1998 MITSUBISHI MONTERO oil pressure

Fig. 18: Oil Pressure Gauge Resistance Test Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America
Fig. 19: Oil Pressure Gauge Resistance Test Terminals (3000GT)
Courtesy of Mitsubishi Motor Sales of America
NOTE: On Montero Sport, oil pressure gauge is mounted on
multi-meter assembly on center of dashboard.
Circuit Test (Montero Sport)
1) Disconnect harness connector from oil pressure sending

unit. Turn ignition on. Check voltage between ground and sending unit
harness-side connector. If battery voltage is present, problem is
intermittent. If battery voltage is not present, go to next step.
2) Check sending unit harness connector. Repair as necessary.
If connector is okay, check circuit (Yellow wire) between oil pressure\
gauge and oil pressure sending unit. See WIRING DIAGRAMS. Repair as
necessary. If circuit is okay, go to next step.
3) Remove multi-meter assembly. Check voltage between ground
and harness-side connector terminal No. 10 (Red/Black wire). See
WIRING DIAGRAMS . If battery voltage is present, problem is
intermittent. If battery voltage is not present, go to next step.
4) Check harness connector to multi-meter assembly. Repair as
necessary. If connector is okay, check circuit between multi-meter
harness connector and fusible link No. 6. See WIRING DIAGRAMS. Repair
as necessary. If circuit is okay, go to next step.
5) Turn ignition on. Check voltage between ground and multi-
meter harness-side connector terminal No. 11 (Black/White wire). See
WIRING DIAGRAMS . If battery voltage is present, problem is
intermittent. If battery voltage is not present, go to next step.
6) Check harness connector to multi-meter assembly. Repair as
necessary. If connector is okay, check circuit between multi-meter
assembly harness connector and ignition switch. See WIRING DIAGRAMS.
Repair as necessary. If circuit is okay, go to next step.
7) Turn ignition off. Check continuity between ground and
multi-meter assembly harness-side connector terminal No. 3 (Black
wire). If continuity is present, problem is intermittent. If
continuity is not present, go to next step.
8) Check harness connector to multi-meter assembly. Repair as
necessary. If connector is okay, check circuit (Black wire) between
multi-meter assembly harness connector and ground. See WIRING DIAGRAMS
. Repair as necessary. If circuit is okay, problem is intermittent.
Gauge Sending Unit Resistance Test (Montero Sport)
Disconnect harness connector to oil pressure sending unit.
Start and idle engine. Check resistance between oil pressure gauge
sending unit terminal and engine block. Resistance should be about 2
ohms. Replace sending unit if resistance is not as specified.
REED SWITCH
Continuity Check (Montero)
1) Remove instrument cluster. See INSTRUMENT CLUSTER under
REMOVAL & INSTALLATION. Check continuity between reed switch terminals
No. 1 and 2. See Fig. 20.
2) Ensure continuity pulses on and off 4 times per revolution
of speedometer shaft connection. If continuity is not as specified,
replace reed switch.
Fig. 20: Identifying Reed Switch Test Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America
SPEEDOMETER TEST

FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1)







\





 



\









\









\








 \









\









\





 
Item  Condition  Specification 











\








\









\









\








\









\









\





\f

Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1)









\









\









\








\









\









\
\f

 Oil Filter  0.32 Qts. (0.3L) 












\









\









\








\









\









\
\f

 Oil Cooler  0.32 Qts. (0.3L) 











\








\









\









\








\









\









\





\f

Power  Drained  1.1 Qts. (1.0L) 

Steering   











\








\









\









\








\









\









\





\f

Automatic  Drained  8.9 Qts. (8.5L) 

Transmission   











\








\









\









\








\









\









\





\f

Manual  Drained  3.3 Qts. (3.2L) 

Transmission   











\








\









\









\








\









\









\





\f

Transfer Case Drained  2.6 Qts. (2.5L) 











\








\









\









\








\









\









\





\f

Front Axle  Drained  1.3 Qts. (1.2L) 











\








\









\









\








\









\









\





\f

Rear Axle  Drained  3.3 Qts. (3.2L) 











\








\









\









\








\









\









\





\f

A/C  Drained  27 oz (760 g) 

Refrigerant   











\








\









\









\








\









\









\





\f

Fuel Tank  Capacity  24 gal (92L) 











\










\









\









\









\









\









\




\f



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 










\









\









\









\









\









\









\







WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE









\









\









\









\









\









\







Wheel Size Tire Size
15 x 6JJ (Steel or Aluminum) .................. P235/75R15
15 X 7JJ (Aluminum) ........................... P265/70R15









