate and
clutch disc. If reusing pressure plate, ensure index marks are
aligned. Tighten bolts evenly in a crisscross pattern to
specification. See TORQUE SPECIFICATIONS . See Fig. 3.
2) Clean release bearing sliding surface. DO NOT clean

Page 261 of 1501

MITSUBISHI MONTERO 1998 Service Manual release bearing with solvent. Apply a light coat of multipurpose
grease to release bearing sliding surface. Apply a very light coating
of grease to input shaft splines. DO NOT allow grease or dirt on

release bearing with solvent. Apply a light coat of multipurpose
grease to release bearing sliding surface. Apply a very light coating
of grease to input shaft splines. DO NOT allow grease or dirt on
clutch disc or pressure plate surfaces.
3) To install remaining components, reverse removal
procedure. Refill all fluids to proper levels. Adjust all control
cables, clutch pedal height and free play. See CLUTCH PEDAL HEIGHT and
CLUTCH PEDAL FREE PLAY under ADJUSTMENTS. See Fig. 1.
Removal (4WD Models)
1) Remove switch panel from rear console. Remove suspension
control switch or hole cover. Disconnect rear console harness
connector. Remove side panel. Remove rear console assembly. Remove
shift lever knob(s). Remove floor console harness connector. Remove
front console assembly.
2) Move transmission lever to Neutral position and transfer
lever to 4H (4WD high range) position. Remove control lever boot
retainer and boot. Remove transmission and transfer control lever
assemblies. Remove control lever bushing (transmission), gaskets and
stopper plates.
3) Raise and support vehicle. Remove skid plate and front
exhaust pipe. Drain transmission and transfer case fluid. Index mark
front and rear drive shaft flanges. Remove front and rear drive
shafts.
4) Remove drive shaft dust seals. Disconnect HI/LO and
2WD/4WD detection switch connectors. Disconnect back-up light switch
connector. Disconnect center differential lock detection switch
connector. Disconnect center differential lock operation switch
connector. Disconnect 4WD operation detection switch.
5) Disconnect speedometer cable. Remove clutch slave cylinder
heat shield. Remove clutch slave cylinder (without disconnecting
hydraulic line) and wire aside. Remove starter and starter cover.
Remove heat shield, both transmission stays and bellhousing lower
cover.
6) Support transmission with transmission jack. Remove
transfer case roll stopper and bracket. Remove crossmember and engine
mounting rear insulator. Remove transfer case protector bracket and
mass damper. Remove remaining bellhousing bolts. Pull toward rear of
vehicle to free transmission input shaft from clutch. Lower
transmission/transfer assembly from vehicle.
7) If reusing pressure plate, mark pressure plate to flywheel
for installation reference. Insert a clutch alignment tool to prevent
pressure plate and clutch disc from dropping. Loosen pressure plate
bolts gradually in a crisscross pattern to avoid warping pressure
plate flange during removal. Remove pressure plate and clutch disc.
See Fig. 3 .
Fig. 3: Removing & Installing Clutch On Flywheel (Typical)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
1) Check release bearing and release fork for damage or wear.

Load next 8 pages

Page: < prev 1-10 ... 17-24 25-32 33-40 41-48 49-56 57-64 65-72 73-80 81-88 ... 208 next >

fuel additives start stop button immobilizer bolt pattern oil viscosity phone