1998 MITSUBISHI MONTERO maintenance

Tighten wheel lug nuts to 72-87 ft. lbs. (100-120 N.m).
BATTERY SPECIFICATIONS
CAUTION: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
COMPUTER RELEARN PROCEDURES article in the GENERAL
INFORMATION Section.
Battery is maintenance-free and does not normally require
additional water. However, under severe conditions it is advisable to
check battery fluid periodically. Use only distilled water to fill
battery cell should it become necessary to add water. Charge condition
can be checked by a visual test indicator on top of battery.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAGS article in the ACCESSORIES/SAFETY EQUIPMENT
Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: Service on or around Air Bag System Components or Wiring must
be preformed only by an authorized Suzuki dealer. Please
observe all WARNINGS and SERVICE PRECAUTIONS.
WARNING: Technical service work must be started at least 90 seconds
after the ignition switch is turned to the LOCK position and
the cable is disconnected from the battery.
WARNING: Never attempt to disassemble or repair the passenger air
bag (inflator) module. If any abnormality is found, be sure
to replace it with new one as an assembly.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets

SCHEDULED SERVICES
1998 Mitsubishi Montero
1997-98 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Mitsubishi: Montero
* READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS in MAINTENANCE INFORMATION
article in this section.
Introduction
The frequency of scheduled inspection and maintenance
services in this article are based on "normal" vehicle usage. They DO
NOT take into account the following "severe" conditions:
* Driving In Dusty Conditions
* Trailer Towing, Police, Taxi, commercial Type Operation
* Extensive Idling, Driving In Stop-And-Go Traffic
* Short Trip Operation At Freezing Temperatures (Engine Not
Thoroughly Warmed Up)
* Driving In Sandy Areas
* Driving In Salty Areas
* More Than 50% Operation In Heavy City Traffic Or At Sustained
High Speeds During Hot Weather Above 90
F (32C)
* Driving On Off-Road
If any of these severe conditions exist, the "normal" service
schedule frequency for some service items is inadequate and must be
supplemented. See the following section for specific details,
SEVERE SERVICE CONDITIONS/ACTIONS .
SEVERE SERVICE CONDITIONS/ACTIONS
The following table identifies eight "severe" conditions that
cause faster-than-normal wear. Each condition lists affected service
item(s) and their revised (more frequent) service interval.
If any severe condition(s) is applicable, its revised service\
interval(s) supersede those found in the "normal" schedules. Depending\
on the specific mileage/time, the revised interval(s) may overlap a
normal schedule (in which case they can be done together). If not, it
must be performed outside of the normal schedule.
SEVERE SERVICE CONDITIONS/ACTIONS TABLE

\
\
\
\
\
\
\
 
Condition  Action  Item  Perform Every (1) 
\b
\
\
\
 \
 \
\
\



Driving In Dusty  Replace  Engine Oil  3,000 Mile (4800 KM) 

Conditions    Or 3 Months 

\b
\
\
 \
\
\



 Replace  Oil Filter  6,000 Mile (9600 KM) 

   Or 6 Months 

\b
\
\
 \
\
\



 Replace  Air Cleaner  15,000 Mile (24,000 KM) 

  Filter  

\b
\
\
 \
\
\



 Inspect  Disk Brake  6,000 Mile (9,600 KM) 

  Pads  Or 6 Months 

\b \
\
\
\
\
\
\



 Drive Shaft Boots (
4) 
\b
 \
\
\
\
\
\
\



 Exhaust System (
3) 
\b
 \
\
\
\
\
\
\



 Distributor Cap & Rotor (
7) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
 \
\
\
\
\
\
\



 Engine Coolant 
\b
 \
\
\
\
\
\
\



 Automatic Transmission Fluid 
\b
 \
\
\
\
\
\
\



 Rear Axle Oil 
\b
 \
\
\
\
\
\
\



 Spark Plugs 
\b
 \
\
\
\
\
\
\



 Timing Belt (
9) 
\b
 \
\
\
\
\
\
\



 Ignition Cables (
8) 
\b
 \
\
\
\
\
\
\



 Air Cleaner Filter 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every 2 years. 

(
4) - Or inspect every year. 

(
5) - Or change every 2 years. 

(
6) - Or lubricate grease every 2 years. 

(
7) - Or inspect every 5 years. 

(
8) - Or replace every 5 years. 

(
9) - For California & Massachusettes, this maintenance is 

recommended but not required. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2) 

  Engine Coolant 
\b
 \
\
\
\
\
\
\



 Automatic Transmission Fluid 
\b
 \
\
\
\
\
\
\



 Rear Axle Oil 
\b
 \
\
\
\
\
\
\



 Spark Plugs 
\b
 \
\
\
\
\
\
\



 Timing Belt (
9) 
\b
 \
\
\
\
\
\
\



 Ignition Cables (
8) 
\b
 \
\
\
\
\
\
\



 Air Cleaner Filter 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every 2 years. 

(
4) - Or inspect every year. 

(
5) - Or change every 2 years. 

(
6) - Or lubricate grease every 2 years. 

(
7) - Or inspect every 5 years. 

(
8) - Or replace every 5 years. 

(
9) - For California & Massachusettes, this maintenance is 

recommended but not required. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2) 
\b
\
 \
\
\
 \
\
\



Transfer Case All API Classification GL-4

  SAE 75W-85W Or 75W-90 
\b
\
\
\
\
\
\
\



(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 

(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above 

-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures 

from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used 

in temperatures below -30 F (-34 C). 
\b
\
\
\
\
\
\
\




FLUID CAPACITIES 
\b
\
\
\
\
\
\
\


TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-

profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.

Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition. When a procedure states that required or suggested
repair or replacement is recommended, the customer must be informed of
the generally acceptable repair/replacement options whether or not
performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial
service to the system in question, if the repair creates
or continues an unsafe condition.
Reasons to Suggest Repair or Replacement
1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise,
etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience
NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present

previously diagnosed by the "perceptible movement"
standard. Before requiring or suggesting any parts be
replaced based on "perceptible movement," consult your
repair manual to determine if OEM specifications exist.
You are not required to replace ball joints in axle sets.
However, when replacing a ball joint due to wear exceeding
manufacturer's specification, you may suggest replacement of the other
ball joint if its measurement shows it is close to the end of its
useful life, for preventive maintenance.
BALL JOINT INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part if available;
otherwise, replace ball joint.
Attaching hardware
broken ................. A ... Require replacement of broken
part if available; otherwise,
replace ball joint.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part if available; otherwise,
replace ball joint.
Attaching hardware
incorrect ............... A .......... Require replacement of
incorrect part if available;
otherwise, replace ball joint.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part if available;
otherwise, replace ball joint.
Attaching hardware
missing ................ C .. Require replacement of missing
part if available; otherwise,
replace ball joint.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads if
available; otherwise, replace
ball joint.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads if
available; otherwise, replace
ball joint.
Binding ................. A .......... (1) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 2) Suggest replacement.
Grease boot missing ..... 2 ........ ( 3) Suggest replacement.
Grease boot torn ........ 2 ........ ( 4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Greaseable ball joint will