\









\









\









\









\









\







WHEEL TIGHTENING

allowing metal objects to contact the battery posts and the
vehicle at the same time.
CAUTION: Never disconnect the battery while the engine is running;
doing so could damage the car's electrical components.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
BRAKE FLUID
WARNING: DO NOT use reclaimed fluid or fluid that has been stored
in old or open containers. It is essential that foreign
particles and other liquids are kept out of the brake fluid
reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ENGINE COOLANT SERVICE
WARNING: To avoid the danger of being scalded never change the coolant
when the engine is hot.
WARNING: Never remove the radiator cap when the engine is hot Serious
burns could be caused by high pressure fluid escaping from
the radiator.
CAUTION: When adding or replacing engine coolant, use a high quality
ethylene glycol antifreeze diluted with 50% distilled water.
When putting the cap on the reserve tank, line up the arrow
on the cap and the arrow on the tank, or coolant can leak out
ENGINE DRIVE BELT SERVICE
WARNING: Be sure the ignition key is OFF. The engine could rotate
unexpectedly.
ENGINE OIL
WARNING: The engine oil may be high enough to burn your fingers
when the drain plug is loosened. Wait until the drain plug
is cool enough to touch with you bare hands.
WARNING: Continuous contact with used engine oil has been found to
cause skin cancer in laboratory animals. Brief contact with
used engine oil may irritate skin. To minimize your exposure
to used oil, wear a long sleeve shirt and moisture-proof
gloves when changing oil. If oil contacts your skin, wash

thoroughly with soap and water.
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare hands. Eye
protection should be worn when handling or working around halogen
bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to 15 minutes even
after engine is turned off.
WARRANTY INFORMATION
CAUTION: Due to the different warranties offered in various regions
and the variety of after-market extended warranties
available, please refer to the warranty package that came
with the vehicle to verify all warranty options.
FUSES & CIRCUIT BREAKERS
FUSE PANEL LOCATION
The electrical system is protected against shorts by fuses
that are designed to fail, to prevent damage to the wire harness. The
fuse block is located under the instrument panel on the driver's side.
If a fuse is blown, locate the cause before replacing the fuse. Spare
fuses are contained in the fuse block.
FUSE PANEL IDENTIFICATION
Fuse & Circuit Breaker Identification
PASSENGER COMPARTMENT

1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. Remove air intake
hose. Remove throttle body and gasket with control cables and vacuum
hoses attached.
2) Remove EGR pipe (if equipped). Disconnect power brake
hose. Label and disconnect vacuum hoses and wiring harness connectors
as necessary. Remove intake plenum brackets and mounting bolts. Remove
intake plenum and gasket.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return hose. Disconnect vacuum hoses. Disconnect
injector electrical connectors. Remove fuel rail bolts, and lift fuel
rail and injectors from engine. Injectors may be removed after fuel
rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Install injectors into fuel rail
with a twisting motion. Ensure injectors rotate smoothly when
installing. Refill cooling system.
Removal (Eclipse, Galant, Mirage & Montero Sport 3.0L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Disconnect PCV hose and breather
hoses. Disconnect high pressure fuel hose at fuel rail. Disconnect
fuel return hose and vacuum hoses.
2) Disconnect injector electrical connectors. Remove fuel
rail bolts, and lift fuel rail and injectors from engine. Injectors
may be removed after fuel rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Use lubricant on "O" rings.
Install injectors into fuel rail with a twisting motion. Ensure
injectors rotate smoothly when installing.
Removal (Montero)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Remove air intake hose. Remove
accelerator cable adjusting bolts. On A/T models, remove throttle
control cable. On all models, remove accelerator cable. Label and
disconnect all vacuum hoses from throttle body and upper intake
manifold (air intake plenum).
2) Remove EGR pipe and gasket. Remove ignition coil (if
necessary). Remove engine oil filler neck bracket. Disconnect PCV
hose. Remove throttle body, leaving coolant hoses connected. Remove
throttle body gasket. Remove front and rear intake plenum brackets.
Remove intake plenum mounting bolts. Remove intake plenum and gasket.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return hose. Disconnect vacuum hoses. Disconnect
injector electrical connectors. Remove fuel rail bolts, and lift fuel
rail and injectors from engine. Injectors may be removed after fuel
rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Use lubricant on "O" rings.
Install injectors into fuel rail using a twisting motion. Ensure
injectors rotate smoothly when installing. Adjust throttle control and
accelerator cables (if necessary). Refill cooling system.
HEATED OXYGEN SENSOR (HO2S)
Removal & Installation

1) Front HO2S is mounted in exhaust pipe below exhaust
header. Rear HO2S is mounted behind catalytic converter. HO2S is
equipped with a permanent pigtail which must be protected from damage
when HO2S is removed. Ensure HO2S is free of contaminants. Avoid using
cleaning solvents of any type.
2) HO2S may be difficult to remove when engine temperature is
less than 120
F (48C). If using original sensor, always use anti-
seize compound on threads before installation. New sensor threads are
precoated with anti-seize. Tighten HO2S to specification. See
TORQUE SPECIFICATIONS .
THROTTLE BODY
Removal
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Drain enough coolant to ensure coolant level is below throttle body.
Disconnect air intake hose.
2) Remove accelerator, cruise control and A/T throttle valve
cables (if equipped). Disconnect fuel vapor hose, electrical harness
connector, vacuum hose and coolant hoses. Remove throttle body
retaining bolts.
Disassembly
Remove throttle position sensor. Remove idle air control
motor. Remove throttle bracket and connector bracket (if equipped).
Remove idle position switch and adjusting nut (if equipped).
CAUTION: DO NOT remove throttle valve. DO NOT use cleaning solvents
on throttle position sensor, idle air control motor or idle
position switch.
Cleaning
1) Clean all parts except throttle position sensor, idle air
control motor and idle position switch in solvent.
WARNING: Safety glasses MUST be worn whenever compressed air is used
for parts cleaning.
2) Check vacuum port and passage for clogging. Clean vacuum,
vapor and fuel passages using compressed air.
Reassembly
To reassemble, reverse disassembly procedure.
Installation
To install, reverse removal procedure.
THROTTLE POSITION (TP) SENSOR
Removal & Installation
Throttle Position (TP) sensor is located on throttle body.
Disconnect TP sensor electrical connector. Remove TP sensor screws and
TP sensor. To install, reverse removal procedure. Tighten TP sensor
screws to specification. See TORQUE SPECIFICATIONS. For TP sensor
adjustment procedure, see D - ADJUSTMENTS article.
TURBOCHARGERS
Removal (Eclipse)
1) Disconnect negative battery cable. Drain engine coolant
and oil. On models equipped with A/C, remove condenser fan motor
assembly. Remove front heated oxygen sensor. Remove oil dipstick guide
and "O" ring.

2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect engine coolant hoses and tubes from
turbocharger. Remove exhaust manifold nuts and bolts. Remove exhaust
manifold and gaskets. Disconnect oil pressure and return pipes. Remove
turbocharger and exhaust manifold assembly. Separate turbocharger from
exhaust manifold.
Removal (3000GT - Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove generator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect front heated oxygen
sensor connector. Remove oil return pipe. Remove turbocharger support
bracket, and remove turbocharger from exhaust manifold.
Removal (3000GT - Rear)
1) Disconnect battery cables, and remove battery. Drain
engine oil and cooling system. Remove accelerator cable. Remove air
hose, air pipe and heat protectors. Disconnect clutch booster vacuum
hose. Remove air intake hoses and EGR pipe. Disconnect heated oxygen
sensor connectors.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting,
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly.
Inspection (All Models)
Check turbine and compressor wheels for cracking and other
damage. Ensure turbine and compressor wheels turn smoothly. Check for
oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See I - SYSTEM/COMPONENT TESTS article.
CAUTION: Apply light coat of oil to inner surface of flared area on
water pipe (flare nut fitting) before connecting to engine.
Installation (All Models)
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger oil pipe installation hole. Ensure oil and air hoses
are properly installed and securely clamped.
2) Use NEW gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\







Applications Ft. Lbs. (N.m)
Coolant Pipe-To-Turbocharger Banjo Bolt .......... 31 (42)
EGR Valve ........................................ 16 (22)
Engine Coolant Temperature Sensor ................ 22 (30)
Exhaust Manifold-To-Engine Nuts ............ 18-21 (24-29)
Exhaust Manifold-To-Turbocharger Bolts ..... 40-47 (54-64)
Exhaust Pipe Bolts ......................... 21-36 (29-49)
Fuel Filter Line ................................. 27 (36)
Fuel Tank Drain Plug ....................... 11-18 (15-24)
Fuel Tank Nuts ............................. 15-21 (20-29)